Re: [Asterisk-Users] TE405P + Adit 600 and FXO module - should this work?
I have an Adit 600 working with a TDM400p card. - check this link for info on Adit-600 configuration http://lists.digium.com/pipermail/asterisk-users/2003-June/013072.html -Make sure the pinouts for your T1 cable are correct: DigiumT1 - RJ-48(F) X-over Digium T1 Card Channel Bank RJ-48(F) Pin Pair#T/R Color Pin T/R 12 T white/orange 4 R1 22 R orange/white 5T 41 T blue/white 1 R 51 R white/blue 2 T1 3, 6, 7, 8 Not assigned Darren Nickerson wrote: Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much luck getting this combination flying at all thus far. Should it work? I've been concentrating on the Adit T1 interface TE405P connection ... and have the following in zapata.conf: span=1,1,0,esf,b8zs fxsks=1-24 loadzone = us defaultzone=us At the end of my zaptel.conf, I have: signalling=fxs_ks group=2 callerid=Joe Schmoe (215) 555-1212 channel = 1-24 To get things flying, I do: modprobe zaptel modprobe wct4xxp which causes the TE405P card to activate, but show a single flashing red alarm on the configured span. The Adit's TDM controller also displays a solid red LED. Here's its status: Adit 600 status a:1 SLOT A: Status for DS1 1: Receive: Loss of Signal Transmit:RAI/Yellow Alarm Loopback:OFF Adit 600 I'm not sure I have the DS1 configured appropriately. It says: Adit 600 show a:1 SLOT A: Settings for DS1 1: Circuit ID: CAC DS1# A:1 Up/Down: UP Framing: ESF Line Coding: B8ZS Line Build Out: DSX-1 EQUALIZATION FOR 0-133 ft. (CSU 0dB) Loop Code Detection: ON Loopback:OFF FDL Type:None Can anyone familiar with the Adit 600 and/or TE405P see any obvious errors here? -Darren ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] TE405P + Adit 600 and FXO module - should this work?
Thanks! I'll spend some time with this information, check the pinouts and I should be well on my way. Glad to know it can work! ;-) -Darren -- Darren Nickerson Senior Sales Support Engineer iFAX Solutions, Inc. www.ifax.com [EMAIL PROTECTED] +1.215.438.4638 ext 8106 office +1.215.243.8335 fax - Original Message - From: Darren Nickerson [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Friday, April 16, 2004 1:29 AM Subject: [Asterisk-Users] TE405P + Adit 600 and FXO module - should this work? Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much luck getting this combination flying at all thus far. Should it work? I've been concentrating on the Adit T1 interface TE405P connection ... and have the following in zapata.conf: span=1,1,0,esf,b8zs fxsks=1-24 loadzone = us defaultzone=us At the end of my zaptel.conf, I have: signalling=fxs_ks group=2 callerid=Joe Schmoe (215) 555-1212 channel = 1-24 To get things flying, I do: modprobe zaptel modprobe wct4xxp which causes the TE405P card to activate, but show a single flashing red alarm on the configured span. The Adit's TDM controller also displays a solid red LED. Here's its status: Adit 600 status a:1 SLOT A: Status for DS1 1: Receive: Loss of Signal Transmit:RAI/Yellow Alarm Loopback:OFF Adit 600 I'm not sure I have the DS1 configured appropriately. It says: Adit 600 show a:1 SLOT A: Settings for DS1 1: Circuit ID: CAC DS1# A:1 Up/Down: UP Framing: ESF Line Coding: B8ZS Line Build Out: DSX-1 EQUALIZATION FOR 0-133 ft. (CSU 0dB) Loop Code Detection: ON Loopback:OFF FDL Type:None Can anyone familiar with the Adit 600 and/or TE405P see any obvious errors here? -Darren -- Darren Nickerson Senior Sales Support Engineer iFAX Solutions, Inc. www.ifax.com [EMAIL PROTECTED] +1.215.438.4638 ext 8106 office +1.215.243.8335 fax ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] TE405P + Adit 600 and FXO module - should this work?
Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much luck getting this combination flying at all thus far. Should it work? I've been concentrating on the Adit T1 interface TE405P connection ... and have the following in zapata.conf: span=1,1,0,esf,b8zs fxsks=1-24 loadzone = us defaultzone=us At the end of my zaptel.conf, I have: signalling=fxs_ks group=2 callerid=Joe Schmoe (215) 555-1212 channel = 1-24 To get things flying, I do: modprobe zaptel modprobe wct4xxp which causes the TE405P card to activate, but show a single flashing red alarm on the configured span. The Adit's TDM controller also displays a solid red LED. Here's its status: Adit 600 status a:1 SLOT A: Status for DS1 1: Receive: Loss of Signal Transmit:RAI/Yellow Alarm Loopback:OFF Adit 600 I'm not sure I have the DS1 configured appropriately. It says: Adit 600 show a:1 SLOT A: Settings for DS1 1: Circuit ID: CAC DS1# A:1 Up/Down: UP Framing: ESF Line Coding: B8ZS Line Build Out: DSX-1 EQUALIZATION FOR 0-133 ft. (CSU 0dB) Loop Code Detection: ON Loopback:OFF FDL Type:None Can anyone familiar with the Adit 600 and/or TE405P see any obvious errors here? -Darren -- Darren Nickerson Senior Sales Support Engineer iFAX Solutions, Inc. www.ifax.com [EMAIL PROTECTED] +1.215.438.4638 ext 8106 office +1.215.243.8335 fax ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users