Re: [asterisk-users] TE410P hardware problems
On Wed, Aug 03, 2011 at 10:36:24PM -0400, Dave George wrote: I opened the jumpers on the card putting them in T1 mode and it worked. I had them set to T1 using the options in the dahdi.conf file under /etc/modprobe.d/ That worked well for over a year until it started acting up. Any chance that in doing this you reseated the card? The jumpers are read by the driver, which then sets the mode. So when it comes to configuring the card they are functionally the same. But regardless, thanks for closing the loop on this. -- Shaun Ruffell Digium, Inc. | Linux Kernel Developer 445 Jan Davis Drive NW - Huntsville, AL 35806 - USA Check us out at: www.digium.com www.asterisk.org -- _ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] TE410P hardware problems
I opened the jumpers on the card putting them in T1 mode and it worked. I had them set to T1 using the options in the dahdi.conf file under /etc/modprobe.d/ That worked well for over a year until it started acting up. Dave -Original Message- From: asterisk-users-boun...@lists.digium.com [mailto:asterisk-users-boun...@lists.digium.com] On Behalf Of Eric Wieling Sent: Tuesday, August 02, 2011 11:43 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] TE410P hardware problems If it doesn't go green when you put a hard loopback on the port, then contact Digium support. -Original Message- From: asterisk-users-boun...@lists.digium.com [mailto:asterisk-users- boun...@lists.digium.com] On Behalf Of Dave George Sent: Tuesday, August 02, 2011 10:52 PM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: Re: [asterisk-users] TE410P hardware problems dmesg: wct4xxp :0a:03.0: SPAN 9: Primary Sync Source wct4xxp :0a:03.0: Span 2 configured for ESF/B8ZS wct4xxp :0a:03.0: SPAN 10: Primary Sync Source wct4xxp :0a:03.0: All spans in alarm : No validspan to source RCLK from wct4xxp :0a:03.0: RCLK source set to span 1 wct4xxp :0a:03.0: Span 3 configured for ESF/B8ZS wct4xxp :0a:03.0: SPAN 11: Primary Sync Source wct4xxp :0a:03.0: Span 4 configured for ESF/B8ZS wct4xxp :0a:03.0: SPAN 12: Primary Sync Source wct4xxp :0a:03.0: All spans in alarm : No validspan to source RCLK from wct4xxp :0a:03.0: RCLK source set to span 1 -- _ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] TE410P hardware problems
On Tue, Aug 02, 2011 at 09:22:46PM -0400, Dave George wrote: TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and restarting dahdi with no luck. The other two cards are working fine. I put a loop plug the ports and same problem. Any strange output in dmesg? Best guess is either the card has failed or it has started to unseat from it's PCI slot. Normally when it starts to unseat you'll see Version Synchronization Errors in dmesg when trying to load the card. -- Shaun Ruffell Digium, Inc. | Linux Kernel Developer 445 Jan Davis Drive NW - Huntsville, AL 35806 - USA Check us out at: www.digium.com www.asterisk.org -- _ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] TE410P hardware problems
Hi, We opened the server an checked that the cards were seated correctly and they are. I will have the tech completely remove them tomorrow and try again. I will post the results. Dave -Original Message- From: asterisk-users-boun...@lists.digium.com [mailto:asterisk-users-boun...@lists.digium.com] On Behalf Of Shaun Ruffell Sent: Tuesday, August 02, 2011 10:34 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] TE410P hardware problems On Tue, Aug 02, 2011 at 09:22:46PM -0400, Dave George wrote: TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and restarting dahdi with no luck. The other two cards are working fine. I put a loop plug the ports and same problem. Any strange output in dmesg? Best guess is either the card has failed or it has started to unseat from it's PCI slot. Normally when it starts to unseat you'll see Version Synchronization Errors in dmesg when trying to load the card. -- Shaun Ruffell Digium, Inc. | Linux Kernel Developer 445 Jan Davis Drive NW - Huntsville, AL 35806 - USA Check us out at: www.digium.com www.asterisk.org -- _ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] TE410P hardware problems
dmesg: wct4xxp :0a:03.0: SPAN 9: Primary Sync Source wct4xxp :0a:03.0: Span 2 configured for ESF/B8ZS wct4xxp :0a:03.0: SPAN 10: Primary Sync Source wct4xxp :0a:03.0: All spans in alarm : No validspan to source RCLK from wct4xxp :0a:03.0: RCLK source set to span 1 wct4xxp :0a:03.0: Span 3 configured for ESF/B8ZS wct4xxp :0a:03.0: SPAN 11: Primary Sync Source wct4xxp :0a:03.0: Span 4 configured for ESF/B8ZS wct4xxp :0a:03.0: SPAN 12: Primary Sync Source wct4xxp :0a:03.0: All spans in alarm : No validspan to source RCLK from wct4xxp :0a:03.0: RCLK source set to span 1 system.conf span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,1,0,esf,b8zs bchan=26-48 mtp2=25 span=3,1,0,esf,b8zs bchan=49-72 span=4,1,0,esf,b8zs bchan=73-96 span=5,1,0,esf,b8zs bchan=97-120 span=6,1,0,esf,b8zs bchan=121-144 span=7,1,0,esf,b8zs bchan=145-168 span=8,1,0,esf,b8zs bchan=169-192 span=9,1,0,esf,b8zs bchan=193-216 span=10,1,0,esf,b8zs bchan=217-240 span=11,1,0,esf,b8zs bchan=241-264 span=12,1,0,esf,b8zs bchan=265-288 Dave -Original Message- From: asterisk-users-boun...@lists.digium.com [mailto:asterisk-users-boun...@lists.digium.com] On Behalf Of Shaun Ruffell Sent: Tuesday, August 02, 2011 10:34 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] TE410P hardware problems On Tue, Aug 02, 2011 at 09:22:46PM -0400, Dave George wrote: TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and restarting dahdi with no luck. The other two cards are working fine. I put a loop plug the ports and same problem. Any strange output in dmesg? Best guess is either the card has failed or it has started to unseat from it's PCI slot. Normally when it starts to unseat you'll see Version Synchronization Errors in dmesg when trying to load the card. -- Shaun Ruffell Digium, Inc. | Linux Kernel Developer 445 Jan Davis Drive NW - Huntsville, AL 35806 - USA Check us out at: www.digium.com www.asterisk.org -- _ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] TE410P hardware problems
If it doesn't go green when you put a hard loopback on the port, then contact Digium support. -Original Message- From: asterisk-users-boun...@lists.digium.com [mailto:asterisk-users- boun...@lists.digium.com] On Behalf Of Dave George Sent: Tuesday, August 02, 2011 10:52 PM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: Re: [asterisk-users] TE410P hardware problems dmesg: wct4xxp :0a:03.0: SPAN 9: Primary Sync Source wct4xxp :0a:03.0: Span 2 configured for ESF/B8ZS wct4xxp :0a:03.0: SPAN 10: Primary Sync Source wct4xxp :0a:03.0: All spans in alarm : No validspan to source RCLK from wct4xxp :0a:03.0: RCLK source set to span 1 wct4xxp :0a:03.0: Span 3 configured for ESF/B8ZS wct4xxp :0a:03.0: SPAN 11: Primary Sync Source wct4xxp :0a:03.0: Span 4 configured for ESF/B8ZS wct4xxp :0a:03.0: SPAN 12: Primary Sync Source wct4xxp :0a:03.0: All spans in alarm : No validspan to source RCLK from wct4xxp :0a:03.0: RCLK source set to span 1 -- _ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
