Re: [OSL | CCIE_Voice] Adding subscriber problem - need ideas
Dear Jason, Shingei, I am installing 7.0 CUCM om MCS servers. I did reset the passowrd and reload the pub after applying license. Do you have any good doc. for troubleshooting this issue ? Regards, Wael Agina On Fri, Nov 26, 2010 at 8:17 AM, Jason Aarons (US) jason.aar...@us.didata.com wrote: I had this problem with a recent new install of 8.0.2c (it was pre-installed on the hard drive on new MCS server) . I couldn’t find anything wrong, the password I reset 20 times, etc. I upgraded the pub to 8.0.3a and did a subscriber install with software update on the subscriber and it worked fine. *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *Wael Agina *Sent:* Thursday, November 25, 2010 5:29 PM *To:* Michael Dietrich *Cc:* OSL Group *Subject:* Re: [OSL | CCIE_Voice] Adding subscriber problem - need ideas Dearl Michael First i have applied license for two nodes and only using one and there is one available node on the lices [for sub] Also I set the name with uppercase all lettters and tried on sub both upper case and lower case but not working. I did reset security password many times to cisco12345 on pub and used it on sub but no sccess. Is there any troubleshooting steps can be done on pub during connectivity test on sub ? Regards, Wael Agina On Fri, Nov 26, 2010 at 1:23 AM, Michael Dietrich mdd2...@gmail.com wrote: Make sure that you are entering the device name of the PUB correctly (spelling) during the SUB set up Make sure the server name for SUB is spelled correctly on the PUB (case sensitive)...AND. that you have a second server license installed on the PUB, to be used by the SUB On Thu, Nov 25, 2010 at 3:13 PM, Wael Agina waelag...@gmail.com wrote: Hi Prashant , Yes I added it on the publisher on server list and on the CM Group. But still it fails the connectivity test when installing subscriber software. Regards, Wael Agina On Fri, Nov 26, 2010 at 12:31 AM, Prashant Patel prashantpatel...@gmail.com wrote: Hi, Hope you have added the Sub in the list of servers on the Publisher. HTH Prashant On Thu, Nov 25, 2010 at 4:25 PM, Wael Agina waelag...@gmail.com wrote: Dear All, I am implemnting new UC project at one customer location. I installed the first node - publisher - succefully. Now whenevr i add the 2nd node - subscriber - it tried to test connectivity to first node but always fails and installion terminated. There is network connectivity between the two nodes and from publisher i can ping the new node - subscriber. Also I reset the security password on the publisher [using Set *password*user *security on CLI]* Any ideas as the connectivity test always fails ? -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com -- Thanks and Best Regards, Wael Agina -- * Disclaimer: This e-mail communication and any attachments may contain confidential and privileged information and is for use by the designated addressee(s) named above only. If you are not the intended addressee, you are hereby notified that you have received this communication in error and that any use or reproduction of this email or its contents is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Thank you. * -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Adding subscriber problem - need ideas
Dear Rogers, It is new installation with no DNS setup at all. I havent set any DNS info, and chosed no DNS during installation. Also when you reach to connectivity test I entered both pub Name and IP address. Still not working and connectivity test fails ? Regards, Wael Agina On Fri, Nov 26, 2010 at 11:47 AM, Rogers Ochieng rogersochi...@gmail.comwrote: Off the top of my head, could it be because of DNS resolution of the host name? I got that when installing recently on VMWARE and as i didn't have DNS setup. I ignored it and continued to setup well On 26 November 2010 11:40, Wael Agina waelag...@gmail.com wrote: Dear Jason, Shingei, I am installing 7.0 CUCM om MCS servers. I did reset the passowrd and reload the pub after applying license. Do you have any good doc. for troubleshooting this issue ? Regards, Wael Agina On Fri, Nov 26, 2010 at 8:17 AM, Jason Aarons (US) jason.aar...@us.didata.com wrote: I had this problem with a recent new install of 8.0.2c (it was pre-installed on the hard drive on new MCS server) . I couldn’t find anything wrong, the password I reset 20 times, etc. I upgraded the pub to 8.0.3a and did a subscriber install with software update on the subscriber and it worked fine. *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *Wael Agina *Sent:* Thursday, November 25, 2010 5:29 PM *To:* Michael Dietrich *Cc:* OSL Group *Subject:* Re: [OSL | CCIE_Voice] Adding subscriber problem - need ideas Dearl Michael First i have applied license for two nodes and only using one and there is one available node on the lices [for sub] Also I set the name with uppercase all lettters and tried on sub both upper case and lower case but not working. I did reset security password many times to cisco12345 on pub and used it on sub but no sccess. Is there any troubleshooting steps can be done on pub during connectivity test on sub ? Regards, Wael Agina On Fri, Nov 26, 2010 at 1:23 AM, Michael Dietrich mdd2...@gmail.com wrote: Make sure that you are entering the device name of the PUB correctly (spelling) during the SUB set up Make sure the server name for SUB is spelled correctly on the PUB (case sensitive)...AND. that you have a second server license installed on the PUB, to be used by the SUB On Thu, Nov 25, 2010 at 3:13 PM, Wael Agina waelag...@gmail.com wrote: Hi Prashant , Yes I added it on the publisher on server list and on the CM Group. But still it fails the connectivity test when installing subscriber software. Regards, Wael Agina On Fri, Nov 26, 2010 at 12:31 AM, Prashant Patel prashantpatel...@gmail.com wrote: Hi, Hope you have added the Sub in the list of servers on the Publisher. HTH Prashant On Thu, Nov 25, 2010 at 4:25 PM, Wael Agina waelag...@gmail.com wrote: Dear All, I am implemnting new UC project at one customer location. I installed the first node - publisher - succefully. Now whenevr i add the 2nd node - subscriber - it tried to test connectivity to first node but always fails and installion terminated. There is network connectivity between the two nodes and from publisher i can ping the new node - subscriber. Also I reset the security password on the publisher [using Set *password * user *security on CLI]* Any ideas as the connectivity test always fails ? -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com -- Thanks and Best Regards, Wael Agina -- * Disclaimer: This e-mail communication and any attachments may contain confidential and privileged information and is for use by the designated addressee(s) named above only. If you are not the intended addressee, you are hereby notified that you have received this communication in error and that any use or reproduction of this email or its contents is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Thank you. * -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Adding subscriber problem - need ideas
Wael, Try to upgrade Pub to latest service release, and point the service release to the Sub during installation. Best regards, Connect Logo copy Tamer Ismail CONNECT Professional Services Website: http://www.connectps.com/ www.connectps.com From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Wael Agina Sent: Friday, November 26, 2010 12:21 PM To: Rogers Ochieng Cc: OSL Group Subject: Re: [OSL | CCIE_Voice] Adding subscriber problem - need ideas Dear Rogers, It is new installation with no DNS setup at all. I havent set any DNS info, and chosed no DNS during installation. Also when you reach to connectivity test I entered both pub Name and IP address. Still not working and connectivity test fails ? Regards, Wael Agina On Fri, Nov 26, 2010 at 11:47 AM, Rogers Ochieng rogersochi...@gmail.com wrote: Off the top of my head, could it be because of DNS resolution of the host name? I got that when installing recently on VMWARE and as i didn't have DNS setup. I ignored it and continued to setup well On 26 November 2010 11:40, Wael Agina waelag...@gmail.com wrote: Dear Jason, Shingei, I am installing 7.0 CUCM om MCS servers. I did reset the passowrd and reload the pub after applying license. Do you have any good doc. for troubleshooting this issue ? Regards, Wael Agina On Fri, Nov 26, 2010 at 8:17 AM, Jason Aarons (US) jason.aar...@us.didata.com wrote: I had this problem with a recent new install of 8.0.2c (it was pre-installed on the hard drive on new MCS server) . I couldn't find anything wrong, the password I reset 20 times, etc. I upgraded the pub to 8.0.3a and did a subscriber install with software update on the subscriber and it worked fine. From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Wael Agina Sent: Thursday, November 25, 2010 5:29 PM To: Michael Dietrich Cc: OSL Group Subject: Re: [OSL | CCIE_Voice] Adding subscriber problem - need ideas Dearl Michael First i have applied license for two nodes and only using one and there is one available node on the lices [for sub] Also I set the name with uppercase all lettters and tried on sub both upper case and lower case but not working. I did reset security password many times to cisco12345 on pub and used it on sub but no sccess. Is there any troubleshooting steps can be done on pub during connectivity test on sub ? Regards, Wael Agina On Fri, Nov 26, 2010 at 1:23 AM, Michael Dietrich mdd2...@gmail.com wrote: Make sure that you are entering the device name of the PUB correctly (spelling) during the SUB set up Make sure the server name for SUB is spelled correctly on the PUB (case sensitive)...AND. that you have a second server license installed on the PUB, to be used by the SUB On Thu, Nov 25, 2010 at 3:13 PM, Wael Agina waelag...@gmail.com wrote: Hi Prashant , Yes I added it on the publisher on server list and on the CM Group. But still it fails the connectivity test when installing subscriber software. Regards, Wael Agina On Fri, Nov 26, 2010 at 12:31 AM, Prashant Patel prashantpatel...@gmail.com wrote: Hi, Hope you have added the Sub in the list of servers on the Publisher. HTH Prashant On Thu, Nov 25, 2010 at 4:25 PM, Wael Agina waelag...@gmail.com wrote: Dear All, I am implemnting new UC project at one customer location. I installed the first node - publisher - succefully. Now whenevr i add the 2nd node - subscriber - it tried to test connectivity to first node but always fails and installion terminated. There is network connectivity between the two nodes and from publisher i can ping the new node - subscriber. Also I reset the security password on the publisher [using Set password user security on CLI] Any ideas as the connectivity test always fails ? -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com http://www.ipexpert.com/ -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com http://www.ipexpert.com/ -- Thanks and Best Regards, Wael Agina _ Disclaimer: This e-mail communication and any attachments may contain confidential and privileged information and is for use by the designated addressee(s) named above only. If you are not the intended addressee, you are hereby notified that you have received this communication in error and that any use or reproduction of this email or its contents is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Thank you. -- Thanks and Best
Re: [OSL | CCIE_Voice] Adding subscriber problem - need ideas
Dear Rogers, yes it is up as i am reaching the pub over the network from another LAN subnet and it is pingable. Do I have to try reloading the pub ? Restart some services ? Regards, Wale Agina On Fri, Nov 26, 2010 at 1:34 PM, Rogers Ochieng rogersochi...@gmail.comwrote: Is the default gateway up? I had this error and i just ignored it and proceeded On 26 November 2010 12:21, Wael Agina waelag...@gmail.com wrote: Dear Rogers, It is new installation with no DNS setup at all. I havent set any DNS info, and chosed no DNS during installation. Also when you reach to connectivity test I entered both pub Name and IP address. Still not working and connectivity test fails ? Regards, Wael Agina On Fri, Nov 26, 2010 at 11:47 AM, Rogers Ochieng rogersochi...@gmail.com wrote: Off the top of my head, could it be because of DNS resolution of the host name? I got that when installing recently on VMWARE and as i didn't have DNS setup. I ignored it and continued to setup well On 26 November 2010 11:40, Wael Agina waelag...@gmail.com wrote: Dear Jason, Shingei, I am installing 7.0 CUCM om MCS servers. I did reset the passowrd and reload the pub after applying license. Do you have any good doc. for troubleshooting this issue ? Regards, Wael Agina On Fri, Nov 26, 2010 at 8:17 AM, Jason Aarons (US) jason.aar...@us.didata.com wrote: I had this problem with a recent new install of 8.0.2c (it was pre-installed on the hard drive on new MCS server) . I couldn’t find anything wrong, the password I reset 20 times, etc. I upgraded the pub to 8.0.3a and did a subscriber install with software update on the subscriber and it worked fine. *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *Wael Agina *Sent:* Thursday, November 25, 2010 5:29 PM *To:* Michael Dietrich *Cc:* OSL Group *Subject:* Re: [OSL | CCIE_Voice] Adding subscriber problem - need ideas Dearl Michael First i have applied license for two nodes and only using one and there is one available node on the lices [for sub] Also I set the name with uppercase all lettters and tried on sub both upper case and lower case but not working. I did reset security password many times to cisco12345 on pub and used it on sub but no sccess. Is there any troubleshooting steps can be done on pub during connectivity test on sub ? Regards, Wael Agina On Fri, Nov 26, 2010 at 1:23 AM, Michael Dietrich mdd2...@gmail.com wrote: Make sure that you are entering the device name of the PUB correctly (spelling) during the SUB set up Make sure the server name for SUB is spelled correctly on the PUB (case sensitive)...AND. that you have a second server license installed on the PUB, to be used by the SUB On Thu, Nov 25, 2010 at 3:13 PM, Wael Agina waelag...@gmail.com wrote: Hi Prashant , Yes I added it on the publisher on server list and on the CM Group. But still it fails the connectivity test when installing subscriber software. Regards, Wael Agina On Fri, Nov 26, 2010 at 12:31 AM, Prashant Patel prashantpatel...@gmail.com wrote: Hi, Hope you have added the Sub in the list of servers on the Publisher. HTH Prashant On Thu, Nov 25, 2010 at 4:25 PM, Wael Agina waelag...@gmail.com wrote: Dear All, I am implemnting new UC project at one customer location. I installed the first node - publisher - succefully. Now whenevr i add the 2nd node - subscriber - it tried to test connectivity to first node but always fails and installion terminated. There is network connectivity between the two nodes and from publisher i can ping the new node - subscriber. Also I reset the security password on the publisher [using Set * password* user *security on CLI]* Any ideas as the connectivity test always fails ? -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com -- Thanks and Best Regards, Wael Agina ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com -- Thanks and Best Regards, Wael Agina -- * Disclaimer: This e-mail communication and any attachments may contain confidential and privileged information and is for use by the designated addressee(s) named above only. If you are not the intended addressee, you are hereby notified that you have received this communication in error and that any use or reproduction of this email or its contents is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Thank you. * -- Thanks and Best Regards, Wael Agina
Re: [OSL | CCIE_Voice] Integration of CUE with CUCM through cli
Thanks for clarification ! Regards, MJ On Thu, Nov 25, 2010 at 11:48 PM, ccieid1ot ccieid...@gmail.com wrote: The GUI ask for 2 types in order to integrate the users as well which uses the user in the AXL group assigned. On Thu, Nov 25, 2010 at 11:32 AM, Mritunjay Kumar mjs...@gmail.comwrote: Hi All , I have doubts in CUE with CUCM integration 1. When I try to register CUE with CUCM through GUI , Two type of credential is asked after login into CUE WEB user and password ie cucm application user and password if I m not wrong And Jtapi credential When I try to integrate using cli , I am able to given JTAPI credentials but not the cucm credentials ie application account credentials CUE-CUCM(config-jtapi)# ccm-manager ? address IP address of the Call Manager credentials CCM JTAPI user credentials username Account name for CCM JTAPI User login // Jtapi account ccm-manager credentials ? // I guess this is asking for application account credential of cucm . I am not able to give it as it asked for encoded credential hiddenEncoded username/password value CUE-CUCM(config-jtapi)# ccm-manager credentials But integration works ie all feature without giving ccm credentials !! Is this expected ? why GUI ask two type of credentials ? Regards, MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Forwarded number display on branch phone
Hi Mates , Unable to make it work :( Branch phone 3001 in SRST and CFUR is configured on CUCM, when HQ phone 2001 is making a call to Branch phone 3001 , display should be on branch phone Forward 2001, For + 19723033002 By + 19723033002 my configuration CALL forward unregister +13013013001 // CSS is configured to hit route pattern \+! and call is going through gateway route pattern \+.! and Predot output of q931 on HQ router Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98382 Exclusive, Channel 2 Calling Party Number i = 0x0081, '2001' Plan:Unknown, Type:Unknown Called Party Number i = 0xA1, '13013013001' Plan:ISDN, Type:National Redirecting Number i = 0x82, '3001' Plan:Unknown, Type:Unknown at the branch router , m changing every called number to 4 digit through translation pattern applied on voice port to hit the registered ext. not sure where to change the called and re direct number :( is there any better approach ? thx, Rahul ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Cbarge in SRST
Hi All I have couple of doubts in Cbarge 1. Cbarge is configured on CME , working fine. After pressing Cbagre soft key , three phones are connected but i dont see To conference on phone display. i see two same message To Barge. is this expected ? 2. CME in srst mode , created ephone and octo line ephone -dn and its working fine. but if the requirement is running config should not have any ephone config and then how it can be achieved ? what i have observed , ephone and ephone-dn template configured under telephony service which will be applied for learned ephone and ephone-dn does not work consistently. if question ask , privacy should be disabled on one phone then , we have to create ephone template if ruuning config should not have any config ! does anybody face this issue ? Regards, MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Cbarge in SRST
HI, there is a BUg in IOS.Seach in the cisco and you ´ll see the solution. Em 26/11/2010 14:52, Mritunjay Kumar mjs...@gmail.com escreveu:Hi AllI have couple of doubts in Cbarge1. Cbarge is configured on CME , working fine. After pressing Cbagre soft key , three phones are connected but i dont see "To conference" on phone display. i see two same message " To Barge". is this expected ? 2. CME in srst mode , created ephone and octo line ephone -dn and its working fine.but if the requirement is "running config should not have any ephone config " and then how it can be achieved ? what i have observed , ephone and ephone-dn template configured under telephony service which will be applied for learned ephone and ephone-dn does not work consistently. if question ask , privacy should be disabled on one phone then , we have to create ephone template if ruuning config should not have any config ! does anybody face this is sue ? Regards,MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] busy-trigger-per-button not working
Hello Mate, It seems busy-trigger-per-button is not working this is ephone config ephone 2 privacy-button device-security-mode none mac-address D057.4CF7.9A97 busy-trigger-per-button 1 button 1:2 ephone-dn 2 dual number 5002 phone is able to receive two incoming call on button 1 ! i m configuring following and want to make sure that config is fine . Octo shared line 1st phone should not receive not more than 4 incoming call and 2nd phone should receive more than two ephone-dn 10 octo number 1234 huntstop channel 5 ephone 1 busy-trigger-per-button 4 ephone 2 busy-trigger-per-button 2 Need to test in my lab and but got confused becos for me busy-trigger-per-button is not working as expected :( m i missing any thing ? thx, Rahul ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] busy-trigger-per-button not working
Hi, busy trigger works only with octo lines. regards kobel On Fri, Nov 26, 2010 at 19:34, Rahul Kapor rahul.kapo...@gmail.com wrote: Hello Mate, It seems busy-trigger-per-button is not working this is ephone config ephone 2 privacy-button device-security-mode none mac-address D057.4CF7.9A97 busy-trigger-per-button 1 button 1:2 ephone-dn 2 dual number 5002 phone is able to receive two incoming call on button 1 ! i m configuring following and want to make sure that config is fine . Octo shared line 1st phone should not receive not more than 4 incoming call and 2nd phone should receive more than two ephone-dn 10 octo number 1234 huntstop channel 5 ephone 1 busy-trigger-per-button 4 ephone 2 busy-trigger-per-button 2 Need to test in my lab and but got confused becos for me busy-trigger-per-button is not working as expected :( m i missing any thing ? thx, Rahul ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] busy-trigger-per-button not working
Hi Rahul, Try using huntstop channel. HTH Prashant On Fri, Nov 26, 2010 at 1:34 PM, Rahul Kapor rahul.kapo...@gmail.comwrote: Hello Mate, It seems busy-trigger-per-button is not working this is ephone config ephone 2 privacy-button device-security-mode none mac-address D057.4CF7.9A97 busy-trigger-per-button 1 button 1:2 ephone-dn 2 dual number 5002 phone is able to receive two incoming call on button 1 ! i m configuring following and want to make sure that config is fine . Octo shared line 1st phone should not receive not more than 4 incoming call and 2nd phone should receive more than two ephone-dn 10 octo number 1234 huntstop channel 5 ephone 1 busy-trigger-per-button 4 ephone 2 busy-trigger-per-button 2 Need to test in my lab and but got confused becos for me busy-trigger-per-button is not working as expected :( m i missing any thing ? thx, Rahul ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Cbarge in SRST
CSCti11843 Bug Details Shared-line Cbarge remote-in-use softkeys not working in SRST Symptom: For Shared line if you want cbarge you must disable privacy and enable remote-in-use softkey under ephone-template. However if you configured SRST CME with srst mode auto-provision none or dn privacy setting on the ephone remains default which means it is on. Hence you can't disable privacy. Conditions: When phones fallback to SRST. Workaround: Only workaround is to either configure: ephone 1 privacy off or configure srst mode auto-provision all Hope it helps! My way of giving back to the community: F. Date: Fri, 26 Nov 2010 15:56:12 -0200 From: malexand...@uol.com.br To: mjs...@gmail.com CC: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Cbarge in SRST HI, there is a BUg in IOS.Seach in the cisco and you ´ll see the solution. Em 26/11/2010 14:52, Mritunjay Kumar mjs...@gmail.com escreveu: Hi All I have couple of doubts in Cbarge 1. Cbarge is configured on CME , working fine. After pressing Cbagre soft key , three phones are connected but i dont see To conference on phone display. i see two same message To Barge. is this expected ? 2. CME in srst mode , created ephone and octo line ephone -dn and its working fine. but if the requirement is running config should not have any ephone config and then how it can be achieved ? what i have observed , ephone and ephone-dn template configured under telephony service which will be applied for learned ephone and ephone-dn does not work consistently. if question ask , privacy should be disabled on one phone then , we have to create ephone template if ruuning config should not have any config ! does anybody face this is sue ? Regards, MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Forwarded number display on branch phone
Hi, how are the numbers displayed when they hit the Branch GW? Do have have an deb isdn 931 from the Branch? /Robert Von: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] Im Auftrag von Rahul Kapor Gesendet: Freitag, 26. November 2010 18:33 An: ccie_voice@onlinestudylist.com Betreff: [OSL | CCIE_Voice] Forwarded number display on branch phone Hi Mates , Unable to make it work :( Branch phone 3001 in SRST and CFUR is configured on CUCM, when HQ phone 2001 is making a call to Branch phone 3001 , display should be on branch phone Forward 2001, For + 19723033002 By + 19723033002 my configuration CALL forward unregister +13013013001 // CSS is configured to hit route pattern \+! and call is going through gateway route pattern \+.! and Predot output of q931 on HQ router Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98382 Exclusive, Channel 2 Calling Party Number i = 0x0081, '2001' Plan:Unknown, Type:Unknown Called Party Number i = 0xA1, '13013013001' Plan:ISDN, Type:National Redirecting Number i = 0x82, '3001' Plan:Unknown, Type:Unknown at the branch router , m changing every called number to 4 digit through translation pattern applied on voice port to hit the registered ext. not sure where to change the called and re direct number :( is there any better approach ? thx, Rahul ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] CME- Can not call Vocie Hunt Group Pilot from PSTN Phone
Folks, CME- Can not call Vocie Hunt Group Pilot from PSTN Phone, get Fast busy and ISDN message unallocated/ unassingned number, I can call from another CME phone though. I see the call hitting the CME Thanks for your help AB ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] CME- Can not call Vocie Hunt Group Pilot from PSTN Phone
Can you send your configs? It's hard to troubleshoot without anything to work with. Thanks! Matthew Berry On Nov 26, 2010, at 7:22 PM, vccie2010 wrote: Folks, CME- Can not call Vocie Hunt Group Pilot from PSTN Phone, get Fast busy and ISDN message unallocated/ unassingned number, I can call from another CME phone though. I see the call hitting the CME Thanks for your help AB ATT1..txt ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] CME- Can not call Vocie Hunt Group Pilot from PSTN Phone
My bad, was a type in translation rule. thanks for your willingness to help please... On Fri, Nov 26, 2010 at 5:24 PM, Matthew Berry matthew.be...@cdw.comwrote: Can you send your configs? It's hard to troubleshoot without anything to work with. Thanks! Matthew Berry On Nov 26, 2010, at 7:22 PM, vccie2010 wrote: Folks, CME- Can not call Vocie Hunt Group Pilot from PSTN Phone, get Fast busy and ISDN message unallocated/ unassingned number, I can call from another CME phone though. I see the call hitting the CME Thanks for your help AB ATT1..txt ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com