Re: [OSL | CCIE_Voice] CCIE LAB at Dubai
Hi, I had attempted lab couple of months ago in Dubai, speed was pretty good, only the student PC is bit slow, but that is managable. I am attempting again in Dubai. Good luck for your lab ! Thanks&Rgds Deepak Sidana. From: CCIE For ME To: Ken Wyan ; Jon H Cc: ccie_voice@onlinestudylist.com Sent: Tuesday, 6 September 2011 10:29 PM Subject: Re: [OSL | CCIE_Voice] CCIE LAB at Dubai RTP and San Jose are now hosted in Dallas From: Ken Wyan Sent: Tuesday, September 06, 2011 1:06 PM To: Jon H Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] CCIE LAB at Dubai Hi Jon, Are all remote labs are hosted from San Jose? What about RTP? Is it also hosted from San Jose? Ken On Tue, Sep 6, 2011 at 7:50 PM, Jon H wrote: Adil > >I would say that makes sense. >I know when I attempted in Tokyo lab for voice, there were 3 other candidates >running R&S. >The speeds were ok. 2nd attempt was on a Monday and again 2 candidates for >R&S, and speeds were excellent, so I think it does matter how many people, >also the idea that the US was offline at the same time may help. Remember all >systems plug in to San Jose, so the less people online the better, Sydney time >wise is faster then the other locations in Asia so the first few hours will >most likely be faster then other locations, again backwards thinking Dubai, or >other locations away from the US also during US non business hours might get >better speeds as well during the time other lab locations are closed, not SJ >but other locations globaly trying to use the same bandwidth into the San Jose >systems. > >From: Adil Shaikh >Sent: Tuesday, September 06, 2011 1:54 AM >To: Ashraf Ayyash >Cc: ccie_voice@onlinestudylist.com >Subject: Re: [OSL | CCIE_Voice] CCIE LAB at Dubai >Has anyone come across following situation? > >Sydney has only one voice seat. >I did two attempt in sydney. On first attempt, the lab was slow. At that time, >there were 6 other people doing their lab on other tracks. > >On my second attempt, lab was of acceptable speed. At that time, I was the >only person doing the lab. There was not a single person doing other track. > >Does the number of people attempting lab (not from your own track) causes the >slowness of speed? > >-adil > >On Tue, Sep 6, 2011 at 6:21 AM, Ashraf Ayyash wrote: >Dubai lab is very slow (not always , its up to your chance ) and very busy , >they got 1 seat to serve the middle east so if you want to get seat now , you >will need to wait for about 2-3 months in advanced . >> >>Ash >> >> >>On Mon, Sep 5, 2011 at 9:26 PM, eng_firasoq...@yahoo.com >> wrote: >>Dear all, >>> >>>I want to ask about ccie lab in dubai,why alot of people didn't take there >>>lab in dubai even if they are in middle east region? alot of people told me >>>that the lab is too much slow in Dubai so please can you advice. >>> >>>Regards >>> ___ >>>For more information regarding industry leading CCIE Lab training, please >>>visit www.ipexpert.com >>> >>>Are you a CCNP or CCIE and looking for a job? Check out >>>www.PlatinumPlacement.com >>> >> >>___ >>For more information regarding industry leading CCIE Lab training, please >>visit www.ipexpert.com >> >>Are you a CCNP or CCIE and looking for a job? Check out >>www.PlatinumPlacement.com >>-- > . . . . >_7___|___|_|_| >adil.sha...@gmail.com > . . > > >___For more information regarding >industry leading CCIE Lab training, please visit www.ipexpert.comAre you a >CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com >___ >For more information regarding industry leading CCIE Lab training, please >visit www.ipexpert.com > >Are you a CCNP or CCIE and looking for a job? Check out >www.PlatinumPlacement.com >___For more information regarding >industry leading CCIE Lab training, please visit www.ipexpert.comAre you a >CCNP or CCIE and looking for a job? Check out >www.PlatinumPlacement.com___For >more information regarding industry leading CCIE Lab training, please visit >www.ipexpert.comAre you a CCNP or CCIE and looking for a job? Check out >www.PlatinumPlacement.com___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] CME Speed Dials
Dear All, One of my client is using CME 7.0 they need that the phone user can manage their speed dial from the phone. I have checked the CME admin guide, but could't find much info. Do we need to create any specific url to acheive this. below is the config of my telephony-services. telephony-service em logout 0:0 0:0 0:0 max-ephones 10 max-dn 14 ip source-address 192.168.1.10 port 2000 url directories http://192.168.1.10/localdirectory max-conferences 8 gain -6 transfer-system full-consult directory entry 1 1001 name user1 create cnf-files version-stamp Jan 01 2002 00:00:00 Thanks&Rgds Deepak Sidana. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUE MWI
Thanks Shitij, Is there any document for this, as i am not able to find it, Is there any workaround for this ? BR Deepak From: Kshitij Singhi To: ccie_voice@onlinestudylist.com Sent: Saturday, 2 July 2011 11:36 PM Subject: Re: [OSL | CCIE_Voice] CUE MWI Hi Deepak, This is expected behavior. The MWI off event is sent only once the message is deleted/saved. Reading the message and leaving it in the inbox does not trigger an MWI off. On Sat, Jul 2, 2011 at 9:30 PM, wrote: Send CCIE_Voice mailing list submissions to > ccie_voice@onlinestudylist.com > >To subscribe or unsubscribe via the World Wide Web, visit > http://onlinestudylist.com/mailman/listinfo/ccie_voice >or, via email, send a message with subject or body 'help' to > ccie_voice-requ...@onlinestudylist.com > >You can reach the person managing the list at > ccie_voice-ow...@onlinestudylist.com > >When replying, please edit your Subject line so it is more specific >than "Re: Contents of CCIE_Voice digest..." > > >Today's Topics: > > 1. Re: B-ACD Drop Through (Cristobal Priego) > 2. Re: I need vouchers (Marko Milivojevic) > 3. Re: B-ACD Drop Through (Victor Malyuga) > 4. CUE MWI (Deepak sidana) > > >-- > >Message: 1 >Date: Fri, 1 Jul 2011 15:44:46 -0700 >From: Cristobal Priego >To: Pablo Meneses >Cc: ccie voice >Subject: Re: [OSL | CCIE_Voice] B-ACD Drop Through >Message-ID: >Content-Type: text/plain; charset="iso-8859-1" > >i don't think that;s configurable > >2011/6/30 Pablo Meneses > >> Hi experts, >> >> Is there a way to display "1 call on phone" when using B-ACD Drop Through? >> >> I think that it will display "1 call on queue" and that there is no way for >> it to display "1 call on phone", but, I better ask. >> >> Regards, >> >> -Pablo Meneses. >> >> ___ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> Are you a CCNP or CCIE and looking for a job? Check out >> www.PlatinumPlacement.com >> >-- next part -- >An HTML attachment was scrubbed... >URL: > >-- > >Message: 2 >Date: Fri, 1 Jul 2011 15:53:28 -0700 >From: Marko Milivojevic >To: CCIE STUDENT >Cc: "ccie_voice@onlinestudylist.com" >Subject: Re: [OSL | CCIE_Voice] I need vouchers >Message-ID: >Content-Type: text/plain; charset=UTF-8 > >On Fri, Jul 1, 2011 at 12:59, CCIE STUDENT wrote: >> Looking for 15-20 vouchers. ?Please pm me if selling and the cost. > >Please, don't post these kinds of messages on OSL. I have sent warning >numerous times on the list. Please be advised that selling and >reselling is against the policies of Online Study List. > >-- >Marko Milivojevic - CCIE #18427 >Senior Technical Instructor - IPexpert > >FREE CCIE training: http://bit.ly/vLecture > >Mailto: mar...@ipexpert.com >Telephone: +1.810.326.1444 >Web: http://www.ipexpert.com/ > > >-- > >Message: 3 >Date: Sat, 2 Jul 2011 08:04:41 +0100 (BST) >From: Victor Malyuga >To: Pablo Meneses , Cristobal Priego > >Cc: ccie voice >Subject: Re: [OSL | CCIE_Voice] B-ACD Drop Through >Message-ID: > <1309590281.4035.yahoomailclas...@web29002.mail.ird.yahoo.com> >Content-Type: text/plain; charset="utf-8" > >ccie voice urban legend > >--- On Fri, 1/7/11, Cristobal Priego wrote: > > >From: Cristobal Priego >Subject: Re: [OSL | CCIE_Voice] B-ACD Drop Through >To: "Pablo Meneses" >Cc: "ccie voice" >Date: Friday, 1 July, 2011, 23:44 > > >i don't think that;s configurable > > >2011/6/30 Pablo Meneses > >Hi experts, > >Is there a way to display "1 call on phone" when using B-ACD Drop Through? > >I think that it will display "1 call on queue" and that there is no way for it >to display "1 call on phone", but, I better ask. > >Regards, > >-Pablo Meneses. > >___ >For more information regarding industry leading CCIE Lab training, please >visit www.ipexpert.com > >Are you a CCNP or CCIE and looking for a job? Check out >www.PlatinumPlacement.com > > >-Inline Attachment Follows- > > >___ >For more information regarding industry leading CCIE Lab training, please >visit www.ipexpert.com
[OSL | CCIE_Voice] CUE MWI
Hi All, I am using NME-CUE 7.0.5 Integrated with CallManager 7.0.2 in Home Lab. During the testsing i face a issue with "MWI OFF" it only work if i delete or save the voicemail. In case i read it & don't save or delete it, MWI status shown "RED" & after going to VM of user, it say you have "1 new message" . Is it normal behaviour ? Is somebody came across this issue before ? Config of CUE :- ccn subsystem sip gateway address "10.10.30.1" mwi sip unsolicited end subsystem Config at GW:- sip-ua mwi-server ipv4:10.10.30.2 expires 3600 port 5060 transport udp unsolicite. Ephone-Dn contain MWI sip command. Thanks&Rgds Deepak Sidana. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] HQ Phones not Registering
Hi Vinay, Please share the config of HQ Router & Switch Thanks&Rgds Deepak Sidana. From: Vinay Kumar6 To: ccie_voice@onlinestudylist.com Sent: Thursday, 16 June 2011 6:39 PM Subject: [OSL | CCIE_Voice] HQ Phones not Registering Hi, Facing difficulty in registering the HQ Phones to CUCM, Routing is enabled on the HQ router and Vlans are created on the switch. Phones are able to get the IP address from the CUCM (DHCP) server., Not sure what exactly to check for. Warm Regards, Vinay Kumar ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] T1 Pri Issue
Thanx all, for your valuable inputs. The issue is solved, my GW is registered with CCM. Earlier i was reactivating "mgcp bind media source-interface loop0" & mgcp & isdn l3-binding ccm-manager It work for me by reactivating "mgcp bind control source-interface loop0" Thanks again for your support, cheers :) Thanks&Rgds Deepak Sidana. ____ From: Joli-coeur Wouter To: Deepak sidana Cc: "ccie_voice@onlinestudylist.com" Sent: Fri, 7 January, 2011 4:07:17 AM Subject: Re: [OSL | CCIE_Voice] T1 Pri Issue There is not enough info here to troubleshoot this issue. Post full config of br1and pstn router and tell us what you have configured in cucm and what your goal is. Your controller config is not matching your serial interface number. Controller 0/0/1 Serial interface 0/0/0 Reg, Jolicoeur wouter Sent from my iPad On Jan 6, 2011, at 22:24, Deepak sidana wrote: Hi All, > >I am trying to connect the T1 from Br1-RTR to PSTN-WAN. Only when i use >service >mgcp, under controller, layer 2 isdn staus as TEI_ASSIGNED. > >At PSTN-WAN Router, i am using "isdn protocol-emulate network" under s0/0/0:23 > >Branch1 Config:- > >BR1-RTR#sh isdn sta >Global ISDN Switchtype = primary-net5 >ISDN Serial0/0/0:23 interface > dsl 0, interface ISDN Switchtype = primary-net5 > Layer 1 Status: > ACTIVE > Layer 2 Status: > TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED > >! >controller T1 0/0/1 > framing esf > linecode b8zs > cablelength long 0db >! >interface Serial0/0/0:23 > no ip address > encapsulation hdlc > isdn switch-type primary-net5 > isdn bind-l3 ccm-manager > isdn incoming-voice voice > no cdp enable > >Please share you experince, if some one faced the same issue. > Thanks&Rgds >Deepak Sidana. > > ___ >For more information regarding industry leading CCIE Lab training, please >visit >www.ipexpert.com > ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] T1 Pri Issue
Hi All, I am trying to connect the T1 from Br1-RTR to PSTN-WAN. Only when i use service mgcp, under controller, layer 2 isdn staus as TEI_ASSIGNED. At PSTN-WAN Router, i am using "isdn protocol-emulate network" under s0/0/0:23 Branch1 Config:- BR1-RTR#sh isdn sta Global ISDN Switchtype = primary-net5 ISDN Serial0/0/0:23 interface dsl 0, interface ISDN Switchtype = primary-net5 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED ! controller T1 0/0/1 framing esf linecode b8zs cablelength long 0db ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn bind-l3 ccm-manager isdn incoming-voice voice no cdp enable Please share you experince, if some one faced the same issue. Thanks&Rgds Deepak Sidana. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] HWIC-4ESW POE issue
Thanks All for your inputs. BR Deepak From: Sivakumar Mahalingam To: Damon Chaput Cc: ccie_voice@onlinestudylist.com Sent: Fri, 25 June, 2010 1:17:45 AM Subject: Re: [OSL | CCIE_Voice] HWIC-4ESW POE issue Just go with the 7900 series cisco power suppies for the phones.Its very cheap and below is the link. http://www.cablesandkits.com/cisco-7900-series-phone-power-supply-cppwrcube-p-49.html hth simah. On Thu, Jun 24, 2010 at 4:10 PM, Damon Chaput wrote: You will need to correct PS as well. For example, if you have a 2811 you would need the PWR-2811-IP= + the POE daughter card. > >Thanks, >Damon Chaput >Telecommunications Engineer >1-800 Contacts >(801) 316-7855 Desk >(801) 891-8525 Mobile >dcha...@1800contacts.com >From:ccie_voice-boun...@onlinestudylist.com >[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Deepak sidana >Sent: Thursday, June 24, 2010 1:46 PM >To: ccie_voice@onlinestudylist.com >Subject: [OSL | CCIE_Voice] HWIC-4ESW POE issue > >Hi All, > >I am in process of setting home lab, i am facing a problem with "HWIC-4ESW". >I have crated L2 & L3 vlans(vlan 200,400) on BR-II Router. & configure the >ports >with following commands. > >switchport trunk native vlan 200 > switchport mode trunk > switchport voice vlan 400 > >i have also tried "pppoe enable" command under interface, but its also not >helpul. > >When i plug the IP Phone, it does't recive the power,so vlan does't come up.If >i >plug my laptop driectly to port >it work fine. > >Please suggest how to make the "HWIC-4ESW" Power enabled. > >BR >Deepak > > >___ >For more information regarding industry leading CCIE Lab training, please >visit >www.ipexpert.com > > ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] HWIC-4ESW POE issue
Hi All, I am in process of setting home lab, i am facing a problem with "HWIC-4ESW". I have crated L2 & L3 vlans(vlan 200,400) on BR-II Router. & configure the ports with following commands. switchport trunk native vlan 200 switchport mode trunk switchport voice vlan 400 i have also tried "pppoe enable" command under interface, but its also not helpul. When i plug the IP Phone, it does't recive the power,so vlan does't come up.If i plug my laptop driectly to port it work fine. Please suggest how to make the "HWIC-4ESW" Power enabled. BR Deepak ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Call Routing Question
Thanks Bill I got something on "Route pattern wildcards" in CIPT-I book. + Matches one or more occurrences of any digit that matches the previous wildcard Looking for more explanation on this, as its look confusing to me. If i create route pattern of 51[23]+ & dial 51234, What will be the behaviour? Rgds Deepak Sidana. From: Bill Hatcher To: Deepak sidana ; ccie_voice@onlinestudylist.com Sent: Thursday, 30 July, 2009 12:46:44 PM Subject: Re: [OSL | CCIE_Voice] Call Routing Question the + is the international escape code. It is used to represent 001, 011, 00 depending on what country you live in. On Thu, Jul 30, 2009 at 10:05 AM, Deepak sidana wrote: > >Hi All, > >I was going through the wildcards under Call Routing. > >I have following question. > >What Wildcard “+” means & how it works in route pattern? > >If I have to dial 521234(PSTN) from CUCM, how can I use route pattern with “+” >wildcard? > >Regards, >Deepak. > Love Cricket? Check out live scores, photos, video highlights and more. Click here. >___ >For more information regarding industry leading CCIE Lab training, please >visit www.ipexpert.com > > See the Web's breaking stories, chosen by people like you. Check out Yahoo! Buzz. http://in.buzz.yahoo.com/___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Call Routing Question
Hi All, I was going through the wildcards under Call Routing. I have following question. What Wildcard “+” means & how it works in route pattern? If I have to dial 521234(PSTN) from CUCM, how can I use route pattern with “+” wildcard? Regards, Deepak. Yahoo! recommends that you upgrade to the new and safer Internet Explorer 8. http://downloads.yahoo.com/in/internetexplorer/___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Test to all OSL Mailing Lists
got it Thanks&Rgds Deepak Sidana. +919312724965 From: Mark Snow To: CCIE Voice Maillist ; ccie...@onlinestudylist.com; ccie...@onlinestudylist.com; CCIE Security Maillist Sent: Tuesday, 14 July, 2009 8:34:08 PM Subject: [OSL | CCIE_Voice] Test to all OSL Mailing Lists OSL Voice, RS, Security, and SP constituents, As many of you now know, some changes were made Friday night (without being tested) that caused mail service to be interrupted over the weekend. Those responsible (not me - I just got the privilege of having to FIX it :) have been drug into a back alley and promptly dispatched of. Anyway - big test message to see if mail is processing correctly. If you do get this message, REPLY TO ALL - that way all of the messages float through the OSL mail server and we can confirm in a larger way that mail is back up properly. Thanks! -- Mark Snow CCIE #14073 (Voice, Security) Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.309.413.4097 Mailto: ms...@ipexpert.com -- Join our free online support and peer group communities: http://www.IPexpert.com/communities -- IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. -- Love Cricket? Check out live scores, photos, video highlights and more. Click here http://cricket.yahoo.com___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] CUCM7.0 Beta Version Service not getting started
Thanks Basant! Upgrading the RAM to 4GB for server work for me. But i did it once, now set server back to 2GB & working fine now:) Deepak. From: basant yadav To: Deepak sidana Cc: ccievoice Sent: Tuesday, 7 July, 2009 11:29:47 PM Subject: Re: [OSL | CCIE_Voice] CUCM7.0 Beta Version Service not getting started Hi Deepak Pls check if you have "Software feature license" or not. Without this license, Call Manager service won't start. HTH - Basant On Tue, Jul 7, 2009 at 7:34 PM, Deepak sidana wrote: Hi Guys, > >I have installed the CUCM7.0 Beta version,on VMware with 2GB RAM & 65GB of HDD. >I am trying to start callmanager or any other service, after a long delay its >return with error "start failed" >Its having 3 Node License & 150 Device Liecenes. >I have tried to start services with IE8.0 & Safari too, but no luck. >Thanks in advance for your replies.. > >Deepak > > > > > See the Web's breaking stories, chosen by people like you. Check out Yahoo! Buzz. >___ >For more information regarding industry leading CCIE Lab training, please >visit www.ipexpert.com > > Send free SMS to your Friends on Mobile from your Yahoo! Messenger. Download Now! http://messenger.yahoo.com/download.php___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] CUCM7.0 Beta Version Service not getting started
Hi Guys, I have installed the CUCM7.0 Beta version,on VMware with 2GB RAM & 65GB of HDD. I am trying to start callmanager or any other service, after a long delay its return with error "start failed" Its having 3 Node License & 150 Device Liecenes. I have tried to start services with IE8.0 & Safari too, but no luck. Thanks in advance for your replies.. Deepak Looking for local information? Find it on Yahoo! Local http://in.local.yahoo.com/___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] ISDN CCBs
Hi, Can someone explain what is CCBs in ISDN? I have identical routers running the same ios, but one of my router show when PSTN call are active as =CCB:callid=7D74, sapi=0, ces=0, B-chan=6, calltype=VOICE but it also show=CCB:callid=7D96, sapi=0, ces=0 calltype=SIGNALING(wat this mean) I am wondreing its not showing calltype=SIGNALING on another router with identical setup. here is the output of l3 "sh isdn status" Layer 3 Status: > > 24 Active Layer 3 Call(s) > > CCB:callid=6407, sapi=0, ces=0, B-chan=8, calltype=VOICE > > CCB:callid=65EB, sapi=0, ces=0, B-chan=29, calltype=VOICE > > CCB:callid=65F4, sapi=0, ces=0, B-chan=3, calltype=VOICE > > CCB:callid=6611, sapi=0, ces=0, B-chan=12, calltype=VOICE > > CCB:callid=66AC, sapi=0, ces=0, B-chan=28, calltype=VOICE > > CCB:callid=682D, sapi=0, ces=0, B-chan=20, calltype=VOICE > > CCB:callid=6834, sapi=0, ces=0, B-chan=23, calltype=VOICE > > CCB:callid=6950, sapi=0, ces=0, B-chan=31, calltype=VOICE > > CCB:callid=6956, sapi=0, ces=0, B-chan=4, calltype=VOICE > > CCB:callid=695F, sapi=0, ces=0, B-chan=21, calltype=VOICE > > CCB:callid=6979, sapi=0, ces=0, B-chan=1, calltype=VOICE > > CCB:callid=6B8F, sapi=0, ces=0, B-chan=7, calltype=VOICE > > CCB:callid=E77C, sapi=0, ces=0, B-chan=22, calltype=VOICE > > CCB:callid=73AB, sapi=0, ces=0, B-chan=27, calltype=VOICE > > CCB:callid=73AF, sapi=0, ces=0, B-chan=19, calltype=VOICE > > CCB:callid=E822, sapi=0, ces=0, B-chan=30, calltype=VOICE > > CCB:callid=79D8, sapi=0, ces=0, B-chan=13, calltype=VOICE > > CCB:callid=7A9A, sapi=0, ces=0, B-chan=24, calltype=VOICE > > CCB:callid=7AB6, sapi=0, ces=0, B-chan=25, calltype=VOICE > > CCB:callid=7B1F, sapi=0, ces=0, B-chan=9, calltype=VOICE > > CCB:callid=7BD6, sapi=0, ces=0, B-chan=15, calltype=VOICE > > CCB:callid=7C23, sapi=0, ces=0, B-chan=5, calltype=VOICE > > CCB:callid=7D07, sapi=0, ces=0, B-chan=10, calltype=VOICE > > CCB:callid=7D27, sapi=0, ces=0, B-chan=14, calltype=VOICE > > CCB:callid=7D2C, sapi=0, ces=0, B-chan=26, calltype=VOICE > > CCB:callid=7D73, sapi=0, ces=0, B-chan=2, calltype=VOICE > > CCB:callid=7D74, sapi=0, ces=0, B-chan=6, calltype=VOICE > > CCB:callid=7D96, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7D97, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7D98, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7D99, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7D9E, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7D9F, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA0, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA1, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA2, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA3, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA4, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA5, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA6, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA7, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA8, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DA9, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DAA, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DAB, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DAC, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DB9, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DBA, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DBB, sapi=0, ces=0, B-chan=11, calltype=VOICE > > CCB:callid=7DBC, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DBD, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DBE, sapi=0, ces=0 calltype=SIGNALING > > CCB:callid=7DBF, sapi=0, ces=0 calltype=SIGNALING > > Active dsl 0 CCBs = 53 > > The Free Channel Mask: 0x8003 > > Number of L2 Discards = 0, L2 Session ID = 0 > Regards Deepak Bollywood news, movie reviews, film trailers and more! Go to http://in.movies.yahoo.com/