Add 'frame-relay map ip ' statements as well as the 'frame-relay map
clns' statements and it will resolve your problem.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: Thursday, January 24, 2002 4:11 PM
To: [EMAIL PROTECTED]
Subject: Re: ISIS [7:33096]
James,
OK, you tried the map statements with the broadcast keyword on the hub. Did
you add the broadcast keyword on the map statements between the spoke sites?
Regards,
Scott
James Haynes wrote:
>
> Scott,
>
> Thanks for your help. I had already tried the frame-relay map
> commands with
> the broadcast ending. It didn't seem to work then either :(
> You are correct in that on a multi-access LAN all the routers
> have to see
> each other and these two spoke routers are definitely not. The
> DIS is not
> quite the same as the DR in OSPF and advertises a pseudonode
> (the network)
> to all attached routers. Thanks for your help I'm going to keep
> trying.
>
> --
> James Haynes
> Network Architect
> Cendant IT
> A+,MCSE,CCNA,CCDA,CCNP,CCDP,
> CQS-SNA/IPSS
>
> ""s vermill"" wrote in message
> [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > James,
> >
> > I hate to give such a poorly researched answer, but I did
> quite a bit of
> > experimenting with ISIS a few months back. I don't have time
> to verify
> this
> > for sure right now, but here is what I remember:
> >
> > ISIS knows nothing of NBMA. It only know serial
> point-to-point and
> > multi-access LANs. So I would replace those interface-dlci
> statements on
> > your hub with frame-relay map ip statements and I would also
> add the
> > broadcast keyword to EVERYTHING. I don't remember all of the
> nuances of
> DIS
> > vs. DR, but I do seem to recall that in a broadcast LAN
> environment, all
> > routers need to see one another. I am fairly sure that there
> are subtle
> but
> > important differences in the way an ISIS LAN and an OSPF LAN
> behave.
> >
> > If this doesn't work, I'll make some time to try to refresh
> my memory.
> >
> > Regards,
> >
> > Scott
> >
> >
> > James Haynes wrote:
> > >
> > > I've been working on a home lab scenario involving ISIS and
> > > it's been
> > > driving me crazy. The behavior appears to be a split
> horizion
> > > issue even
> > > though ISIS(like OSPF) is a link state protocol and
> shouldn't
> > > have a problem
> > > with this. The scenario involves a hub router R4 and two
> spoke
> > > routers
> > > r2,r3. R4 is connected via a multipoint sub-interface to the
> > > physical frame
> > > relay interfaces on r2 and r3. There a various routers
> behind
> > > both of the
> > > spoke routers and the hub router. R4 sees all routes on the
> > > network as do
> > > the routers located behind R4. R2 see's all routes on the
> > > network except
> > > those behind r3 and r3 sees all routes except for those
> behind
> > > r2. In this
> > > setup ISIS sends out multicasted LAN hellos that are picked
> up
> > > by other
> > > routers.
> > > I thought perhaps that like the OSPF neighbor command that
> I've
> > > used in hub
> > > and spoke setup's I could use the clns is-neighbor interface
> > > command, but
> > > all I get are messages saying you cannot put static IS or ES
> > > mappings on a
> > > Frame Relay interface. Anyway, what follows are the relevant
> > > config's. I was
> > > hoping someone may spot something I haven't seen.
> > >
> > > R4#
> > >
> > > interface Serial0.2 multipoint
> > > ip address 10.10.234.4 255.255.255.240
> > > no ip directed-broadcast
> > > ip router isis 0
> > > no ip split-horizon
> > > clns router isis 0
> > > isis priority 127
> > > frame-relay map clns 102 broadcast
> > > frame-relay map clns 103 broadcast
> > > frame-relay interface-dlci 102
> > > frame-relay interface-dlci 103
> > >
> > >
> > >
> > > router isis 0
> > > net 49....0004.00
> > >
> > >
> > > r2#
> > >
> > > interface Serial1/0
> > > ip address 10.10.234.2 255.255.255.240
> > > ip router isis 0
> > > encapsulation frame-relay
> > > clns router isis 0
> > > frame-relay map clns 104 broadcast
> > > frame-relay map ip 10.10.234.3 104
> > > frame-relay map ip 10.10.234.4 104 broadcast
> > >
> > > router isis 0
> > > net 49....0002.00
> > >
> > >
> > > r3#
> > >
> > > interface Serial1/0
> > > ip address 10.10.234.3 255.255.255.240
> > > ip router isis 0
> > > encapsulation frame-relay
> > > clns router isis 0
> > > frame-relay map clns 104 broadcast
> > > frame-relay map ip 10.10.234.2 104
> > > frame-relay map ip 10.10.234.4 104 broadcast
> > >
> > >
> > > router isis 0
> > > net 49....0003.00
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > --
> > > James Haynes
> > > Network Architect
> > > Cendant IT
> > > A+,MCSE,CCNA,CCDA,CCNP,CCDP,
> > > CQS-SNA/IPSS
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=33126&t=33096
--
FAQ, list ar