RE: Router crash - what does output mean

[Peter Ching]

I think you'll need to open a Cisco TAC case for this one,
but send the 'show stack' and 'show version'

-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Andrew Larkins
Sent: Monday, 19 February 2001 8:33 PM
To: Cisco Mail List
Subject: Router crash - what does output mean
Importance: High


Hi all,

Our Cisco 3640 router at the DRP site crashed. Router was in "rommon1" when
I got there. By pressing "i", the router rebooted and came up fine.
The output of the show ver is below. What does the error message mean - does
it (PC 0x603503CC) point to a specific cause..?

ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY DEPLOYMENT
RELEASE SOFTWARE (fc2)

xx uptime is 48 minutes
System returned to ROM by error - a Software forced crash, PC 0x603503CC
System image file is "flash:c3640-ds-mz.121-5a.bin"

cisco 3640 (R4700) processor (revision 0x00) with 60416K/5120K bytes of
memory.
Processor board ID 06014488
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Basic Rate ISDN software, Version 1.1.
2 Ethernet/IEEE 802.3 interface(s)
2 Token Ring/IEEE 802.5 interface(s)
4 Serial network interface(s)
8 Low-speed serial(sync/async) network interface(s)
4 ISDN Basic Rate interface(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102


Thanks
Andrew Larkins
BCom, CCNA, CCDA
Bytes Technology Group
Tel: +2711 800-9300
Fax: +2711 800-9496
Cell: +2783-656-7214
Email: [EMAIL PROTECTED]
OR  [EMAIL PROTECTED]


"This message may contain information which is confidential and subject to
legal privilege.  If you are not the intended recipient, you may not peruse,
use, disseminate, distribute or copy this message.  If you have received
this message in error, please notify the sender immediately by email,
facsimile or telephone and return and/or destroy the original message."


_
FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]

_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]

RE: Looped

[Peter Ching]

Check your configuration if you're running an integrated csu/dsu that
you don't have a 'loopback' command configured. If you're running an
external csu/dsu, check that you don't have a local loopback or loopback
dte.
If the above are negative, speak to your telco and see that they have a
loop installed on your circuit.

 -Original Message-
 From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
 Thomas
 Sent: Monday, 19 February 2001 5:54 PM
 To: [EMAIL PROTECTED]
 Subject: Looped


 Hi All - I am bringing up a frame circuit from a remote site.
  However, I
 couldn't get the line up since it is looped.  When I do the
 "show int s0/0",
 I got "Protocol is up, line is down (looped).  I checked all
 the setting and
 didn't see any wrong.  Can this be a mistake on the ISP side,
 or something
 wrong with my configuration? I am running 12.1 on the Cisco
 2600 router.
 Any hint woule be appreciated!!!


 _
 FAQ, list archives, and subscription info:
 http://www.groupstudy.com/list/cisco.html
 Report misconduct and Nondisclosure violations to
 [EMAIL PROTECTED]

_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]