RE: FastEthernet Adapter for 7206 - How do I enable? [7:6411]
I threw out that response because I saw for example that the pa-8e with a rev below 1.14, altho fine on a 7206, is problematic on a vxr. I was not sure which 7206 flavor was being discussed. Brian Sonic Whalen Success = Preparation + Opportunity On Fri, 1 Jun 2001, Daniel Cotts wrote: The PA-2FE is supported in Cisco IOS Releases 12.1(5)E, 12.0(15)S, 12.1(6), 12.2(1), 12.2(2)T and after. HTH -Original Message- From: Brian [mailto:[EMAIL PROTECTED]] Sent: Friday, June 01, 2001 8:57 PM To: [EMAIL PROTECTED] Subject: Re: FastEthernet Adapter for 7206 - How do I enable? [7:6411] ancient hardware rev?? Brian Sonic Whalen Success = Preparation + Opportunity On Wed, 30 May 2001, Robert Fowler wrote: Hello, I've been beating my head on the side of this router. I've searched the CCO on how to enable the PA-2FE adapter, and found some information on microcode. Then I found out the IOS I've upgraded to (12.1.(3)) already has a current version built in. I don't recall learning anything about Microcode in any of my studying. How does it differ from the IOS? Anyway, the adapter card will not enable, and when I do a show diag 1 I get this:(see below) show that it is powered off. I've searched everywhere to find the command to power it on. Any suggestions? Slot 1: Unknown (type 548) Port adapter Port adapter is disabled deactivated powered off Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision: 1.0 PCB Serial Number: MIC0516000Y Part Number : 73-5419-06 Board Revision : A0 RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Deviation Number : 0-0 Model: PA-2FE-TX Part Number : 800-08350-06 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 02 24 41 01 00 C1 8B 4D 49 43 30 35 31 0x10: 36 30 30 30 59 82 49 15 2B 06 42 41 30 03 00 81 0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D 0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20 0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF Thank You, Robert Fowler Network Administrator MasTec, Inc. Office: 305.406.3150 Fax: 305.599.7085 Email: mailto:[EMAIL PROTECTED] MasTec Building the e-World Confidentiality Notice: The information contained in this transmittal, including any attachment, is privileged and confidential information and is intended only for the person or entity to which it is addressed. If you are neither the intended recipient nor the employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any disclosure, copying or distribution or the taking of any action in reliance on the contents of this transmittal is strictly prohibited. If you have received this transmittal in error, please contact the sender immediately and delete this transmittal from any computer or other data bank. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=6949t=6411 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: FastEthernet Adapter for 7206 - How do I enable? [7:6411]
ancient hardware rev?? Brian Sonic Whalen Success = Preparation + Opportunity On Wed, 30 May 2001, Robert Fowler wrote: Hello, I've been beating my head on the side of this router. I've searched the CCO on how to enable the PA-2FE adapter, and found some information on microcode. Then I found out the IOS I've upgraded to (12.1.(3)) already has a current version built in. I don't recall learning anything about Microcode in any of my studying. How does it differ from the IOS? Anyway, the adapter card will not enable, and when I do a show diag 1 I get this:(see below) show that it is powered off. I've searched everywhere to find the command to power it on. Any suggestions? Slot 1: Unknown (type 548) Port adapter Port adapter is disabled deactivated powered off Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision: 1.0 PCB Serial Number: MIC0516000Y Part Number : 73-5419-06 Board Revision : A0 RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Deviation Number : 0-0 Model: PA-2FE-TX Part Number : 800-08350-06 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 02 24 41 01 00 C1 8B 4D 49 43 30 35 31 0x10: 36 30 30 30 59 82 49 15 2B 06 42 41 30 03 00 81 0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D 0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20 0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF Thank You, Robert Fowler Network Administrator MasTec, Inc. Office: 305.406.3150 Fax: 305.599.7085 Email: mailto:[EMAIL PROTECTED] MasTec Building the e-World Confidentiality Notice: The information contained in this transmittal, including any attachment, is privileged and confidential information and is intended only for the person or entity to which it is addressed. If you are neither the intended recipient nor the employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any disclosure, copying or distribution or the taking of any action in reliance on the contents of this transmittal is strictly prohibited. If you have received this transmittal in error, please contact the sender immediately and delete this transmittal from any computer or other data bank. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=6847t=6411 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: FastEthernet Adapter for 7206 - How do I enable? [7:6411]
The PA-2FE is supported in Cisco IOS Releases 12.1(5)E, 12.0(15)S, 12.1(6), 12.2(1), 12.2(2)T and after. HTH -Original Message- From: Brian [mailto:[EMAIL PROTECTED]] Sent: Friday, June 01, 2001 8:57 PM To: [EMAIL PROTECTED] Subject: Re: FastEthernet Adapter for 7206 - How do I enable? [7:6411] ancient hardware rev?? Brian Sonic Whalen Success = Preparation + Opportunity On Wed, 30 May 2001, Robert Fowler wrote: Hello, I've been beating my head on the side of this router. I've searched the CCO on how to enable the PA-2FE adapter, and found some information on microcode. Then I found out the IOS I've upgraded to (12.1.(3)) already has a current version built in. I don't recall learning anything about Microcode in any of my studying. How does it differ from the IOS? Anyway, the adapter card will not enable, and when I do a show diag 1 I get this:(see below) show that it is powered off. I've searched everywhere to find the command to power it on. Any suggestions? Slot 1: Unknown (type 548) Port adapter Port adapter is disabled deactivated powered off Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision: 1.0 PCB Serial Number: MIC0516000Y Part Number : 73-5419-06 Board Revision : A0 RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Deviation Number : 0-0 Model: PA-2FE-TX Part Number : 800-08350-06 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 02 24 41 01 00 C1 8B 4D 49 43 30 35 31 0x10: 36 30 30 30 59 82 49 15 2B 06 42 41 30 03 00 81 0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D 0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20 0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF Thank You, Robert Fowler Network Administrator MasTec, Inc. Office: 305.406.3150 Fax: 305.599.7085 Email: mailto:[EMAIL PROTECTED] MasTec Building the e-World Confidentiality Notice: The information contained in this transmittal, including any attachment, is privileged and confidential information and is intended only for the person or entity to which it is addressed. If you are neither the intended recipient nor the employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any disclosure, copying or distribution or the taking of any action in reliance on the contents of this transmittal is strictly prohibited. If you have received this transmittal in error, please contact the sender immediately and delete this transmittal from any computer or other data bank. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=6850t=6411 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: FastEthernet Adapter for 7206 - How do I enable? [7:6411]
Checkout the HW-SW Compatibility Table http://www.cisco.com/cgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi The PA-2FE-TX requires a minimum of 12.1(6) for Mainline. David C Prall [EMAIL PROTECTED] http://dcp.dcptech.com - Original Message - From: Robert Fowler To: Sent: Wednesday, May 30, 2001 8:36 AM Subject: FastEthernet Adapter for 7206 - How do I enable? [7:6411] Hello, I've been beating my head on the side of this router. I've searched the CCO on how to enable the PA-2FE adapter, and found some information on microcode. Then I found out the IOS I've upgraded to (12.1.(3)) already has a current version built in. I don't recall learning anything about Microcode in any of my studying. How does it differ from the IOS? Anyway, the adapter card will not enable, and when I do a show diag 1 I get this:(see below) show that it is powered off. I've searched everywhere to find the command to power it on. Any suggestions? Slot 1: Unknown (type 548) Port adapter Port adapter is disabled deactivated powered off Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision: 1.0 PCB Serial Number: MIC0516000Y Part Number : 73-5419-06 Board Revision : A0 RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Deviation Number : 0-0 Model: PA-2FE-TX Part Number : 800-08350-06 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 02 24 41 01 00 C1 8B 4D 49 43 30 35 31 0x10: 36 30 30 30 59 82 49 15 2B 06 42 41 30 03 00 81 0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D 0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20 0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF Thank You, Robert Fowler Network Administrator MasTec, Inc. Office: 305.406.3150 Fax: 305.599.7085 Email: mailto:[EMAIL PROTECTED] MasTec Building the e-World Confidentiality Notice: The information contained in this transmittal, including any attachment, is privileged and confidential information and is intended only for the person or entity to which it is addressed. If you are neither the intended recipient nor the employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any disclosure, copying or distribution or the taking of any action in reliance on the contents of this transmittal is strictly prohibited. If you have received this transmittal in error, please contact the sender immediately and delete this transmittal from any computer or other data bank. FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=6415t=6411 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: FastEthernet Adapter for 7206 - How do I enable? [7:6411]
Hmm I didn't find that on the HW-SW matrix. As a matter a fact I couldn't find PA-2FE-TX, only PA-2FEISL-TX and PA-FE-FX, both of which supported 12.1(3). Robert -Original Message- From: David C Prall [mailto:[EMAIL PROTECTED]] Sent: Wednesday, May 30, 2001 9:04 AM To: [EMAIL PROTECTED] Subject: Re: FastEthernet Adapter for 7206 - How do I enable? [7:6411] Checkout the HW-SW Compatibility Table http://www.cisco.com/cgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi The PA-2FE-TX requires a minimum of 12.1(6) for Mainline. David C Prall [EMAIL PROTECTED] http://dcp.dcptech.com - Original Message - From: Robert Fowler To: Sent: Wednesday, May 30, 2001 8:36 AM Subject: FastEthernet Adapter for 7206 - How do I enable? [7:6411] Hello, I've been beating my head on the side of this router. I've searched the CCO on how to enable the PA-2FE adapter, and found some information on microcode. Then I found out the IOS I've upgraded to (12.1.(3)) already has a current version built in. I don't recall learning anything about Microcode in any of my studying. How does it differ from the IOS? Anyway, the adapter card will not enable, and when I do a show diag 1 I get this:(see below) show that it is powered off. I've searched everywhere to find the command to power it on. Any suggestions? Slot 1: Unknown (type 548) Port adapter Port adapter is disabled deactivated powered off Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision: 1.0 PCB Serial Number: MIC0516000Y Part Number : 73-5419-06 Board Revision : A0 RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Deviation Number : 0-0 Model: PA-2FE-TX Part Number : 800-08350-06 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 02 24 41 01 00 C1 8B 4D 49 43 30 35 31 0x10: 36 30 30 30 59 82 49 15 2B 06 42 41 30 03 00 81 0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D 0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20 0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF Thank You, Robert Fowler Network Administrator MasTec, Inc. Office: 305.406.3150 Fax: 305.599.7085 Email: mailto:[EMAIL PROTECTED] MasTec Building the e-World Confidentiality Notice: The information contained in this transmittal, including any attachment, is privileged and confidential information and is intended only for the person or entity to which it is addressed. If you are neither the intended recipient nor the employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any disclosure, copying or distribution or the taking of any action in reliance on the contents of this transmittal is strictly prohibited. If you have received this transmittal in error, please contact the sender immediately and delete this transmittal from any computer or other data bank. FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=6441t=6411 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: FastEthernet Adapter for 7206 - How do I enable? [7:6411]
David, My sincerest apologies for ever doubting you. 12.1(6) works great! Thanks, Robert -Original Message- From: David C Prall [mailto:[EMAIL PROTECTED]] Sent: Wednesday, May 30, 2001 9:04 AM To: [EMAIL PROTECTED] Subject: Re: FastEthernet Adapter for 7206 - How do I enable? [7:6411] Checkout the HW-SW Compatibility Table http://www.cisco.com/cgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi The PA-2FE-TX requires a minimum of 12.1(6) for Mainline. David C Prall [EMAIL PROTECTED] http://dcp.dcptech.com - Original Message - From: Robert Fowler To: Sent: Wednesday, May 30, 2001 8:36 AM Subject: FastEthernet Adapter for 7206 - How do I enable? [7:6411] Hello, I've been beating my head on the side of this router. I've searched the CCO on how to enable the PA-2FE adapter, and found some information on microcode. Then I found out the IOS I've upgraded to (12.1.(3)) already has a current version built in. I don't recall learning anything about Microcode in any of my studying. How does it differ from the IOS? Anyway, the adapter card will not enable, and when I do a show diag 1 I get this:(see below) show that it is powered off. I've searched everywhere to find the command to power it on. Any suggestions? Slot 1: Unknown (type 548) Port adapter Port adapter is disabled deactivated powered off Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision: 1.0 PCB Serial Number: MIC0516000Y Part Number : 73-5419-06 Board Revision : A0 RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Deviation Number : 0-0 Model: PA-2FE-TX Part Number : 800-08350-06 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 02 24 41 01 00 C1 8B 4D 49 43 30 35 31 0x10: 36 30 30 30 59 82 49 15 2B 06 42 41 30 03 00 81 0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D 0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20 0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF Thank You, Robert Fowler Network Administrator MasTec, Inc. Office: 305.406.3150 Fax: 305.599.7085 Email: mailto:[EMAIL PROTECTED] MasTec Building the e-World Confidentiality Notice: The information contained in this transmittal, including any attachment, is privileged and confidential information and is intended only for the person or entity to which it is addressed. If you are neither the intended recipient nor the employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any disclosure, copying or distribution or the taking of any action in reliance on the contents of this transmittal is strictly prohibited. If you have received this transmittal in error, please contact the sender immediately and delete this transmittal from any computer or other data bank. FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=6454t=6411 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
