VOIP over FR..how can get the tone from opposite PABX..?
I have scenario to install: Headquarter (HQ) connect to Branch A (A) and B (B) using Frame Relay HQ using E&M conect to PABX HQ and Branch A using E&M but Branch B using FXO. We make dial plane like this: x-111-yyy --> to HQ from the rest x-222-yyy --> to A from the rest x-333-yyy --> to B from the rest x = number that user must dial to get the tone from Voip configured in PABX yyy = local extension number. The problem is, when we dial from HQ to Branch A/B, we can only reach the user at the opposite site if we dial x-222-yyy / x-333-yyy all at once. We can not press x-222 to get the tone from PABX A and then extension number. How can we configure the router to enable user get the tone from opposite PABX after dial 111 or 222 or 333.? CONFIG in HQ dial-peer voice 1 pots destination-pattern 111 port 1/0/0 ! dial-peer voice 222 voip destination-pattern 222... session target ipv4:192.168.100.1 ! dial-peer voice 333 voip destination-pattern 333... ip precedence 5 session target ipv4:192.168.100.5 voice-port 1/0/0 timing percentbreak 50 operation 4-wire type 5 signal immediate regards Grad _ Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: VOIP over FR..how can get the tone from opposite PABX..?
I have just done the same thing few weeks ago. Make sure that you have the cables from PBX to E&M interfaces made by the Cisco specification. You can get the wiring details from the 1700 Series Hardware installation guide or the web. Cheers. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: VOIP over FR..how can get the tone from opposite PABX..?
Thanks, I have followed the cable specification from Cisco to E&M interface. But for the grounding, I stick the E&M grounding to Cisco chasis. SO, Is there anything left on the config..? regards Grad >From: "Igor Glavanic" <[EMAIL PROTECTED]> >Reply-To: "Igor Glavanic" <[EMAIL PROTECTED]> >To: [EMAIL PROTECTED] >Subject: Re: VOIP over FR..how can get the tone from opposite PABX..? >Date: Tue, 6 Mar 2001 16:20:43 +1100 > >I have just done the same thing few weeks ago. >Make sure that you have the cables from PBX to E&M interfaces made by the >Cisco specification. You can get the wiring details from the 1700 Series >Hardware installation guide or the web. > >Cheers. > > > >_ >FAQ, list archives, and subscription info: >http://www.groupstudy.com/list/cisco.html >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: VOIP over FR..how can get the tone from opposite PABX..?
[ The following text is in the "iso-8859-1" character set. ] [ Your display is set for the "US-ASCII" character set. ] [ Some characters may be displayed incorrectly. ] Hai Have the same problem last time, the tone and rinnging tone will be intermitten if you dont have the same grounding for both Router and PABX. Do have a same grounding point for both PABX and router. What i have done is make a temp cable from my PABX to the cisco chassis and you got tone. p/s good luck basar --- Grad Alfons Kanon <[EMAIL PROTECTED]> wrote: > Thanks, > > I have followed the cable specification from Cisco > to E&M interface. > But for the grounding, I stick the E&M grounding to > Cisco chasis. > > SO, Is there anything left on the config..? > > regards > > Grad > > > >From: "Igor Glavanic" <[EMAIL PROTECTED]> > >Reply-To: "Igor Glavanic" <[EMAIL PROTECTED]> > >To: [EMAIL PROTECTED] > >Subject: Re: VOIP over FR..how can get the tone > from opposite PABX..? > >Date: Tue, 6 Mar 2001 16:20:43 +1100 > > > >I have just done the same thing few weeks ago. > >Make sure that you have the cables from PBX to E&M > interfaces made by the > >Cisco specification. You can get the wiring details > from the 1700 Series > >Hardware installation guide or the web. > > > >Cheers. > > > > > > > >_ > >FAQ, list archives, and subscription info: > >http://www.groupstudy.com/list/cisco.html > >Report misconduct and Nondisclosure violations to > [EMAIL PROTECTED] > > _ > Get Your Private, Free E-mail from MSN Hotmail at > http://www.hotmail.com. > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] __ Do You Yahoo!? Yahoo! Auctions - Buy the things you want at great prices. http://auctions.yahoo.com/ _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]