deep trouble
hi friends I am in deep trouble. help required I am ravi kumar from HYDERABAD, INDIA i have a 2503 router in my office. recently we got ISDN connection from local basic telephone service provider (DOT) and bought ISDN internet account from local ISP. I want to provide internet access to all my staff through this router. i configured my router's BRI 0 port with following commands for DDR. 1)router# config terminal 2) ip route 0.0.0.0 0.0.0.0 bri 0 and 3) ip router 0.0.0.0 0.0.0.0 next hop count 3) dialer-list 4 protocol ip permit 4)interface bri 0 (i did not assign any ip address to bri port, since ISP server will give ip address to port once connection is established) 5) isdn switch type basic-net3 6) isdn spid1 <7digit number> 7) dialer-group 4 8) dialer map ip nexthopaddress numbertodial (basically ISP will give only phone number to dial. but by using isdn card in my pc and dialing to ISP, i got dial-up server ip address. i used this address as gateway address for my router) 9) encapsulation ppp 10) ppp authentication pap username xyz password abc 11) dialer idle-timout 30 after this i saved configuration and rebooted the router. if i run show ip interface, it is showing bri 0 is up and line protocol is up. but if i run show isdn status, it is showing bri 0 layer is deactivated and layer 1 is not active. my queries are 1) is this configuration is right or wrong? 2) if it is right, how it initiate the call to isp? 3) if it is not right, pls let me know step by step cofiguration to dialup ISP. your help in this regard is highly apprecaited. regards ravi kumar B. Get free email and a permanent address at http://www.netaddress.com/?N=1 ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: deep trouble
Title: RE: deep trouble You've got line problems.just by specifying the switch-type and plugging in the ISDN you should get layer 1 -Original Message- From: Ravi Kumar [mailto:[EMAIL PROTECTED]] Sent: Thursday, August 31, 2000 7:13 AM To: [EMAIL PROTECTED] Subject: deep trouble hi friends I am in deep trouble. help required I am ravi kumar from HYDERABAD, INDIA i have a 2503 router in my office. recently we got ISDN connection from local basic telephone service provider (DOT) and bought ISDN internet account from local ISP. I want to provide internet access to all my staff through this router. i configured my router's BRI 0 port with following commands for DDR. 1)router# config terminal 2) ip route 0.0.0.0 0.0.0.0 bri 0 and 3) ip router 0.0.0.0 0.0.0.0 next hop count 3) dialer-list 4 protocol ip permit 4)interface bri 0 (i did not assign any ip address to bri port, since ISP server will give ip address to port once connection is established) 5) isdn switch type basic-net3 6) isdn spid1 <7digit number> 7) dialer-group 4 8) dialer map ip nexthopaddress numbertodial (basically ISP will give only phone number to dial. but by using isdn card in my pc and dialing to ISP, i got dial-up server ip address. i used this address as gateway address for my router) 9) encapsulation ppp 10) ppp authentication pap username xyz password abc 11) dialer idle-timout 30 after this i saved configuration and rebooted the router. if i run show ip interface, it is showing bri 0 is up and line protocol is up. but if i run show isdn status, it is showing bri 0 layer is deactivated and layer 1 is not active. my queries are 1) is this configuration is right or wrong? 2) if it is right, how it initiate the call to isp? 3) if it is not right, pls let me know step by step cofiguration to dialup ISP. your help in this regard is highly apprecaited. regards ravi kumar B. Get free email and a permanent address at http://www.netaddress.com/?N=1 ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: deep trouble
Talk to the local telco about the type of interface you need. You may need a NT1 between your router's BRI (S/T interface) and the ISDN switch. Will "Ravi Kumar" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > hi friends > > I am in deep trouble. help required > > I am ravi kumar from HYDERABAD, INDIA > > i have a 2503 router in my office. recently we got ISDN connection from local > basic telephone service provider (DOT) and bought ISDN internet account from > local ISP. I want to provide internet access to all my staff through this > router. > > i configured my router's BRI 0 port with following commands for DDR. > > 1)router# config terminal > > 2) ip route 0.0.0.0 0.0.0.0 bri 0 > and > 3) ip router 0.0.0.0 0.0.0.0 next hop count > > 3) dialer-list 4 protocol ip permit > > 4)interface bri 0 > (i did not assign any ip address to bri port, since ISP server will give ip > address to port once connection is established) > > 5) isdn switch type basic-net3 > > 6) isdn spid1 <7digit number> > > 7) dialer-group 4 > > 8) dialer map ip nexthopaddress numbertodial > (basically ISP will give only phone number to dial. but by using isdn card in > my pc and dialing to ISP, i got dial-up server ip address. i used this address > as gateway address for my router) > > 9) encapsulation ppp > > 10) ppp authentication pap username xyz password abc > > 11) dialer idle-timout 30 > > after this i saved configuration and rebooted the router. > > if i run show ip interface, it is showing bri 0 is up and line protocol is > up. > but if i run show isdn status, it is showing bri 0 layer is deactivated and > layer 1 is not active. > > my queries are > > 1) is this configuration is right or wrong? > > 2) if it is right, how it initiate the call to isp? > > 3) if it is not right, pls let me know step by step cofiguration to dialup > ISP. > > your help in this regard is highly apprecaited. > > regards > ravi kumar B. > > > > > > Get free email and a permanent address at http://www.netaddress.com/?N=1 > > ___ > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html > FAQ, list archives, and subscription info: http://www.groupstudy.com > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: deep trouble
Check your switch type, too. I have no idea what is used in India, but basic-net3 over here doesn't use SPIDs. If your provider has given you a SPID to use, I suspect you've got the wrong switch-type configured. Check with your provider: basic-net3 is also known as ETSI or Euro-ISDN. If your switch-type is correct, check your cabling connections, and if they're OK tell your provider to fix the line. JMcL -- Forwarded by Jenny Mcleod/NSO/CSDA on 01/09/2000 08:58 am --- "Greene, Patrick" <[EMAIL PROTECTED]> on 31/08/2000 10:45:44 pm Please respond to "Greene, Patrick" <[EMAIL PROTECTED]> To: "'Ravi Kumar'" <[EMAIL PROTECTED]> [EMAIL PROTECTED] cc:(bcc: JENNY MCLEOD/NSO/CSDA) Subject: RE: deep trouble You've got line problems.just by specifying the switch-type and plugging in the ISDN you should get layer 1 -Original Message- From: Ravi Kumar [mailto:[EMAIL PROTECTED]] Sent: Thursday, August 31, 2000 7:13 AM To: [EMAIL PROTECTED] Subject: deep trouble hi friends I am in deep trouble. help required I am ravi kumar from HYDERABAD, INDIA i have a 2503 router in my office. recently we got ISDN connection from local basic telephone service provider (DOT) and bought ISDN internet account from local ISP. I want to provide internet access to all my staff through this router. i configured my router's BRI 0 port with following commands for DDR. 1)router# config terminal 2) ip route 0.0.0.0 0.0.0.0 bri 0 and 3) ip router 0.0.0.0 0.0.0.0 next hop count 3) dialer-list 4 protocol ip permit 4)interface bri 0 (i did not assign any ip address to bri port, since ISP server will give ip address to port once connection is established) 5) isdn switch type basic-net3 6) isdn spid1 <7digit number> 7) dialer-group 4 8) dialer map ip nexthopaddress numbertodial (basically ISP will give only phone number to dial. but by using isdn card in my pc and dialing to ISP, i got dial-up server ip address. i used this address as gateway address for my router) 9) encapsulation ppp 10) ppp authentication pap username xyz password abc 11) dialer idle-timout 30 after this i saved configuration and rebooted the router. if i run show ip interface, it is showing bri 0 is up and line protocol is up. but if i run show isdn status, it is showing bri 0 layer is deactivated and layer 1 is not active. my queries are 1) is this configuration is right or wrong? 2) if it is right, how it initiate the call to isp? 3) if it is not right, pls let me know step by step cofiguration to dialup ISP. your help in this regard is highly apprecaited. regards ravi kumar B. ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: deep trouble
At this point there are only three commands that will be of any use in troubleshooting the ISDN connection: First two: show controller bri show isdn status Show controller bri specifically looks at the "D" channel while show isdn status looks at all three layers. If layer one shows "deactivated", you are not even seeing the telco's isdn switch. Things to check: 1) Is the physical connection from your router wired corrrectly? 2) Who is suppling what interface (U or S/T). Do you need a NT1? After you have checked the above try "debug bri" (careful, this spits out a ton of info. Do a "no debug all" first). If you have an electrical connection to the switch, you should see some output from this command. (Make sure you do a "no debug all" when you are done. 3) Have you specified the correct switch type? Once you hace established Layer 1 and the "D" channel is up, you should be good. If not, you can then try "debug isdn q921" to check layer 2 negotiations and "debug isdn q931" for layer three. Good luck.. Ravi Kumar wrote: > hi friends > > I am in deep trouble. help required > > I am ravi kumar from HYDERABAD, INDIA > > i have a 2503 router in my office. recently we got ISDN connection from local > basic telephone service provider (DOT) and bought ISDN internet account from > local ISP. I want to provide internet access to all my staff through this > router. > > i configured my router's BRI 0 port with following commands for DDR. > > 1)router# config terminal > > 2) ip route 0.0.0.0 0.0.0.0 bri 0 > and > 3) ip router 0.0.0.0 0.0.0.0 next hop count > > 3) dialer-list 4 protocol ip permit > > 4)interface bri 0 > (i did not assign any ip address to bri port, since ISP server will give ip > address to port once connection is established) > > 5) isdn switch type basic-net3 > > 6) isdn spid1 <7digit number> > > 7) dialer-group 4 > > 8) dialer map ip nexthopaddress numbertodial > (basically ISP will give only phone number to dial. but by using isdn card in > my pc and dialing to ISP, i got dial-up server ip address. i used this address > as gateway address for my router) > > 9) encapsulation ppp > > 10) ppp authentication pap username xyz password abc > > 11) dialer idle-timout 30 > > after this i saved configuration and rebooted the router. > > if i run show ip interface, it is showing bri 0 is up and line protocol is > up. > but if i run show isdn status, it is showing bri 0 layer is deactivated and > layer 1 is not active. > > my queries are > > 1) is this configuration is right or wrong? > > 2) if it is right, how it initiate the call to isp? > > 3) if it is not right, pls let me know step by step cofiguration to dialup > ISP. > > your help in this regard is highly apprecaited. > > regards > ravi kumar B. > > > Get free email and a permanent address at http://www.netaddress.com/?N=1 > > ___ > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html > FAQ, list archives, and subscription info: http://www.groupstudy.com > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
