Re: Re: NSLU2 Debian Installer Erroneous asking for an IP address
A simple workaround for people having problem with this. Wait to plug-in the network cable until the slug finished booting. It will fail to get a dhcp address and will fallback to static ip. Greets On Jan 8, 2008 7:49 PM, Mike (mwester) [EMAIL PROTECTED] wrote: So, basically even though the user has specified a static IP, the unit DHCP's anyway. Considering that a well-behaved DHCP server will probe the active addresses, it's *guaranteed* that not even by accident will the NSLU2 get the static IP that the user set. Hence the device is lost on the ether. Debugging this situation is difficult for the novice. First, the user set a static IP -- there's no reason for them to go check their router to see if it issued a DHCP IP in the first place; they're not expecting that to happen. Secondly, many routers don't even provide a means to check what DHCP has done, so the user can't discover the IP even if a wiki or document told them to do so (I believe that Linksys, one of the most common routers in this area, is one such vendor). Personally, I find this behavior of the installer to be wrong, in the same way that I would be angry if my automobile took it upon itself to turn the steering wheel for me, because I happened to leave the turn-signal activated for too long. But I'm not a Debian user (I just happen to frequent the #nslu2-general IRC channel where this issue has become so commonly asked). IMO, if this behavior is retained, it needs a gigantic red box (flashing, preferably) on the web pages describing the installation process. Many of the users I encounter on that IRC channel are truely novices, so the text also should not just limit itself to outlining the behavior, but the implications of it as well (that the unit will DHCP and that many users may not have routers that offer the ability to see what the DHCP IP might have been, resulting in an NLSU2 on the network that is well and truely lost). And, no, running nmap to find it is not an option for most of these users! Regards, Mike (mwester) -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
fan control on thecus n2100
Hi With kernel 2.6.23 the F75375 driver for the fan control was updated. AFAICS it should now support automatic fan control, but I did not suceeed in enableing it. Is there any documentation for the files in /sys/devices/platform/IOP3xx-I2C.0/i2c-adapter\:i2c-0/0-002e/ How can I set the fan speed manually now and how do I enable automatic fan control (if possible)? Gaudenz -- Ever tried. Ever failed. No matter. Try again. Fail again. Fail better. ~ Samuel Beckett ~ -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Upgrading kernel on a NSLU2
hi I have installed debian on my NSLU2 a while back... (June07 I guess) I am able to happily use apt-get upgrade to upgrade all but the kernel image. I am really worried on using apt-get to upgrade the kernel. Can somebody guide me on how to upgrade the kernel. More specifically the following are my concerns. (I am referring to Installing Debian on the Linksys NSLU2 guide) 1. There is an unofficial debian image at http://www.slug-firmware.net/d-dls.php which has the IXP4xx microcode. I remember installing this on my NSLU2. Currently I have: uname -a: Linux vault 2.6.18-4-ixp4xx #1 Tue Mar 27 18:01:56 BST 2007 armv5tel GNU/Linux dpkg -l | grep linux-image ii linux-image-2.6.18-4-ixp4xx 2.6.18.dfsg.1-12 Linux 2.6.18 image on IXP4xx slug:~# apt-get upgrade Reading package lists... Done Building dependency tree... Done The following packages will be upgraded: linux-image-2.6.18-4-ixp4xx 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 8851kB of archives. After unpacking 0B of additional disk space will be used. Do you want to continue [Y/n]? n Abort. If I do a apt-get upgrade how does the proprietary IXP4xx microcode get included ? 2. I know that linux-image-2.6-ixp4xx (2.6.18+6etch2) is available, but I am really not sure why apt-get is telling me to upgrade to 2.6.18-4 only... The recent kernel deb seems to be released the last Christmas day... linux-image-2.6.18-5-ixp4xx_2.6.18.dfsg.1-17_arm.deb25-Dec-2007 12:47 8.4M It would be nice if there were instructions on how one can upgrade the kernel on the debian-slug install page.. Regards Mayuresh --When there is a Will, There is a way..
Re: fan control on thecus n2100
* Gaudenz Steinlin [EMAIL PROTECTED] [2008-01-09 11:27]: How can I set the fan speed manually now and how do I enable automatic fan control (if possible)? I don't know which tools to use to control it automatically, but here are instructions for manual use: By default, the fan should run at full speed. If you need to regulate the speed, you need to locate the pwm files in /sys: find /sys/ | grep pwm /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm2 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm1 If you want to stop the fan, you have to write the value zero to these files: echo 0 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm2 echo 0 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm1 You can activate full speed using the following commands: echo 255 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm1 echo 255 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm2 -- Martin Michlmayr http://www.cyrius.com/ -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Upgrading kernel on a NSLU2
[EMAIL PROTECTED] wrote: hi I have installed debian on my NSLU2 a while back... (June07 I guess) I am able to happily use apt-get upgrade to upgrade all but the kernel image. I am really worried on using apt-get to upgrade the kernel. Can somebody guide me on how to upgrade the kernel. More specifically the following are my concerns. (I am referring to Installing Debian on the Linksys NSLU2 http://www.cyrius.com/debian/nslu2/install.html guide) 1. There is an unofficial debian image at http://www.slug-firmware.net/d-dls.php which has the IXP4xx microcode. I remember installing this on my NSLU2. Currently I have: uname -a: Linux vault 2.6.18-4-ixp4xx #1 Tue Mar 27 18:01:56 BST 2007 armv5tel GNU/Linux dpkg -l | grep linux-image ii linux-image-2.6.18-4-ixp4xx 2.6.18.dfsg.1-12 Linux 2.6.18 image on IXP4xx slug:~# apt-get upgrade Reading package lists... Done Building dependency tree... Done The following packages will be upgraded: linux-image-2.6.18-4-ixp4xx 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 8851kB of archives. After unpacking 0B of additional disk space will be used. Do you want to continue [Y/n]? n Abort. If I do a apt-get upgrade how does the proprietary IXP4xx microcode get included ? 2. I know that linux-image-2.6-ixp4xx (2.6.18+6etch2) is available, but I am really not sure why apt-get is telling me to upgrade to 2.6.18-4 only... The recent kernel deb seems to be released the last Christmas day... linux-image-2.6.18-5-ixp4xx_2.6.18.dfsg.1-17_arm.deb http://http.us.debian.org/debian/pool/main/l/linux-2.6/linux-image-2.6.18-5-ixp4xx_2.6.18.dfsg.1-17_arm.deb 25-Dec-2007 12:47 8.4M It would be nice if there were instructions on how one can upgrade the kernel on the debian-slug install page.. Regards Mayuresh -- When there is a Will, There is a way.. I'm interested in that too. I will follow this thread. Xan. PS: I install debian in jul. 07
Re: fan control on thecus n2100
On Wed, Jan 09, 2008 at 11:27:22AM +0100, Gaudenz Steinlin wrote: suceeed in enableing it. Is there any documentation for the files in /sys/devices/platform/IOP3xx-I2C.0/i2c-adapter\:i2c-0/0-002e/ see: Documentation/hwmon/sysfs-interface How can I set the fan speed manually now and how do I enable automatic fan control (if possible)? Martin already explained the manual control. Automatic control using just the fintek chip would require reliable reading of fan speed, which does not appear to be the case on N2100. However, such tool can be written for userland (I think someone did already?). -- rm -rf only sounds scary if you don't have backups -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Thecus N2100 - problems after flashing
* Salvatore Iovene [EMAIL PROTECTED] [2008-01-09 09:31]: Hi, and thanks for the answer. After all everything turned out to be fine. It seems that the Thecus leased a DHCP address after all, and I just insisted on probin 192.168.1.100. :) This is documented: If you have used a static configuration different from the default address 192.168.1.100, these values will be used. Otherwise, the installer will ask a DHCP server in your network for an IP configuration. However, if you read other messages posted to debian-arm in the last few days you'll see a discussion about whether the current behaviour is a good idea. -- Martin Michlmayr http://www.cyrius.com/ -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Thecus N2100 - problems after flashing
On Wed, Jan 09, 2008 at 06:10:18PM +0100, Martin Michlmayr wrote: * Salvatore Iovene [EMAIL PROTECTED] [2008-01-09 09:31]: Hi, and thanks for the answer. After all everything turned out to be fine. It seems that the Thecus leased a DHCP address after all, and I just insisted on probin 192.168.1.100. :) This is documented: If you have used a static configuration different from the default address 192.168.1.100, these values will be used. Otherwise, the installer will ask a DHCP server in your network for an IP configuration. However, if you read other messages posted to debian-arm in the last few days you'll see a discussion about whether the current behaviour is a good idea. Indeed it's documented, even tho at first sight I just thought that if I had a static address, that will be used. But it actually is a static address different from 192.168.1.100. I agree that this should be changed to a more intuitive way: if the original fw had a static address, then keep it (whatever be it). If it had dhcp, then do dhcp. At least that's what I expected. I was so sure that I even went to buy a soldering gun and after a night sleep I figured that maybe it used dhcp so I went to check the leases on the dhcp server. -- Salvatore Iovene http://www.iovene.com/ signature.asc Description: Digital signature
Re: Upgrading kernel on a NSLU2
* [EMAIL PROTECTED] [EMAIL PROTECTED] [2008-01-09 06:37]: If I do a apt-get upgrade how does the proprietary IXP4xx microcode get included ? The IXP4xx microcode is stored in /lib/firmware and will still be there when you upgrade the kernel. 2. I know that linux-image-2.6-ixp4xx (2.6.18+6etch2) is available, but I am really not sure why apt-get is telling me to upgrade to 2.6.18-4 only... It should install 2.6.18-5. Does apt-get dist-upgrade rather than apt-get upgrade help? Did you run apt-get update first? -- Martin Michlmayr http://www.cyrius.com/ -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Upgrading kernel on a NSLU2
[EMAIL PROTECTED] wrote: I am really worried on using apt-get to upgrade the kernel. Can somebody guide me on how to upgrade the kernel. More specifically the following are my concerns. (I am referring to Installing Debian on the Linksys NSLU2 http://www.cyrius.com/debian/nslu2/install.html guide) 1. There is an unofficial debian image at http://www.slug-firmware.net/d-dls.php which has the IXP4xx microcode. I remember installing this on my NSLU2. I installed my NSLU2 exactly the same way in September 2007 (I think). As long as I stick to debian etch in sources.list, aptitude upgrade works just fine. The microcode is saved somewhere on the hard drive, and when the kernel is upgraded, the slug automatically builds a new flash image including the kernel, drivers and I think the boot system and then writes it to the the internal memory. This takes some time, so it's better to run that in a screen session. I'd recommend to backup your image though, using cat /dev/mtdblock* image-backup.bin and copying the result to your computer. If anything goes wrong, you can just write that image back using upslug2 or the Sercom tool. Greets, Lee (taking no responsibility for the results - but it works for me). -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: fan control on thecus n2100
Martin Michlmayr wrote: * Gaudenz Steinlin [EMAIL PROTECTED] [2008-01-09 11:27]: How can I set the fan speed manually now and how do I enable automatic fan control (if possible)? I don't know which tools to use to control it automatically, but here are instructions for manual use: By default, the fan should run at full speed. If you need to regulate the speed, you need to locate the pwm files in /sys: find /sys/ | grep pwm /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm2 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm1 If you want to stop the fan, you have to write the value zero to these files: echo 0 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm2 echo 0 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm1 You can activate full speed using the following commands: echo 255 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm1 echo 255 /sys/devices/platform/IOP3xx-I2C.0/i2c-0/0-002e/pwm2 See http://www.debonaras.org/wiki/Info/N2100FanControl for a shell script that regulates the fan by reading system and disk temperatures. Fan control has only a very small control range, and the script needs to be tuned for that, but when that is done it works just fine. Frank -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: armel packages for linux-2.6.23-2 and install problem
Figured it out finally. When you use RedBoot to create images loaded over the net, as well as the partition length, it sets the load size for the partitions as well, which do not (and cannot) get updated when new contents are written in from linux. Specifically, RedBoot load -v -r -b 0x80 -m http -h 192.168.1.1 /.../initrd.img-2.6.23-1-iop32x RedBoot fis create -l 0xd0 -s 0xd0 ramdisk So the new, bigger initrd was only getting loaded into RAM as far as the length of the old one. For default installations where no half-witted redbooting has been going on, the new kernels should work fine. Enjoy M -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Packages that only match linux-gnu in configure
Hi, As pointed out by Lennert, there is a huge amount of configure scripts looking at *-*-linux-gnu) in kde packages. Fortunately, looking more closely, these appear mostly harmless - Ie they are only used to turn on some warnings. In other cases, these can cause failures to build, missing functionality of applications or needless lack of optimizations. This triggered me to grep the source archive for cases where the configure scripts look for -linux-gnu) instead of -linux-gnu*).a The list follows (cleaned up from kde packages and obvious false positives). I've failed two bugs so far (alpine: #459830, gamin: #459936). ./alpine-1.0+dfsg/configure:*-linux-gnu) ./alpine-1.0+dfsg/configure: *-linux-gnu) ./alpine-1.0+dfsg/configure.ac:*-linux-gnu) ./alpine-1.0+dfsg/configure.ac: *-linux-gnu) ./am-utils-6.1.5/configure.in: # Temporarily undo renaming of linux-gnu to linux, because ./am-utils-6.1.5/configure.in: # libtool only looks for linux-gnu. Sigh. ./am-utils-6.1.5/configure.in: linux ) host_os=linux-gnu ;; ./am-utils-6.1.5/configure.in: # end temporary renaming of linux-gnu to linux ./am-utils-6.1.5/configure.in: linux-gnu ) host_os=linux ;; ./am-utils-6.1.5/configure: # Temporarily undo renaming of linux-gnu to linux, because ./am-utils-6.1.5/configure: # libtool only looks for linux-gnu. Sigh. ./am-utils-6.1.5/configure: linux ) host_os=linux-gnu ;; ./am-utils-6.1.5/configure: # end temporary renaming of linux-gnu to linux ./am-utils-6.1.5/configure: linux-gnu ) host_os=linux ;; ./arson-0.9.8beta2/configure: *-*-linux-gnu) ./asterisk-1.4.17~dfsg/configure:if test ${host_os} != linux-gnu ; then ./asterisk-1.4.17~dfsg/configure.ac:if test ${host_os} != linux-gnu ; then ./boa-0.94.14rc21/configure.in:dnl AC_MSG_RESULT($host) dnl i686-pc-linux-gnu ./boa-0.94.14rc21/configure.in:dnl AC_MSG_RESULT($host_os) dnl linux-gnu ./bzflag-2.0.10.20071115/configure:if test x$host_os = xlinux-gnu -o x$host_os = xlinux ; then ./bzflag-2.0.10.20071115/configure.ac:if test x$host_os = xlinux-gnu -o x$host_os = xlinux ; then ./c-cpp-reference-2.0.2/configure:*-*-linux-gnu) ./c-cpp-reference-2.0.2/configure: case $host in*-*-linux-gnu) ./cdebootstrap-0.4.3/configure: if test $target_os = linux-gnu; then ./cdebootstrap-0.4.3/configure.ac: if test $target_os = linux-gnu; then ./cdparanoia-3.10+debian~pre0/configure.sub:os=`echo $os | sed -e 's|gnu/linux|linux-gnu|'` ./cdparanoia-3.10+debian~pre0/configure.sub:os=`echo $os | sed -e 's|linux|linux-gnu|'` ./cdparanoia-3.10+debian~pre0/configure.guess: # suitable tag, in the style of linux-gnu. ./cdparanoia-3.10+debian~pre0/configure.guess: echo ${UNAME_MACHINE}-unknown-linux-gnu ./cdparanoia-3.10+debian~pre0/configure.guess: echo x86_64-unknown-linux-gnu ./cdparanoia-3.10+debian~pre0/configure.guess: echo xtensa-unknown-linux-gnu ./cdparanoia-3.10+debian~pre0/configure.guess: TENTATIVE=${UNAME_MACHINE}-pc-linux-gnu ./cdparanoia-3.10+debian~pre0/configure.guess: echo ${UNAME_MACHINE}-pc-linux-gnuaout ./cdparanoia-3.10+debian~pre0/configure.guess: echo ${UNAME_MACHINE}-pc-linux-gnucoff ./classpath-0.96.1/configure: target_os=linux-gnu/classpath-0.96.1/configure.ac:target_os=linux-gnu ./classpath-0.96.1/configure.ac:AC_MSG_WARN(no, using x86-linux-gnu) ./creox-0.2.2rc2/configure: *-*-linux-gnu) ./dbus-1.1.2/configure.in:if test x$target_os = xlinux-gnu -o x$target_os = xlinux; then ./dbus-1.1.2/configure:if test x$target_os = xlinux-gnu -o x$target_os = xlinux; then ./droidbattles-1.0.6/configure: *-*-linux-gnu) ./facturalux-0.4/configure: *-*-linux-gnu) ./fenix-0.92a.dfsg1/configure.in:linux-gnu) ./fenix-0.92a.dfsg1/configure:linux-gnu) ./flac-1.2.1/configure.in: *-pc-linux-gnu) ./flac-1.2.1/configure: *-pc-linux-gnu) ./fraqtive-0.3.1/configure: *-*-linux-gnu) ./fraqtive-0.3.1/configure: *-*-linux-gnu) linux-gnutlsto compile on a linux host and install in /usr/local linux-gnutls) ./freesweep-0.88/configure.in: if test $host_os = 'linux' || test $host_os = 'linux-gnu' || test $host_os = ' gnu0.2'; then ./freesweep-0.88/configure: if test $host_os = 'linux' || test $host_os = 'linux-gnu' || tes t $host_os = 'gnu0.2'; then ./ftdi-eeprom-0.2/configure:*-*-linux-gnu) ./gamin-0.1.9/configure.in:#AM_CONDITIONAL(HAVE_LINUX, test x$target_os = xlinux-gnu) ./gamin-0.1.9/configure.in:if test x$target_os = xlinux-gnu; then ./gamin-0.1.9/configure.in:if test x$os = xlinux-gnu; then ./gamin-0.1.9/configure.in:if test x$os = xlinux-gnu; then ./gamin-0.1.9/configure.in:if test x$os = xlinux-gnu -a x$WITH_THREADS = x1 ; then ./gamin-0.1.9/configure:#AM_CONDITIONAL(HAVE_LINUX, test x$target_os = xlinux-gnu) ./gamin-0.1.9/configure:if test x$target_os = xlinux-gnu; then
Re: Upgrading kernel on a NSLU2
HI Martin, Thanks for the confirmation, the upgrade did work but with some tiny effort... see the log below I had to install the specific version by using linux-image =version_number... == myslug:~/kernel# apt-get clean myslug:~/kernel# apt-get clean all myslug:~/kernel# apt-get update Get:1 http://natasha.stmarytx.edu etch Release.gpg [378B] Hit http://natasha.stmarytx.edu etch Release Get:2 http://security.debian.org etch/updates Release.gpg [189B] Get:3 http://www.backports.org etch-backports Release.gpg [189B] Get:4 http://security.debian.org etch/updates Release [22.5kB] Get:5 http://www.backports.org etch-backports Release [43.7kB] Ign http://natasha.stmarytx.edu etch/main Packages/DiffIndex Ign http://natasha.stmarytx.edu etch/main Sources/DiffIndex Hit http://natasha.stmarytx.edu etch/main Packages Hit http://natasha.stmarytx.edu etch/main Sources Ign http://security.debian.org etch/updates/main Packages/DiffIndex Ign http://security.debian.org etch/updates/main Sources/DiffIndex Get:6 http://security.debian.org etch/updates/main Packages [191kB] Hit http://www.backports.org etch-backports/main Packages/DiffIndex Hit http://www.backports.org etch-backports/contrib Packages/DiffIndex Hit http://www.backports.org etch-backports/non-free Packages/DiffIndex Get:7 http://www.backports.org etch-backports/contrib 2007-06-10-0940.10.pdiff [596B] Get:8 http://www.backports.org etch-backports/contrib 2007-06-10-0940.10.pdiff [596B] Get:9 http://www.backports.org etch-backports/contrib 2007-06-10-0940.10.pdiff [596B] Ign http://www.backports.org etch-backports/contrib 2007-06-10-0940.10.pdiff Get:10 http://security.debian.org etch/updates/main Sources [28.9kB] Hit http://www.backports.org etch-backports/contrib Fetched 287kB in 6s (45.6kB/s) Reading package lists... Done myslug:~/kernel# apt-get dist-upgrade Reading package lists... Done Building dependency tree... Done Calculating upgrade... Done The following packages will be upgraded: linux-image-2.6.18-4-ixp4xx 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 8851kB of archives. After unpacking 0B of additional disk space will be used. Do you want to continue [Y/n]? n Abort. myslug:~/kernel# man apt-get Reformatting apt-get(8), please wait... myslug:~/kernel# apt-get -f apt 0.6.46.4-0.1 for linux arm compiled on Feb 26 2007 22:44:23 Usage: apt-get [options] command apt-get [options] install|remove pkg1 [pkg2 ...] apt-get [options] source pkg1 [pkg2 ...] apt-get is a simple command line interface for downloading and installing packages. The most frequently used commands are update and install. Commands: update - Retrieve new lists of packages upgrade - Perform an upgrade install - Install new packages (pkg is libc6 not libc6.deb) remove - Remove packages source - Download source archives build-dep - Configure build-dependencies for source packages dist-upgrade - Distribution upgrade, see apt-get(8) dselect-upgrade - Follow dselect selections clean - Erase downloaded archive files autoclean - Erase old downloaded archive files check - Verify that there are no broken dependencies Options: -h This help text. -q Loggable output - no progress indicator -qq No output except for errors -d Download only - do NOT install or unpack archives -s No-act. Perform ordering simulation -y Assume Yes to all queries and do not prompt -f Attempt to continue if the integrity check fails -m Attempt to continue if archives are unlocatable -u Show a list of upgraded packages as well -b Build the source package after fetching it -V Show verbose version numbers -c=? Read this configuration file -o=? Set an arbitrary configuration option, eg -o dir::cache=/tmp See the apt-get(8), sources.list(5) and apt.conf(5) manual pages for more information and options. This APT has Super Cow Powers. myslug:~/kernel# apt-get -d dist-upgrade Reading package lists... Done Building dependency tree... Done Calculating upgrade... Done The following packages will be upgraded: linux-image-2.6.18-4-ixp4xx 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 8851kB of archives. After unpacking 0B of additional disk space will be used. Do you want to continue [Y/n]? y Get:1 http://security.debian.org etch/updates/main linux-image-2.6.18-4-ixp4xx 2.6.18.dfsg.1-12etch2 [8851kB] Fetched 8851kB in 24s (364kB/s) Download complete and in download only mode myslug:~/kernel# dpkg -l | grep linux ii foomatic-db 20061031-1 linuxprinting.org printer support - database ii foomatic-db-engine 3.0.2-20061031-1 linuxprinting.org printer support - programs ii foomatic-filters 3.0.2-20061031-1.2 linuxprinting.org printer support - filters ii libselinux1
building ipcld on debian/NSLU
hi I am trying to build the iplcd driver for the NSLU2 http://www.linuxha.com/athome/common/iplcd/iplc-driver.tgz This is for the USB Insteon PowerLinc V2 I am looking for the kernel build library which is not installed with the linux-image package... myslug:~/smarthome/iplc/driver/linux-2.6# make make -C /lib/modules/2.6.18-5-ixp4xx/build/ SUBDIRS=/home/super1/smarthome/iplc/driver/linux-2.6 modules make: *** /lib/modules/2.6.18-5-ixp4xx/build/: No such file or directory. Stop. make: *** [default] Error 2 What package do I need to install to get the build directory for the kernel ? Mayuresh --When there is a Will, There is a way..