Bug#412029: effect is not as bad on powerpc

2007-02-22 Thread alve
With the same version of openoffice on powerpc instead of x86 the effect 
is much better, but still visible.



--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]



Bug#402639: at76c503a-source: connecting to hidden ESSIDs broken

2006-12-11 Thread alve
Package: at76c503a-source
Version: 0.14~beta1-3
Severity: normal

I'm retrying to send this report with a different email adress since I didn't 
get an acknowledgement 
yesterday - sorry, if the other report does show up again. In the mean time I 
have done some more 
tests and found out that "only" the connecting to the hidden ESSID is broken. 
If the debian system 
with the Netgear Wifi is running and I configure the AP to show the ESSID from 
another computer, the 
debian station instantly connects. Also in this case the signal strength shows 
different results. It 
doesn't disappear like before but jumps between 20-30/100 and 2/100. The link 
is good again.

So, this is the original report:

I can't connect to my AP any more since I upgraded the driver from 
0.13.0+2.6.17-8_amd64. I also tried 
with kernel 2.6.18-3-amd64 with the same results. My AP hides its ESSID and 
uses 128 bit WEP. With the 
older driver "iwlist wlan0 scan" gives the following output, when connected to 
my AP, "Wurstmann":

wlan0 Scan completed :
  Cell 01 - Address: 00:03:C9:A3:04:3E
ESSID:"Wurstmann"
Mode:Master
Channel:1
Encryption key:on
Quality:0/0  Signal level:10/255  Noise level:0/0
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
  24 Mb/s; 36 Mb/s; 54 Mb/s
  Cell 02 - Address: 00:14:6C:A1:77:CA
ESSID:"wild warthe"
Mode:Master
Channel:11
Encryption key:on
Quality:0/0  Signal level:1/255  Noise level:0/0
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
  24 Mb/s; 36 Mb/s; 54 Mb/s


"wild warthe" is not always visible though, due to low signal. With the new 
driver "wild warthe" is 
always visible at signal level 2/100 and "Wurstmann" is only rarely visible, 
but when it's there it 
has about 30/100 signal level. Although the signal level seems low with the old 
driver I never 
experienced any problems with the link. My AP is about 7 Meters away with a 
wall and an open door 
between AP and station. I have a Netgear MA101 and it has a slightly damaged 
antenna. lsusb gives this:

Bus 005 Device 002: ID 07cc:0320 Carry Computer Eng., Co., Ltd 
Bus 005 Device 001: ID :  
Bus 001 Device 001: ID :  
Bus 004 Device 007: ID 0864:4102 NetGear, Inc. MA101 802.11b Adapter
Bus 004 Device 004: ID 046d:c505 Logitech, Inc. Cordless Mouse+Keyboard Receiver
Bus 004 Device 001: ID :  
Bus 003 Device 001: ID :  
Bus 002 Device 001: ID :  


-- System Information:
Debian Release: 4.0
  APT prefers testing
  APT policy: (990, 'testing')
Architecture: amd64 (x86_64)
Shell:  /bin/sh linked to /bin/bash
Kernel: Linux 2.6.17-2-amd64
Locale: [EMAIL PROTECTED], [EMAIL PROTECTED] (charmap=ISO-8859-15)

Versions of packages at76c503a-source depends on:
ii  atmel-firmware1.3-2  Firmware for Atmel at76c50x wirele
ii  debhelper 5.0.42 helper programs for debian/rules

at76c503a-source recommends no packages.

-- no debconf information




-- 
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]



Bug#338426: possibly memory-bandwidth issue

2005-12-15 Thread alve
I got the same problem - flashing horizontal lines when using keyboard 
and only with gnome. Also I have a low-end graphics chip (sis 740 using 
exclusively system ram) which is known to produce the same problem when 
using it in double headed mode and exceeding the available memory 
bandwidth like that.
So there might be something in gnome that issues some bandwidth-hungry 
action each time you press a key. Just my 2c



--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]



Bug#333508: really nothing no suspeicious messages in the logs

2005-10-16 Thread alve

Just to make things clearer:

"grep -nE -H pbbuttonsd /var/log/*" doesn't give any suspicious messages 
only piles of "INFO" about which scripts have been started and such. Of 
course when I installed a new kernel and forgot to load evdev I got a 
WARNING about that but after "echo evdev >> /etc/modules" everything was 
the same again ...


I really have no idea what is going on there.

Ulf


--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]