Re: [Newbie] ppp: Connection established, but can't ping. How can I get out into Internet?
Scotty Fitzgerald wrote: > I had a similar problem, When I set up the machine I > had a Ethernet card that was autodetected, and the > the autodetection set up the ethernet card as the default > gateway to the internet. While your ethernet is the default > gateway the dialup won't establish itself as a gateway. Try to > remove the gateway status of your ethernet card, and things should work. > > It took me a few googles on Linux networking and I found this, but if > you can't find a good webpage post a reply, and I will actually start up > my old windows partition and see if I can find the webpage that clued me > in. > > Good luck, > --- > Scotty > > F. GEIGER wrote: > >> Dear all, >> >> I'm on Debian GNU/Linux 3.0 (Woody) and stuck in the middle: >> >> I exec "pon VOL" and get a connection, but no pings do return (100% >> loss). >> >> As a connection has been estblished, I guess the several config files are >> okay. Therefore I've pasted the output of "netstat -nr", "route", and >> "ifconf ppp0", shown while the connection is established. >> >> As I come from an OS, where one can configure an Internet connection with >> a few clicks and get into the Internet with two more clicks (did I >> already say, I'm a newbie? :-)), it's beyond me to fully recognize all >> the content of those lines. My Linux box' address is 192.168.200.101. >> This leads me to find the lines >> >> 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 >> sl0 >> >> and >> >> default * 0.0.0.0 U 1 00 >> sl0 >> >> kind of strange. But, please, see for yourselves: >> >> netstat -nr >> Kernel IP routing table >> Destination Gateway Genmask Flags MSS Window irtt >> Iface >> 194.183.133.58 0.0.0.0 255.255.255.255 UH0 0 0 >> ppp0 >> 192.168.0.2 0.0.0.0 255.255.255.255 UH0 0 0 >> sl0 >> 192.168.200.0 0.0.0.0 255.255.255.0 U 0 0 0 >> eth0 >> 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 >> sl0 >> >> >> route >> Kernel IP routing table >> Destination Gateway Genmask Flags Metric RefUse >> Iface >> 194.183.133.58 * 255.255.255.255 UH0 00 >> ppp0 >> 192.168.0.2 * 255.255.255.255 UH1 00 >> sl0 >> 192.168.200.0 * 255.255.255.0 U 0 00 >> eth0 >> default * 0.0.0.0 U 1 00 >> sl0 >> >> >> ifconfig ppp0 >> ppp0 Link encap:Point-to-Point Protocol >> inet addr:194.208.126.37 P-t-P:194.183.133.58 >> Mask:255.255.255.255 >> UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 >> RX packets:14 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:10 >> RX bytes:425 (425.0 b) TX bytes:355 (355.0 b) >> >> So, what am I missing? Do I have to add or change a default route or >> something like that? >> >> Kind regards >> Franz GEIGER, lookin' for kind helping hands. >> >> > > The line I deleted was "gateway" from the file "/etc/network/interfaces" --- Scotty -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
Re: [Newbie] ppp: Connection established, but can't ping. How can I get out into Internet?
David Clymer wrote: > On Sun, 2004-10-17 at 21:50, Scotty Fitzgerald wrote: >> I had a similar problem, When I set up the machine I >> had a Ethernet card that was autodetected, and the >> the autodetection set up the ethernet card as the default >> gateway to the internet. While your ethernet is the default >> gateway the dialup won't establish itself as a gateway. Try to >> remove the gateway status of your ethernet card, and things should work. >> >> It took me a few googles on Linux networking and I found this, but if >> you can't find a good webpage post a reply, and I will actually start up >> my old windows partition and see if I can find the webpage that clued me >> in. >> > > Please don't top post: http://www.xs4all.nl/~sbpoley/toppost.htm > > A google "i'm feeling lucky" search got me the following page. perhaps > it was the one you were refering to? > > http://www.ale.org/archive/ale/ale-1996-02/msg00026.html > > You could use ip-up & ip-down scripts to setup/tear down routes for your > ppp connection. That would certainly beat doing it manually every time. > > -davidc > > Gee, I always preferred topposts, but ok, Hi, David, I guess I will have to boot up windows tonight (sigh) to get that URL. No, what I had to do was find this configuration file in the /etc hierarchy and delete the line that said "gateway (192.x.x.x" [whatever x was.] After that my dialup took off. cheers! --- Scotty -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
Re: [Newbie] ppp: Connection established, but can't ping. How can I get out into Internet?
On Sun, 2004-10-17 at 21:50, Scotty Fitzgerald wrote: > I had a similar problem, When I set up the machine I > had a Ethernet card that was autodetected, and the > the autodetection set up the ethernet card as the default > gateway to the internet. While your ethernet is the default > gateway the dialup won't establish itself as a gateway. Try to > remove the gateway status of your ethernet card, and things should work. > > It took me a few googles on Linux networking and I found this, but if > you can't find a good webpage post a reply, and I will actually start up my > old windows partition and see if I can find the webpage that clued me in. > Please don't top post: http://www.xs4all.nl/~sbpoley/toppost.htm A google "i'm feeling lucky" search got me the following page. perhaps it was the one you were refering to? http://www.ale.org/archive/ale/ale-1996-02/msg00026.html You could use ip-up & ip-down scripts to setup/tear down routes for your ppp connection. That would certainly beat doing it manually every time. -davidc -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
Re: [Newbie] ppp: Connection established, but can't ping. How can I get out into Internet?
I had a similar problem, When I set up the machine I had a Ethernet card that was autodetected, and the the autodetection set up the ethernet card as the default gateway to the internet. While your ethernet is the default gateway the dialup won't establish itself as a gateway. Try to remove the gateway status of your ethernet card, and things should work. It took me a few googles on Linux networking and I found this, but if you can't find a good webpage post a reply, and I will actually start up my old windows partition and see if I can find the webpage that clued me in. Good luck, --- Scotty F. GEIGER wrote: > Dear all, > > I'm on Debian GNU/Linux 3.0 (Woody) and stuck in the middle: > > I exec "pon VOL" and get a connection, but no pings do return (100% loss). > > As a connection has been estblished, I guess the several config files are > okay. Therefore I've pasted the output of "netstat -nr", "route", and > "ifconf ppp0", shown while the connection is established. > > As I come from an OS, where one can configure an Internet connection with > a few clicks and get into the Internet with two more clicks (did I already > say, I'm a newbie? :-)), it's beyond me to fully recognize all the content > of those lines. My Linux box' address is 192.168.200.101. This leads me to > find the lines > > 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 > sl0 > > and > > default * 0.0.0.0 U 1 00 > sl0 > > kind of strange. But, please, see for yourselves: > > netstat -nr > Kernel IP routing table > Destination Gateway Genmask Flags MSS Window irtt > Iface > 194.183.133.58 0.0.0.0 255.255.255.255 UH0 0 0 > ppp0 > 192.168.0.2 0.0.0.0 255.255.255.255 UH0 0 0 > sl0 > 192.168.200.0 0.0.0.0 255.255.255.0 U 0 0 0 > eth0 > 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 > sl0 > > > route > Kernel IP routing table > Destination Gateway Genmask Flags Metric RefUse > Iface > 194.183.133.58 * 255.255.255.255 UH0 00 > ppp0 > 192.168.0.2 * 255.255.255.255 UH1 00 > sl0 > 192.168.200.0 * 255.255.255.0 U 0 00 > eth0 > default * 0.0.0.0 U 1 00 > sl0 > > > ifconfig ppp0 > ppp0 Link encap:Point-to-Point Protocol > inet addr:194.208.126.37 P-t-P:194.183.133.58 > Mask:255.255.255.255 > UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 > RX packets:14 errors:0 dropped:0 overruns:0 frame:0 > TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:10 > RX bytes:425 (425.0 b) TX bytes:355 (355.0 b) > > So, what am I missing? Do I have to add or change a default route or > something like that? > > Kind regards > Franz GEIGER, lookin' for kind helping hands. > > -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
[Newbie] ppp: Connection established, but can't ping. How can I get out into Internet?
Dear all, I'm on Debian GNU/Linux 3.0 (Woody) and stuck in the middle: I exec "pon VOL" and get a connection, but no pings do return (100% loss). As a connection has been estblished, I guess the several config files are okay. Therefore I've pasted the output of "netstat -nr", "route", and "ifconf ppp0", shown while the connection is established. As I come from an OS, where one can configure an Internet connection with a few clicks and get into the Internet with two more clicks (did I already say, I'm a newbie? :-)), it's beyond me to fully recognize all the content of those lines. My Linux box' address is 192.168.200.101. This leads me to find the lines 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 sl0 and default * 0.0.0.0 U 1 00 sl0 kind of strange. But, please, see for yourselves: netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 194.183.133.58 0.0.0.0 255.255.255.255 UH0 0 0 ppp0 192.168.0.2 0.0.0.0 255.255.255.255 UH0 0 0 sl0 192.168.200.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 sl0 route Kernel IP routing table Destination Gateway Genmask Flags Metric RefUse Iface 194.183.133.58 * 255.255.255.255 UH0 00 ppp0 192.168.0.2 * 255.255.255.255 UH1 00 sl0 192.168.200.0 * 255.255.255.0 U 0 00 eth0 default * 0.0.0.0 U 1 00 sl0 ifconfig ppp0 ppp0 Link encap:Point-to-Point Protocol inet addr:194.208.126.37 P-t-P:194.183.133.58 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:425 (425.0 b) TX bytes:355 (355.0 b) So, what am I missing? Do I have to add or change a default route or something like that? Kind regards Franz GEIGER, lookin' for kind helping hands. -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]