[dpdk-dev] [PATCH] i40e: skip any phy config as a workaround

[Zhang, Helin]

> -Original Message-
> From: Thomas Monjalon [mailto:thomas.monjalon at 6wind.com]
> Sent: Tuesday, November 24, 2015 6:17 AM
> To: Zhang, Helin
> Cc: dev at dpdk.org
> Subject: Re: [dpdk-dev] [PATCH] i40e: skip any phy config as a workaround
> 
> 2015-11-17 15:09, Helin Zhang:
> > As firmware does not support any link control from software driver
> > side, any phy config should be ignored as a workaround. Otherwise the
> > link might not be up again after binding back to kernel driver.
> >
> > Signed-off-by: Helin Zhang 
> [...]
> > +i40e_phy_conf_link(__rte_unused struct i40e_hw *hw,
> > +  __rte_unused uint8_t abilities,
> > +  __rte_unused uint8_t force_speed) {
> > +   /* Skip any phy config on both 10G and 40G interfaces, as a
> workaround
> > +* for the link control limitation of that all link control should be
> > +* handled by firmware. It should follow up if link control will be
> > +* opened to software driver in future firmware versions.
> > +*/
> > return I40E_SUCCESS;
> >  }
> 
> An error code seems more appropriate.
> But I guess you perfectly know what you do, so Applied, thanks

Yes, for now, I'd prefer to use I40E_SUCCESS. We will continue working on this 
when
firmware provides the link control to sw driver. Thank you very much!

Regards,
Helin

[dpdk-dev] [PATCH] i40e: skip any phy config as a workaround

[Thomas Monjalon]

2015-11-17 15:09, Helin Zhang:
> As firmware does not support any link control from software driver
> side, any phy config should be ignored as a workaround. Otherwise
> the link might not be up again after binding back to kernel driver.
> 
> Signed-off-by: Helin Zhang 
[...]
> +i40e_phy_conf_link(__rte_unused struct i40e_hw *hw,
> +__rte_unused uint8_t abilities,
> +__rte_unused uint8_t force_speed)
> +{
> + /* Skip any phy config on both 10G and 40G interfaces, as a workaround
> +  * for the link control limitation of that all link control should be
> +  * handled by firmware. It should follow up if link control will be
> +  * opened to software driver in future firmware versions.
> +  */
>   return I40E_SUCCESS;
>  }

An error code seems more appropriate.
But I guess you perfectly know what you do, so
Applied, thanks

[dpdk-dev] [PATCH] i40e: skip any phy config as a workaround

[Helin Zhang]

As firmware does not support any link control from software driver
side, any phy config should be ignored as a workaround. Otherwise
the link might not be up again after binding back to kernel driver.

Signed-off-by: Helin Zhang 
---
 drivers/net/i40e/i40e_ethdev.c | 61 +++---
 1 file changed, 9 insertions(+), 52 deletions(-)

diff --git a/drivers/net/i40e/i40e_ethdev.c b/drivers/net/i40e/i40e_ethdev.c
index 2c51a0b..f06c566 100644
--- a/drivers/net/i40e/i40e_ethdev.c
+++ b/drivers/net/i40e/i40e_ethdev.c
@@ -1347,58 +1347,15 @@ i40e_parse_link_speed(uint16_t eth_link_speed)
 }

 static int
-i40e_phy_conf_link(struct i40e_hw *hw, uint8_t abilities, uint8_t force_speed)
-{
-   enum i40e_status_code status;
-   struct i40e_aq_get_phy_abilities_resp phy_ab;
-   struct i40e_aq_set_phy_config phy_conf;
-   const uint8_t mask = I40E_AQ_PHY_FLAG_PAUSE_TX |
-   I40E_AQ_PHY_FLAG_PAUSE_RX |
-   I40E_AQ_PHY_FLAG_LOW_POWER;
-   const uint8_t advt = I40E_LINK_SPEED_40GB |
-   I40E_LINK_SPEED_10GB |
-   I40E_LINK_SPEED_1GB |
-   I40E_LINK_SPEED_100MB;
-   int ret = -ENOTSUP;
-
-   /* Skip it on 40G interfaces, as a workaround for the link issue */
-   if (i40e_is_40G_device(hw->device_id))
-   return I40E_SUCCESS;
-
-   status = i40e_aq_get_phy_capabilities(hw, false, false, _ab,
- NULL);
-   if (status)
-   return ret;
-
-   memset(_conf, 0, sizeof(phy_conf));
-
-   /* bits 0-2 use the values from get_phy_abilities_resp */
-   abilities &= ~mask;
-   abilities |= phy_ab.abilities & mask;
-
-   /* update ablities and speed */
-   if (abilities & I40E_AQ_PHY_AN_ENABLED)
-   phy_conf.link_speed = advt;
-   else
-   phy_conf.link_speed = force_speed;
-
-   phy_conf.abilities = abilities;
-
-   /* use get_phy_abilities_resp value for the rest */
-   phy_conf.phy_type = phy_ab.phy_type;
-   phy_conf.eee_capability = phy_ab.eee_capability;
-   phy_conf.eeer = phy_ab.eeer_val;
-   phy_conf.low_power_ctrl = phy_ab.d3_lpan;
-
-   PMD_DRV_LOG(DEBUG, "\tCurrent: abilities %x, link_speed %x",
-   phy_ab.abilities, phy_ab.link_speed);
-   PMD_DRV_LOG(DEBUG, "\tConfig:  abilities %x, link_speed %x",
-   phy_conf.abilities, phy_conf.link_speed);
-
-   status = i40e_aq_set_phy_config(hw, _conf, NULL);
-   if (status)
-   return ret;
-
+i40e_phy_conf_link(__rte_unused struct i40e_hw *hw,
+  __rte_unused uint8_t abilities,
+  __rte_unused uint8_t force_speed)
+{
+   /* Skip any phy config on both 10G and 40G interfaces, as a workaround
+* for the link control limitation of that all link control should be
+* handled by firmware. It should follow up if link control will be
+* opened to software driver in future firmware versions.
+*/
return I40E_SUCCESS;
 }

-- 
1.9.3