Re: [Discuss-gnuradio] Help getting started on gnuradio software
On Fri, May 25, 2007 at 10:49:22PM -1000, Angela Kahealani wrote: > Does anyone have good pointers for info about > GnuRadio running on the MC PCI-DAS4020-12? > I know it was supported before the USRP came along. Hi Angela, As far as I know, nobody's used that code in quite a while. There is an mc4020 driver that works for 2.4, and more-or-less works for 2.6 (but doesn't properly create dev files). driver: ftp://ftp.gnu.org/pub/gnu/gnuradio/mc4020-0.9.tar.gz old GNU Radio glue code, needs work to fit in with new build system: ftp://ftp.gnu.org/pub/gnu/gnuradio/gr-mc4020-0.5.tar.gz It may make more sense to check out the comedi driver (http://www.comedi.org/hardware.html). I believe it's being actively supported. We do have a gr-comedi package, but I don't think it's gotten any real testing. It may be a good starting point. FWIW, folks prefer the USRP to the DAS4020-12 since it's does a whole lot more (including the RF to IF conversion) and costs less. Of course, if you've already got a 4020... Eric ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
[Discuss-gnuradio] Help getting started on gnuradio software
Does anyone have good pointers for info about GnuRadio running on the MC PCI-DAS4020-12? I know it was supported before the USRP came along. -- All rights reserve without prejudice, & Copyright 2007 Angela Kahealani. All information and transactions are private between the parties and are non negotiable. http://www.kahealani.com/ ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
Re: [Discuss-gnuradio] Help getting started
Well, all I can think of is using the basic rx daugtherboard along with usrp_wfm_rcv.py and tuning to some local FM stations, or using the scope, but it sounds like you've already done that pretty much. Make sure the gain on the scope is set to about mid-point for the specific daughterboard being used. I had the best luck with this. Depending on your scanning bandwidth, I don't know if you'll actually pick up any listenable stations, so I'd just use the aforementioned file for FM testing purposes. Written Dan Halperin wrote: > > I've used the 2.4GHz RX/TX board, but I have since been using the Basic > RX and Basic TX boards. > > -Dan > > Written wrote: >> Hi Dan, >> >> What daughterboards are you using? >> >> Thanks, >> >> Written >> >> >> Dan Halperin wrote: >> >>> Hi all, >>> >>> I'm just beginning grad school and trying to get my USRP board up and >>> running so I can start playing. I've tested our equipment on two >>> different machines now; one an older box running FC4, 512MB ram, with an >>> Intel(R) Celeron(R) CPU 2.40GHz. I've also tried one on a newer laptop >>> (compaq v3000 series) running Gentoo Linux, with 2GB of memory. I've had >>> /all kinds/ of interesting phenomena: >>> >>> I first tried installing the way on the old wiki >>> http://www.comsec.com/wiki?UniversalSoftwareRadioPeripheral (first link >>> on Google for USRP), and then again using the new say (svn source >>> checkout using the instructions on the new wiki), on both machines. On >>> the older machine, I don't get any rx/tx over/underruns (or maybe just >>> one when initializing) and a throughput of 32MB/s in both directions, >>> and on the laptop I get exactly 41 under/over runs with a throughput of >>> ~31MB/s in the RX direction and around 24 in the TX direction. As far as >>> I could tell, these used the same version of the source, but then again >>> the SVN repository has jumped from rev. 3772 to rev. 3785 since >>> yesterday morning. >>> >>> Anyway, installation, make check, and the ./test_standard_?x scripts >>> work fine (the LED behaves as expected and the benchmarks seem >>> reasonable), however I get nothing when running the usrp_oscope or >>> usrp_wfm_rcv scripts as directed in the instructions. Both dial tone >>> scripts work fine, by the way. The scope and FM receive scripts run >>> fine, but I hear just hear/see static. If I set the oscope to 900MHz and >>> bring my cordless 900MHz phone around, there's no change in the scope. >>> If I can the entire FM spectrum in the other script, I don't get >>> anything but static anywhere. My little portable CD player can hear the >>> radio just fine in this lab, so I figure the foot-long copper antenna >>> that came with the USRP ought to as well. I don't know a lot about >>> communications... >>> >>> >>> Also, the different test_digital_loopback and test_counting scripts seem >>> to not work very well at all. I don't know if they're expected to, but >>> about 50% of the tests that look vaguely "expected 517, got 0" fail. >>> >>> >>> Is there any advice you can offer as to how to determine what, if >>> anything, is wrong here? >>> >>> Thanks, >>> >>> Dan >>> >>> >>> ___ >>> Discuss-gnuradio mailing list >>> Discuss-gnuradio@gnu.org >>> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio >>> >>> >>> >> >> > > > > ___ > Discuss-gnuradio mailing list > Discuss-gnuradio@gnu.org > http://lists.gnu.org/mailman/listinfo/discuss-gnuradio > > -- View this message in context: http://www.nabble.com/Help-getting-started-tf2432797.html#a6784608 Sent from the GnuRadio mailing list archive at Nabble.com. ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
Re: [Discuss-gnuradio] Help getting started
Well, I've never used the TX boards before, but looking through the files I found fm_tx.py, which makes narrow band fm. You may have to use usrp_nbfm_rcv.py (or whatever it's called) to pick it up, but now I'm just guessing. -Written Dan Halperin wrote: > > Fair enough; I figured since my officemate's pocket CD player could pick > up FM radio the big ole' antenna ought to be able to. > > Is there a script to make a custom FM station using a BasicTX board (I > have another USRP if necessary) to get around that problem? > > -Dan > > Written wrote: >> Well, all I can think of is using the basic rx daugtherboard along with >> usrp_wfm_rcv.py and tuning to some local FM stations, or using the scope, >> but it sounds like you've already done that pretty much. Make sure the >> gain >> on the scope is set to about mid-point for the specific daughterboard >> being >> used. I had the best luck with this. >> >> Depending on your scanning bandwidth, I don't know if you'll actually >> pick >> up any listenable stations, so I'd just use the aforementioned file for >> FM >> testing purposes. >> >> Written >> >> >> Dan Halperin wrote: >> >>> I've used the 2.4GHz RX/TX board, but I have since been using the Basic >>> RX and Basic TX boards. >>> >>> -Dan >>> >>> Written wrote: >>> Hi Dan, What daughterboards are you using? Thanks, Written Dan Halperin wrote: > Hi all, > > I'm just beginning grad school and trying to get my USRP board up and > running so I can start playing. I've tested our equipment on two > different machines now; one an older box running FC4, 512MB ram, with > an > Intel(R) Celeron(R) CPU 2.40GHz. I've also tried one on a newer laptop > (compaq v3000 series) running Gentoo Linux, with 2GB of memory. I've > had > /all kinds/ of interesting phenomena: > > I first tried installing the way on the old wiki > http://www.comsec.com/wiki?UniversalSoftwareRadioPeripheral (first > link > on Google for USRP), and then again using the new say (svn source > checkout using the instructions on the new wiki), on both machines. On > the older machine, I don't get any rx/tx over/underruns (or maybe just > one when initializing) and a throughput of 32MB/s in both directions, > and on the laptop I get exactly 41 under/over runs with a throughput > of > ~31MB/s in the RX direction and around 24 in the TX direction. As far > as > I could tell, these used the same version of the source, but then > again > the SVN repository has jumped from rev. 3772 to rev. 3785 since > yesterday morning. > > Anyway, installation, make check, and the ./test_standard_?x scripts > work fine (the LED behaves as expected and the benchmarks seem > reasonable), however I get nothing when running the usrp_oscope or > usrp_wfm_rcv scripts as directed in the instructions. Both dial tone > scripts work fine, by the way. The scope and FM receive scripts run > fine, but I hear just hear/see static. If I set the oscope to 900MHz > and > bring my cordless 900MHz phone around, there's no change in the scope. > If I can the entire FM spectrum in the other script, I don't get > anything but static anywhere. My little portable CD player can hear > the > radio just fine in this lab, so I figure the foot-long copper antenna > that came with the USRP ought to as well. I don't know a lot about > communications... > > > Also, the different test_digital_loopback and test_counting scripts > seem > to not work very well at all. I don't know if they're expected to, but > about 50% of the tests that look vaguely "expected 517, got 0" fail. > > > Is there any advice you can offer as to how to determine what, if > anything, is wrong here? > > Thanks, > > Dan > > > ___ > Discuss-gnuradio mailing list > Discuss-gnuradio@gnu.org > http://lists.gnu.org/mailman/listinfo/discuss-gnuradio > > > > >>> >>> ___ >>> Discuss-gnuradio mailing list >>> Discuss-gnuradio@gnu.org >>> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio >>> >>> >>> >> >> > > > > ___ > Discuss-gnuradio mailing list > Discuss-gnuradio@gnu.org > http://lists.gnu.org/mailman/listinfo/discuss-gnuradio > > -- View this message in context: http://www.nabble.com/Help-getting-started-tf2432797.html#a6785003 Sent from the GnuRadio mailing list archive at Nabble.com. ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
Re: [Discuss-gnuradio] Help getting started
Fair enough; I figured since my officemate's pocket CD player could pick up FM radio the big ole' antenna ought to be able to. Is there a script to make a custom FM station using a BasicTX board (I have another USRP if necessary) to get around that problem? -Dan Written wrote: Well, all I can think of is using the basic rx daugtherboard along with usrp_wfm_rcv.py and tuning to some local FM stations, or using the scope, but it sounds like you've already done that pretty much. Make sure the gain on the scope is set to about mid-point for the specific daughterboard being used. I had the best luck with this. Depending on your scanning bandwidth, I don't know if you'll actually pick up any listenable stations, so I'd just use the aforementioned file for FM testing purposes. Written Dan Halperin wrote: I've used the 2.4GHz RX/TX board, but I have since been using the Basic RX and Basic TX boards. -Dan Written wrote: Hi Dan, What daughterboards are you using? Thanks, Written Dan Halperin wrote: Hi all, I'm just beginning grad school and trying to get my USRP board up and running so I can start playing. I've tested our equipment on two different machines now; one an older box running FC4, 512MB ram, with an Intel(R) Celeron(R) CPU 2.40GHz. I've also tried one on a newer laptop (compaq v3000 series) running Gentoo Linux, with 2GB of memory. I've had /all kinds/ of interesting phenomena: I first tried installing the way on the old wiki http://www.comsec.com/wiki?UniversalSoftwareRadioPeripheral (first link on Google for USRP), and then again using the new say (svn source checkout using the instructions on the new wiki), on both machines. On the older machine, I don't get any rx/tx over/underruns (or maybe just one when initializing) and a throughput of 32MB/s in both directions, and on the laptop I get exactly 41 under/over runs with a throughput of ~31MB/s in the RX direction and around 24 in the TX direction. As far as I could tell, these used the same version of the source, but then again the SVN repository has jumped from rev. 3772 to rev. 3785 since yesterday morning. Anyway, installation, make check, and the ./test_standard_?x scripts work fine (the LED behaves as expected and the benchmarks seem reasonable), however I get nothing when running the usrp_oscope or usrp_wfm_rcv scripts as directed in the instructions. Both dial tone scripts work fine, by the way. The scope and FM receive scripts run fine, but I hear just hear/see static. If I set the oscope to 900MHz and bring my cordless 900MHz phone around, there's no change in the scope. If I can the entire FM spectrum in the other script, I don't get anything but static anywhere. My little portable CD player can hear the radio just fine in this lab, so I figure the foot-long copper antenna that came with the USRP ought to as well. I don't know a lot about communications... Also, the different test_digital_loopback and test_counting scripts seem to not work very well at all. I don't know if they're expected to, but about 50% of the tests that look vaguely "expected 517, got 0" fail. Is there any advice you can offer as to how to determine what, if anything, is wrong here? Thanks, Dan ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
Re: [Discuss-gnuradio] Help getting started
I've used the 2.4GHz RX/TX board, but I have since been using the Basic RX and Basic TX boards. -Dan Written wrote: Hi Dan, What daughterboards are you using? Thanks, Written Dan Halperin wrote: Hi all, I'm just beginning grad school and trying to get my USRP board up and running so I can start playing. I've tested our equipment on two different machines now; one an older box running FC4, 512MB ram, with an Intel(R) Celeron(R) CPU 2.40GHz. I've also tried one on a newer laptop (compaq v3000 series) running Gentoo Linux, with 2GB of memory. I've had /all kinds/ of interesting phenomena: I first tried installing the way on the old wiki http://www.comsec.com/wiki?UniversalSoftwareRadioPeripheral (first link on Google for USRP), and then again using the new say (svn source checkout using the instructions on the new wiki), on both machines. On the older machine, I don't get any rx/tx over/underruns (or maybe just one when initializing) and a throughput of 32MB/s in both directions, and on the laptop I get exactly 41 under/over runs with a throughput of ~31MB/s in the RX direction and around 24 in the TX direction. As far as I could tell, these used the same version of the source, but then again the SVN repository has jumped from rev. 3772 to rev. 3785 since yesterday morning. Anyway, installation, make check, and the ./test_standard_?x scripts work fine (the LED behaves as expected and the benchmarks seem reasonable), however I get nothing when running the usrp_oscope or usrp_wfm_rcv scripts as directed in the instructions. Both dial tone scripts work fine, by the way. The scope and FM receive scripts run fine, but I hear just hear/see static. If I set the oscope to 900MHz and bring my cordless 900MHz phone around, there's no change in the scope. If I can the entire FM spectrum in the other script, I don't get anything but static anywhere. My little portable CD player can hear the radio just fine in this lab, so I figure the foot-long copper antenna that came with the USRP ought to as well. I don't know a lot about communications... Also, the different test_digital_loopback and test_counting scripts seem to not work very well at all. I don't know if they're expected to, but about 50% of the tests that look vaguely "expected 517, got 0" fail. Is there any advice you can offer as to how to determine what, if anything, is wrong here? Thanks, Dan ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
Re: [Discuss-gnuradio] Help getting started
Hi Dan, What daughterboards are you using? Thanks, Written Dan Halperin wrote: > > Hi all, > > I'm just beginning grad school and trying to get my USRP board up and > running so I can start playing. I've tested our equipment on two > different machines now; one an older box running FC4, 512MB ram, with an > Intel(R) Celeron(R) CPU 2.40GHz. I've also tried one on a newer laptop > (compaq v3000 series) running Gentoo Linux, with 2GB of memory. I've had > /all kinds/ of interesting phenomena: > > I first tried installing the way on the old wiki > http://www.comsec.com/wiki?UniversalSoftwareRadioPeripheral (first link > on Google for USRP), and then again using the new say (svn source > checkout using the instructions on the new wiki), on both machines. On > the older machine, I don't get any rx/tx over/underruns (or maybe just > one when initializing) and a throughput of 32MB/s in both directions, > and on the laptop I get exactly 41 under/over runs with a throughput of > ~31MB/s in the RX direction and around 24 in the TX direction. As far as > I could tell, these used the same version of the source, but then again > the SVN repository has jumped from rev. 3772 to rev. 3785 since > yesterday morning. > > Anyway, installation, make check, and the ./test_standard_?x scripts > work fine (the LED behaves as expected and the benchmarks seem > reasonable), however I get nothing when running the usrp_oscope or > usrp_wfm_rcv scripts as directed in the instructions. Both dial tone > scripts work fine, by the way. The scope and FM receive scripts run > fine, but I hear just hear/see static. If I set the oscope to 900MHz and > bring my cordless 900MHz phone around, there's no change in the scope. > If I can the entire FM spectrum in the other script, I don't get > anything but static anywhere. My little portable CD player can hear the > radio just fine in this lab, so I figure the foot-long copper antenna > that came with the USRP ought to as well. I don't know a lot about > communications... > > > Also, the different test_digital_loopback and test_counting scripts seem > to not work very well at all. I don't know if they're expected to, but > about 50% of the tests that look vaguely "expected 517, got 0" fail. > > > Is there any advice you can offer as to how to determine what, if > anything, is wrong here? > > Thanks, > > Dan > > > ___ > Discuss-gnuradio mailing list > Discuss-gnuradio@gnu.org > http://lists.gnu.org/mailman/listinfo/discuss-gnuradio > > -- View this message in context: http://www.nabble.com/Help-getting-started-tf2432797.html#a6784198 Sent from the GnuRadio mailing list archive at Nabble.com. ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
[Discuss-gnuradio] Help getting started
Hi all, I'm just beginning grad school and trying to get my USRP board up and running so I can start playing. I've tested our equipment on two different machines now; one an older box running FC4, 512MB ram, with an Intel(R) Celeron(R) CPU 2.40GHz. I've also tried one on a newer laptop (compaq v3000 series) running Gentoo Linux, with 2GB of memory. I've had /all kinds/ of interesting phenomena: I first tried installing the way on the old wiki http://www.comsec.com/wiki?UniversalSoftwareRadioPeripheral (first link on Google for USRP), and then again using the new say (svn source checkout using the instructions on the new wiki), on both machines. On the older machine, I don't get any rx/tx over/underruns (or maybe just one when initializing) and a throughput of 32MB/s in both directions, and on the laptop I get exactly 41 under/over runs with a throughput of ~31MB/s in the RX direction and around 24 in the TX direction. As far as I could tell, these used the same version of the source, but then again the SVN repository has jumped from rev. 3772 to rev. 3785 since yesterday morning. Anyway, installation, make check, and the ./test_standard_?x scripts work fine (the LED behaves as expected and the benchmarks seem reasonable), however I get nothing when running the usrp_oscope or usrp_wfm_rcv scripts as directed in the instructions. Both dial tone scripts work fine, by the way. The scope and FM receive scripts run fine, but I hear just hear/see static. If I set the oscope to 900MHz and bring my cordless 900MHz phone around, there's no change in the scope. If I can the entire FM spectrum in the other script, I don't get anything but static anywhere. My little portable CD player can hear the radio just fine in this lab, so I figure the foot-long copper antenna that came with the USRP ought to as well. I don't know a lot about communications... Also, the different test_digital_loopback and test_counting scripts seem to not work very well at all. I don't know if they're expected to, but about 50% of the tests that look vaguely "expected 517, got 0" fail. Is there any advice you can offer as to how to determine what, if anything, is wrong here? Thanks, Dan ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org http://lists.gnu.org/mailman/listinfo/discuss-gnuradio