Re: [Drakelist] Drake R-4b upgrade

2011-09-27 Thread Garey Barrell

Guillermo -

I tried to send you a direct message last night, but was refused by your ISP.  Do you have another 
address that will work?


73, Garey - K4OAH
Glen Allen, VA

Drake 2-B, 2-C/2-NT, 4-A, 4-B, C-Line
and TR-4/C Service Supplement CDs
www.k4oah.com


GGLL wrote:

Hello Garey, my name is Guillermo, LU8EYW/W in Puerto Madryn, Chubut 
province, Argentina.

I'm troubleshooting my R-4B receiver and searching the schematic, the model 
which has the OB2
regulator voltage included (V11) and a PCB board not included in the first 
models (or at least,
different as I'm seeing in various different schematics already downloaded). In 
my receiver, this
regulator tube is located between front panel and V2.

So far, I've had no luck yet, but found and downloaded three
different copies, no one of these has the OB2 regulator tube.

Furthermore, I've supposed my R-4b to be a later serial number model, but 
looking photographs
at Drake virtual museum, I see one which has a larger serial number than mine, 
but no OB2!
(looking in detail, you can see just printed OB2 onto the chassis, only).

Can you enlighten me about which version of this receiver had this upgrade?.

Many thanks in advance

Regards
Guillermo - LU8EYW/W.



___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist


Re: [Drakelist] Drake R-4b upgrade

2011-09-27 Thread Garey Barrell

Guillermo -

Actually the 0B2 was a 'downgrade' that was only used in the first 1000 (s/n 7000 - 7999).  It was 
holdover from the R-4A which still had a tube based CALIBRATOR that needed the 'regulated' +150 
VDC.  Starting with the R-4B, the CAL circuit was changed to an FET with RTL dividers to provide 25 
kHz markers, meaning the 0B2 was no longer needed.  The lower voltage stages had their own Zener 
regulator, (BAND, PTO and CAL,) and this was supplied direct from the 'un-regulated' +150V bus.  I 
guess it took the first 1000 units for Drake to realize that the 0B2 no longer contributed any 
improvement and could be removed!!


So your R-4B is one of the first 1000, with a s/n in the 7000 range.  There are other changes in 
later versions, such as changing the oscillator in the PTO from bipolar to FET for improved stability.


If you can get me a good email address, I can send you the correct schematic.

73, Garey - K4OAH
Glen Allen, VA

Drake 2-B, 2-C/2-NT, 4-A, 4-B, C-Line
and TR-4/C Service Supplement CDs
www.k4oah.com


GGLL wrote:

Hello Garey, my name is Guillermo, LU8EYW/W in Puerto Madryn, Chubut 
province, Argentina.

I'm troubleshooting my R-4B receiver and searching the schematic, the model which has the OB2 
regulator voltage included (V11) and a PCB board not included in the first models (or at least, 
different as I'm seeing in various different schematics already downloaded). In my receiver, this 
regulator tube is located between front panel and V2.


So far, I've had no luck yet, but found and downloaded three
different copies, no one of these has the OB2 regulator tube.

Furthermore, I've supposed my R-4b to be a later serial number model, but looking photographs 
at Drake virtual museum, I see one which has a larger serial number than mine, but no OB2! 
(looking in detail, you can see just printed OB2 onto the chassis, only).


Can you enlighten me about which version of this receiver had this upgrade?.

Many thanks in advance

Regards
Guillermo - LU8EYW/W.



___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist