[Elecraft] Noise Blanker with SVGA/P3

[zumbruns]

Any idea when the Noise blanker will be implemented in the P3SVGA option?  For 
those of us with much noise the Noise Blanker in the P3 was a very nice 
feature.  I would really like to see it in my monitor when I use SVGA on 
digital modes.  Thanks and 73, Steve W0SZ 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3: Rough audio with amp even using voice recorder- SOLVED

[Jim Brown]

On Wed,9/17/2014 6:19 PM, Ignacy wrote:

Very good suggestions. When listening on teh other radio, I used your
settings and added 4 db to 1.6 and 2.4. But could sound only good with my
ears that have some treble weakness.


I don't usually recommend boosting the highs except for a pro mic that 
needs it for ham radio. While it may sound better for your hearing loss, 
it can cause overload of the audio path.



But CM500 1 inch and 2 inches away sound completely different.


Yes. I always recommend that the mic be 2-3 inches above and to the side 
of the mouth. This avoids bass build-up from being too close, and also 
breath pops.


73, Jim K9YC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3: Rough audio with amp even using voice recorder- SOLVED

[Don Wilhelm]

The TXEQ settings for the KX3 are the same as for the K3.

73,
Don W3FPR

On 9/17/2014 9:16 PM, Walter Underwood wrote:

For those of us with a KX3 instead of a K3, what would be the frequency cutoff 
for “three lowest bands”?

wunder
K6WRU
CM87wj
http://observer.wunderwood.org/

On Sep 17, 2014, at 5:52 PM, Jim Brown  wrote:


On Wed,9/17/2014 3:52 PM, Ignacy wrote:

I also found by testing on the other radio that CM500 sounds very different
close (bassy) and a bit apart (more balanced).

For most voices, a good starting point for TXEQ with the CM500 is to fully cut 
the lowest three bands, cut the 4th band about 6dB, leave all the others at 0 
dB. Then get some critical signal reports from hams you trust to have good ears.

73, Jim K9YC
__



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3: Rough audio with amp even using voice recorder- SOLVED

[Ignacy]

Very good suggestions. When listening on teh other radio, I used your
settings and added 4 db to 1.6 and 2.4. But could sound only good with my
ears that have some treble weakness.

But CM500 1 inch and 2 inches away sound completely different.

Ignacy

On Wed, Sep 17, 2014 at 8:53 PM, Jim Brown-10 [via Elecraft] <
ml-node+s365791n7593180...@n2.nabble.com> wrote:

> On Wed,9/17/2014 3:52 PM, Ignacy wrote:
> > I also found by testing on the other radio that CM500 sounds very
> different
> > close (bassy) and a bit apart (more balanced).
>
> For most voices, a good starting point for TXEQ with the CM500 is to
> fully cut the lowest three bands, cut the 4th band about 6dB, leave all
> the others at 0 dB. Then get some critical signal reports from hams you
> trust to have good ears.
>
> 73, Jim K9YC
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
> 
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
> 
>
>
> --
>  If you reply to this email, your message will be added to the discussion
> below:
>
> http://elecraft.365791.n2.nabble.com/K3-Rough-audio-with-amp-even-using-voice-recorder-SOLVED-tp7593179p7593180.html
>  To unsubscribe from K3: Rough audio with amp even using voice recorder-
> SOLVED, click here
> 
> .
> NAML
> 
>




--
View this message in context: 
http://elecraft.365791.n2.nabble.com/K3-Rough-audio-with-amp-even-using-voice-recorder-SOLVED-tp7593179p7593181.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3: Rough audio with amp even using voice recorder- SOLVED

[Walter Underwood]

For those of us with a KX3 instead of a K3, what would be the frequency cutoff 
for “three lowest bands”?

wunder
K6WRU
CM87wj
http://observer.wunderwood.org/

On Sep 17, 2014, at 5:52 PM, Jim Brown  wrote:

> On Wed,9/17/2014 3:52 PM, Ignacy wrote:
>> I also found by testing on the other radio that CM500 sounds very different
>> close (bassy) and a bit apart (more balanced).
> 
> For most voices, a good starting point for TXEQ with the CM500 is to fully 
> cut the lowest three bands, cut the 4th band about 6dB, leave all the others 
> at 0 dB. Then get some critical signal reports from hams you trust to have 
> good ears.
> 
> 73, Jim K9YC
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to wun...@wunderwood.org

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3: Rough audio with amp even using voice recorder- SOLVED

[Jim Brown]

On Wed,9/17/2014 3:52 PM, Ignacy wrote:

I also found by testing on the other radio that CM500 sounds very different
close (bassy) and a bit apart (more balanced).


For most voices, a good starting point for TXEQ with the CM500 is to 
fully cut the lowest three bands, cut the 4th band about 6dB, leave all 
the others at 0 dB. Then get some critical signal reports from hams you 
trust to have good ears.


73, Jim K9YC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3: Rough audio with amp even using voice recorder- SOLVED

[Ignacy]

KPA3 had only 100mA idle current. After adjusting to 400mA (R11 on top of
KPA3) the signal is very good at any power level.

I also found by testing on the other radio that CM500 sounds very different
close (bassy) and a bit apart (more balanced). 

Thank you all for the comments. 

Ignacy, NO9E



--
View this message in context: 
http://elecraft.365791.n2.nabble.com/K3-Rough-audio-with-amp-even-using-voice-recorder-SOLVED-tp7593179.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Heil Proset

[Mike Goldstein]

Using the K3, has anyone else had problems with the Heil Proset 
supplied by Elecraft (model iC) as to audio feedback on VOX, very 
sensitive controls of VOX gain and Mic gain, etc. etc?


These problems can be masked as RFI, but adding toroids on the cable 
has little effect. No other microphones seem to have these problems.


I've wrestled with this for 6 years, and finally decided to beat it. 
I had the same problems on my Kenwood TS590, with this headset.


I have the solution.  Email directly to mg...@pathcom.com, if you 
wish, as I don't receive email from the Elecraft reflector.


73 Mike VE3GFN

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] (no subject)

[michealgee]

Sent from Samsung Mobile
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KX3 Schematic for KX3BNCMDKT ?

[Hans H Vollmer]

Hi Fellow Elecrafters,

is there a schematic for the Mod-Kit KX3BNCMDKT available ?
 Tnx for any answer.

73 de Hans, DF5SR
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] CW on ssbHello Everyone,

[Matt VK2RQ]

MN012;SWT019;MN255;
(assuming KX3, since the procedure below applies to that radio)

73,
Matt VK2RQ

> On 17 Sep 2014, at 9:41 pm, Poul Erik Karlshøj (PKA)  wrote:
> 
> Could someone please write a Macro that does that?
> 73/OZ4UN
> 
>> Den 16/09/2014 kl. 13.58 skrev "Charles Tropp via Elecraft" 
>> :
>> 
>> On the Configuration Menu go to CW WGHT SSB-CW. Tapping the 1 key toggles 
>> between SSB+CW, which allows CW to be sent when in SSB Mode and SSB-CW, 
>> which doesn't. The other station operating SSB will hear your signal at the 
>> tone sent by your sidetone pitch.
>> 
>> 73, Charles N2SO
>> 
>>> On Tuesday, September 16, 2014 7:43:00 AM, Gerry leary wrote:
>>> 
>>> I am trying to find the place in the menu system where I can turn on the CW 
>>> while in SSB mode is located.  I have heard that it is in the CW features 
>>> but I find nothing there.  Can anyone tell me how to find this?  Gerry 
>>> Leary who hopes that Elecraft implements the rest of the CW read out 
>>> feature.
>>> 
>>> Sent from my iPhone this time
>>> __
>>> Elecraft mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>> Help: http://mailman.qth.net/mmfaq.htm
>>> Post: mailto:Elecraft@mailman.qth.net
>>> 
>>> This list hosted by: http://www.qsl.net
>>> Please help support this email list: http://www.qsl.net/donate.html
>>> Message delivered to charlestr...@yahoo.com
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to p...@tele.gl
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to matt.vk...@gmail.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] CW on ssbHello Everyone,

[PKA]

Could someone please write a Macro that does that?
73/OZ4UN

> Den 16/09/2014 kl. 13.58 skrev "Charles Tropp via Elecraft" 
> :
> 
> On the Configuration Menu go to CW WGHT SSB-CW. Tapping the 1 key toggles 
> between SSB+CW, which allows CW to be sent when in SSB Mode and SSB-CW, which 
> doesn't. The other station operating SSB will hear your signal at the tone 
> sent by your sidetone pitch.
> 
> 73, Charles N2SO
> 
>> On Tuesday, September 16, 2014 7:43:00 AM, Gerry leary wrote:
>> 
>> I am trying to find the place in the menu system where I can turn on the CW 
>> while in SSB mode is located.  I have heard that it is in the CW features 
>> but I find nothing there.  Can anyone tell me how to find this?  Gerry Leary 
>> who hopes that Elecraft implements the rest of the CW read out feature.
>> 
>> Sent from my iPhone this time
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to charlestr...@yahoo.com
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to p...@tele.gl
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com