Re: [Elecraft] P3 Transmit Monitor Option
Roy, The short answer is NO. The modulation envelope display is good for displaying any clipping, but it will not show you the frequency response. If you have seen the modulation envelope of an SSB signal on an oscilloscope, that is what you can expect, it shows relative amplitude and any flattopping, but it does not show a spectrum display. The best way to evaluate your transmit audio is to listen to your transmit signal on another receiver. Feed the K3 into a dummy load and listen on another receiver with a short wire for an antenna - you are striving for an S-9 to S9+10 level in the monitor receiver. After it sounds good to you in the monitor receiver, then solicit audio reports from folks on the air who know what your natural (not on the air) voice sounds like. That will produce the best audio TX EQ settings for you and your microphone. Change microphones and you may need a whole set of TX EQ settings. 73, Don W3FPR On 5/20/2015 8:47 PM, Roy Morris wrote: Is it possible to optimize TXEQ settings for best sounding audio in SSB mode using the modulation envelope display? Roy Morris W4WFB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] 'tude
I no longer play rugby or test hand-grenades, so I welcome the occasional jousting on the reflector. Wayne N6KR On May 20, 2015, at 11:29 AM, Brian wrote: > No more grouchy than usual...I think. > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules
Am 20.05.2015 um 02:29 schrieb Wayne Burdick: * LINE IN/OUT AUDIO USE WITH USB PORT (K3S, KIO3B): If a plug is inserted into the LINE IN jack on the K3S, this audio signal will override the digitized audio line-in data that is present in the USB cable. LINE OUT on the K3S, however, is always available even if the USB cable is being used for line-out. I can already see the "Help! I don't get any audio from my USB connection!" emails on the reflector. ;-) Wayne: If you're ever going to redesign the I/O module again (KIO3C anyone? ;-)) please make that a menu selection and also store different settings, i.e. line/mic gain for USB audio and line/mic gain for the 3,5 mm connection. That's one of the really neat things I like on a friend's TS-590. ;-) 73, Olli - DH8BQA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] 'tude
Yes! And the two fingers I use are fully extended thumb and pinky. 73, Mike NF4L > On May 20, 2015, at 1:53 PM, GRANT YOUNGMAN wrote: > > >> On May 20, 2015, at 12:46 PM, Mike Reublin NF4L wrote: >> >> Is it just me, or has it been a tad testy here since the announcement of the >> K3S? >> >> 73, Mike NF4L > > It does seem like a comfortable chair, a good book, and two fingers of good > Scotch are in order … or maybe just a deep breath :-) > > Grant NQ5T __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules
The present firmware release has very little impact on the K3, but it is still
important to test each release to make sure we didn't break anything. We've had
some positive reports in that regard, so no need for everyone to load it.
73,
Wayne
N6KR
On May 20, 2015, at 11:00 AM, Phil Wheeler wrote:
> That's my interpretation, Ross. Just asking Wayne for confirmation.
>
> Hmmm .. but I wonder if anyone has been able to add such items to their K3 as
> yet? They were announced a week ago, and my impression is that they may be in
> short supply for K3 usage for a while.
>
> Phil W7OX
>
> On 5/20/15 10:29 AM, Ross Primrose wrote:
>> The new firmware would be required for a K3 IF you add any of the newly
>> upgraded K3S pieces to your K3, such as the new KIO3, KXV3B or KAT3A.
>>
>> 73, Ross N4RP
>>
>> On 5/20/2015 10:32 AM, Phil Wheeler wrote:
>>> Wayne,
>>>
>>> It's unclear what impact, if any, this firmware will have on the K3. All
>>> the specifics listed below appear to be K3S related.
>>>
>>> I usually load beta versions *only* if the test/change relates to some
>>> feature I really want. If no changes for K3, no reason for me to load it.
>>>
>>> Is there any reason a K3 needs this version for improved performance,
>>> functionality, etc.?
>>>
>>> 73, Phil W7OX
>>>
>>> On 5/19/15 5:29 PM, Wayne Burdick wrote:
Hi all,
K3 beta firmware rev. 5.26 is now available on our K3 software page. This
is the first combined K3/K3S firmware release. It can be loaded into
either transceiver using K3 Utility.
Some firmware features and changes apply only to the K3S, or to the
various updated internal modules, as described in the release notes below.
(Further details will be provided in the K3S owner's manual and other
documents as they are made available.) We appreciate any firmware testing
you might do on a K3, with or without any upgraded modules.
73,
Wayne
N6KR
* * *
K3/K3S MCU rev. 5.26
* USB COMPUTER PORT FOR COMBINED CONTROL and DIGITAL AUDIO (K3S, KIO3B):
If a KIO3B module is installed (standard with the K3S), the CONFIG:RS232
menu entry will have a "USB" setting. If this setting is used, then a
single USB cable can be used between the K3S and a computer to provide
remote control, digitized line-level audio in/out, and PTT/KEY (via
equivalents to the "RTS" and "DTR" signals). All of these signals are
usually recognized by computer applications that also support RS232. This
eliminates the need for a sound card and associated analog line in/out
cables, as well as any external converter units. Refer to the K3S owner's
manual, pgs. 18-20, for details.
* NEW P3 PANADAPTER CABLE SUPPORT (K3S, KIO3B): If a KIO3B module is
installed, then the P3 Panadapter must be connected to the K3S at its
RS232/P3 connector (RJ45). Two different special cables are available for
this purpose, depending on whether a computer will be connected via USB or
RS232 to the K3S and P3. Refer to the K3S owner's manual for details (pg.
18 and 19).
* LINE IN/OUT AUDIO USE WITH USB PORT (K3S, KIO3B): If a plug is inserted
into the LINE IN jack on the K3S, this audio signal will override the
digitized audio line-in data that is present in the USB cable. LINE OUT on
the K3S, however, is always available even if the USB cable is being used
for line-out.
* PREAMP 2 and CONFIG:PREAMP2 MENU ENTRY (KXV3B): This menu entry is only
applicable if a KXV3B module is installed (supplied with the K3S). It also
only applies if the current band is 12, 10, or 6 meters. If PREAMP2 is set
to ON, then the PRE switch rotates through settings of OFF, PRE 1, and PRE
2 on the applicable band. PRE 2 turns on the low-noise preamp on the
KXV3B module (+20 dB, with a typical NF of -144 dBm on 12/10/6 meters).
When PRE 2 is selected, the PRE icon will flash slowly. Note: Do not use
an external preamplifier (such as an Elecraft PR6 or PR6-10) when using
the built-in low-noise preamp (PRE 2). This would result in excessive
gain. .
* MULTIPLE ATTENUATOR SETTINGS and MAIN:ATTEN MENU ENTRY (K3S RF BOARD):
On a K3S, the MAIN:ATTEN menu entry is used to select the per-band
attenuation level for the ATTN switch (5/10/15 dB). A shortcut method of
accessing this menu entry is to hold the ATTN switch for about 3 seconds.
(On a K3, the parameter is fixed at 10 dB.)
* LOW-LOSS ATU BYPASS SETTING (KAT3A): The upgraded internal ATU option,
the KAT3A, includes a very low-loss bypass path via an additional relay.
The bypass relay is engaged when the ATU switch is used to turn the ATU
icon OFF. This setting can be used with closely matched antennas.
("Bypass" mode on the
Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules
The K3S FAQ indicates that the KXV3B, KAT3A & KBPF3A are available now.
I can't confirm or deny the accuracy of that. But, I believe you'd need
the new beta firmware for any of those.
73, Ross N4RP
On 5/20/2015 2:00 PM, Phil Wheeler wrote:
That's my interpretation, Ross. Just asking Wayne for confirmation.
Hmmm .. but I wonder if anyone has been able to add such items to
their K3 as yet? They were announced a week ago, and my impression is
that they may be in short supply for K3 usage for a while.
Phil W7OX
On 5/20/15 10:29 AM, Ross Primrose wrote:
The new firmware would be required for a K3 IF you add any of the
newly upgraded K3S pieces to your K3, such as the new KIO3, KXV3B or
KAT3A.
73, Ross N4RP
On 5/20/2015 10:32 AM, Phil Wheeler wrote:
Wayne,
It's unclear what impact, if any, this firmware will have on the K3.
All the specifics listed below appear to be K3S related.
I usually load beta versions *only* if the test/change relates to
some feature I really want. If no changes for K3, no reason for me
to load it.
Is there any reason a K3 needs this version for improved
performance, functionality, etc.?
73, Phil W7OX
On 5/19/15 5:29 PM, Wayne Burdick wrote:
Hi all,
K3 beta firmware rev. 5.26 is now available on our K3 software
page. This is the first combined K3/K3S firmware release. It can be
loaded into either transceiver using K3 Utility.
Some firmware features and changes apply only to the K3S, or to the
various updated internal modules, as described in the release notes
below. (Further details will be provided in the K3S owner's manual
and other documents as they are made available.) We appreciate any
firmware testing you might do on a K3, with or without any upgraded
modules.
73,
Wayne
N6KR
* * *
K3/K3S MCU rev. 5.26
* USB COMPUTER PORT FOR COMBINED CONTROL and DIGITAL AUDIO (K3S,
KIO3B): If a KIO3B module is installed (standard with the K3S), the
CONFIG:RS232 menu entry will have a "USB" setting. If this setting
is used, then a single USB cable can be used between the K3S and a
computer to provide remote control, digitized line-level audio
in/out, and PTT/KEY (via equivalents to the "RTS" and "DTR"
signals). All of these signals are usually recognized by computer
applications that also support RS232. This eliminates the need for
a sound card and associated analog line in/out cables, as well as
any external converter units. Refer to the K3S owner's manual, pgs.
18-20, for details.
* NEW P3 PANADAPTER CABLE SUPPORT (K3S, KIO3B): If a KIO3B module
is installed, then the P3 Panadapter must be connected to the K3S
at its RS232/P3 connector (RJ45). Two different special cables are
available for this purpose, depending on whether a computer will be
connected via USB or RS232 to the K3S and P3. Refer to the K3S
owner's manual for details (pg. 18 and 19).
* LINE IN/OUT AUDIO USE WITH USB PORT (K3S, KIO3B): If a plug is
inserted into the LINE IN jack on the K3S, this audio signal will
override the digitized audio line-in data that is present in the
USB cable. LINE OUT on the K3S, however, is always available even
if the USB cable is being used for line-out.
* PREAMP 2 and CONFIG:PREAMP2 MENU ENTRY (KXV3B): This menu entry
is only applicable if a KXV3B module is installed (supplied with
the K3S). It also only applies if the current band is 12, 10, or 6
meters. If PREAMP2 is set to ON, then the PRE switch rotates
through settings of OFF, PRE 1, and PRE 2 on the applicable band.
PRE 2 turns on the low-noise preamp on the KXV3B module (+20 dB,
with a typical NF of -144 dBm on 12/10/6 meters). When PRE 2 is
selected, the PRE icon will flash slowly. Note: Do not use an
external preamplifier (such as an Elecraft PR6 or PR6-10) when
using the built-in low-noise preamp (PRE 2). This would result in
excessive gain. .
* MULTIPLE ATTENUATOR SETTINGS and MAIN:ATTEN MENU ENTRY (K3S RF
BOARD): On a K3S, the MAIN:ATTEN menu entry is used to select the
per-band attenuation level for the ATTN switch (5/10/15 dB). A
shortcut method of accessing this menu entry is to hold the ATTN
switch for about 3 seconds. (On a K3, the parameter is fixed at 10
dB.)
* LOW-LOSS ATU BYPASS SETTING (KAT3A): The upgraded internal ATU
option, the KAT3A, includes a very low-loss bypass path via an
additional relay. The bypass relay is engaged when the ATU switch
is used to turn the ATU icon OFF. This setting can be used with
closely matched antennas. ("Bypass" mode on the earlier model KAT3
ATU uses a minimum-L/minimum-C network setting rather than a relay,
result in a small dissipation loss that varies with frequency.)
* 100-500 KHZ SENSITIVITY IMPROVEMENT (KBPF3A): The KBPF3A is an
upgrade from the KBPF3. The lowest-frequency filter in the KBPF3A
has a cutoff at 100 kHz rather than 500 kHz. This improves typical
sensitivity at 137 kHz (2200 meters) to about -120 dBm, and at 472
kHz (600 meters), about -130 dBm.
* UPDATED "PA" (PREAMP) REMOT
Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules
Milverton M. Swire via Elecraft wrote: What is the saying about an Ant hill and a Mountain? 73 Milverton / Don't you mean Mole Hill? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules
Hi Milverton,
Well I'm old and my grandmother who was always good at repeating those
witticisms used to say, "making mountains out of mole hills". Her way
of saying not important.
73,
Bob
K2TKex KN2TKR (1956 & K2TKR
On 5/20/2015 1:05 PM, Milverton M. Swire via Elecraft wrote:
K3 beta firmware rev. 5.26 is now available on our K3 software page.<<<
Wayne clearly states " BETA"
{ I load those only if they provide some new benefit }
Then WHY the Fuss?
If you had a ICOM, and you send it in for repair, upon return, the Firmware was
updated.Would you query the content of the update? And! What are the benefits
to you?
What is the saying about an Ant hill and a Mountain?
73 Milverton / W9MMS.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com
Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules
Exactly :-) That's why I asked about K3 impacts of this beta software. I only beta test functions which I can test (for radios) within those I use when operating--and especially those for which i have a need. The recent Fixed-Tune mode add to the PX3 comes to mind. Phil W7OX On 5/20/15 9:15 AM, Lynn W. Taylor, WB6UUT wrote: Then you should not beta test. Hopefully someone else will, and they'll catch any bugs that might affect you in the future. 73 -- Lynn On 5/20/2015 8:04 AM, Phil Wheeler wrote: I didn't purchase my Elecraft products to contribute to the greater good. Nor do I plan to spend time loading software from which I will see a change only if there was a problem in that particular beta version (which has happened). __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules
Professional software QC engineers refer to this as "regression testing", to ensure that the software involved continues to operate as it did in the previous release as tested/released on the available hardware at that time. There are no documented changes for the K3, therefore you should not see any difference in the behavior of a K3 when testing this beta firmware on it. If you do not wish to test a beta deployment of an upcoming firmware release, then don't install and test it. If you'd like to help Elecraft verify that the changes made to the firmware behave as expected, then I'm sure they'd appreciate it if you'd install it and try it out. I just wish Yahoo! would do the same thing for its mail software! (I continually see problems in the formatting of my posts the list from my Yahoo! web account; please bear with me/it) 73 de N1HO From: Phil Wheeler Is there any reason a K3 needs this version for improved performance, functionality, etc.? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules
I am not 100% sure of this, but I believe firmware updates are loaded to the Elecraft web page and it is up to us to check for them. I think Wayne's announcement for 5.26 is a 'special' case. I'm sure someone will correct me if this is incorrect. 73, Tom - W4BQF -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Hisashi T Fujinaka Sent: Wednesday, May 20, 2015 12:16 AM To: Phil Wheeler Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules Sorry to be a pest, but can someone look at the email headers of Wayne's announcement and see if there's something odd? For some reason I never get his firmware announcements and I don't even see anhything likely at the mail server. Can someone send me the headers? Thanks. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] FS: K6XX CW Indicator kit
Kit has been spoken for. On Tue, May 19, 2015 at 10:41 PM, Michael Bower wrote: > I came across this unbuilt kit and will likely never use it. So it is for > sale. > > Asking $18 including shipping. US only. > > PayPal, check ok. > > Michael N4NMR > > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] New K3/K3S Beta Firmware, rev. 5.26: Support for K3S and upgraded modules
As for the K3, updates will continue to be for both, I think, and it's worth checking to make sure the K3 doesn't suffer because of the specific K3S additions or changes...even if the update does not add anything for the K3. - Chuck, KE9UW -- View this message in context: http://elecraft.365791.n2.nabble.com/New-K3-K3S-Beta-Firmware-rev-5-26-Support-for-K3S-and-upgraded-modules-tp7603339p7603353.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] anxiously awaiting
I joined this list a few weeks ago to confirm that my choice for a new radio (to replace my 30-year-old TS-440S) was the correct one. All your e-mails confirmed that my choice (a KX3) was correct and I went to Hamvention intending to bring one home. Alas, the cupboard was bare by the time I got to the Elecraft booth, so I took away an order form, filled it out overnight and returned the next day to order a KX3 kit with all of the trimmings including the 2-meter module and the PX3 panadapter. I was impressed that the fellow who took my order form carefully perused it to check to see if what I had ordered was actually what I needed. Turns out that I did not need the two SMA adapters I had included and we expunged it from the order. I have not heard a peep from Elecraft about my order, nor have I seen any related charges on my credit card, so I assume they are catching up from Dayton and will get to my order sooner or later (I hope sooner). Waiting on pins and needles (ouch)! Stan, WA1LOU __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
