Re: [Elecraft] AX1 may add 40 meter coverage with "AXE1" extender
Thanks for Wayne, I would be differently interested. Take my KX3 stuff in my RV and this would definitely be a great addition. - 73 John N0IB KX3 #7432 PX3 #1114 -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] Heil Classic
Is it possible to connect a Heil Classic to a KX3? If so, how? - 73 John (N0IB) -- View this message in context: http://elecraft.365791.n2.nabble.com/Heil-Classic-tp7596623.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Heil Classic
Thanks Found a schematic for combining the mike, foot switch, in a project box. - 73 John (N0IB) -- View this message in context: http://elecraft.365791.n2.nabble.com/Heil-Classic-tp7596623p7596642.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 has Sold
I have sold my K3. Thanks to all that contacted me. - John K3 # 364 -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-For-Sale-tp5933715p6003783.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 For Sale
K3 for sale. In perfect cosmetic and working condition. Non-smoker. Elecraft K3 #364 w/options K3/100 100W Xcvr. (Modular Kit) KAT3K3 ATU (Modular Kit) KBPF3K3 Gen. Cov. RX Module KDVR3K3 Dig. Voice Recorder KFL3A-1.8K K3 1.8 kHz, 8 pole filter KFL3A-2.8K K3 2.8 kHz, 8 pole filter KFL3A-400K3 400 Hz, 8 pole filter KFL3A-6K K3 6 kHz, 8 pole filter KFL3B-FM K3 FM b/w filter KRX3K3 2nd RX 2.7 kHz Filter KFL3A-400 400 Hz, 8 pole filter KTCXO3-1 K3 TCXO (1ppm) KXV3AK3 RX Ant, IF Out Xvrtr Intf. For sale. Best offer. Contact off list please. 73, John N0IB - John K3 # 364 -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-For-Sale-tp5933715p5933715.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Great Service!
How great is the customer service? I ordered some mod kits and in the comment section gave them my K3 # and asked if they thought I might need to do any additional mods. Madelyn replied, I'll go ahead and send you the 180k resistor for the ALC modification - just in case! What a company! Great Business Plan Thanks for the great product. John Glascock K3 #364 - John K3 # 364 -- View this message in context: http://n2.nabble.com/Great-Service%21-tp2120626p2120626.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Vista 64 USB drivers
I had a similar situation with my MacBook Pro running OS X and Vista Bus. with Parallels. I tried the KUSB but could not get the K3 Utility to see the K3 with either Operating System. I purchased the Radio Shack USB to Serial adapter and all work well on both the Mac side and the Vista side until I rebooted the system. Now the Mac side works great but when I go the the Vista side Parallels tells me the USB device is already in use. I have yet to figure out how to release the port in Mac so that Vista can see the USB connection. 73, John, NOIB K3 #364 Dave Van Wallaghen wrote: I noticed some discussion awhile ago about USB drivers for Vista that may or may not work. I had a catastrophic failure of my old Dell laptop and had to order a new one. I ordered a ThinkPad T61 with Vista64 business edition (for many reasons - it's a long story). I was able to find hardware drivers for all of the hardware I interface to and the transition wasn't as bad as I thought it was going to be. I have a 4-port USB hub that feeds a USB Gear 4-port serial converter. This arrangement worked fine under XP even with my K3 and the K3 firmware utility. But with Vista64 I could not run Ham Radio Deluxe connected to my K3. It would hang the laptop after about 20-30 seconds, requiring a hard reboot. I looked through the forum for HRD and found the same problem being discussed, but no solution. And it seemed that it was not a total Vista problem either since a number of people reported that they had no problems at all. So I figured it had to be a driver problem and went looking for updated drivers. The USB Gear serial converter uses an FTDI chip set and so I went to the FTDI website: www.ftdichip.com and found an updated driver: 2.04.06 dated 3/20/2008. (These are now Microsoft certified). After installation, all seems to work just fine. The Elecraft K3 Utility seems to work fine also (I haven't tried updating the firmware yet since I'm current). I also found an updated Prolific driver for the KUSB for Vista64. It installed correctly and reports a new serial com port under Device Manager, but I could not communicate with the K3 through HRD or the K3 utility. They both find the port number ok, but state nothing is there. So I'm not so sure that the driver is a go yet for Vista64 and the KUSB. Just FYI for anyone else fighting this battle. 73, Dave W8FGU ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com -- View this message in context: http://www.nabble.com/Vista-64-USB-drivers-tp16548378p16568608.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] k3 KXV3 Board Missing Pin
Not at all. I had the same question last month. The staff says its suppose to be like that. They are in the process of updating the documentation. John Terry Schieler wrote: I was in the process of installing the KXV3 board in my K3. When plugging the 16 Pin connector on the KXV3 board into J66 on the K3, I noticed that the third pin from the right on the KXV3 connector was missing. The photo appears to clearly show all 16 pins there. Houston, do I have a problem here? Thanks, Terry, WØFM (Please reply direct to MY CALL at arrl.net) ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com -- View this message in context: http://www.nabble.com/k3--KXV3-Board-Missing-Pin-tp15782539p15782614.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KXV3 question
I am currently installing the KXV3 in my K3 (#364). During the installation I noticed the part in the picture on page 11 of the installation guide has all the pins. Mine is missing the 3 pin from the right as you look at the picture. Is this a problem? John Glascock, N0IB -- View this message in context: http://www.nabble.com/KXV3-question-tp15347005p15347005.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com