[Elecraft] Hi Current K2

2009-06-19 Thread richard gilley




 I am embarrassed to say but I have a high current indication on  
 nearly all bands during Tx. (new build and I thought I was being so  
 so careful).

 The Rec. draws 240 ma. at 12.4 volts.  Does change slightly with  
 option changes.

 Attempted transmitter Tune up Test Part Three page 77 has the  
 following results:

 4.045 Mhz   - Hi Cur LCD  to P19
 7.099 Mhz  - Hi Cur LCD  to P19
 10.00 Mhz  - Hi Cur LCD  to P18
 14.060 Mhz  Hi Cur LCD to  P16
 18.090 Mhz   NO  Hi Cur LCD to P.3
 21.054 MHZ  No Hi Cur  LCD to P.8
 25.012 MhzNO Hi Cur  LCD to P.1

 Power set to 2W and 1 W with same indication.

 Current limit set to 2.5A.
 Voltage on C of Q8 and Q7 at 12.4 Vdc.
 Res, measurements page 74 all within limits.

 Changed power supply, when I noticed voltage drop and high current  
 reading of 5 A.  No change with known good supply.

 Hints requested before I tear something.

 Best regards
 Dick AD1G




__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html


Re: [Elecraft] Hi Current K2

2009-06-19 Thread Don Wilhelm
First question is - why are you using 4.045 MHz - that is outside the 
ham band.  Use 3.750 MHz instead.  Similarly, 10.00 MHz should be in the 
range of 10.100 to 10.150 MHz.  Also 25.012 is not a good frequency 
either, use 24.90  That is not likely to change your results with the 
HI-Cur display, but just a comment.

Your receive current draw is about normal - no problem there.

Set CAL CUR to 3.50 amps and try again with the power set to 5 watts.
If the power goes up to a high value (much above 5 watts), there is a 
problem with the power control circuits.

The lack of decent power output on 17 meters and up may be an entirely 
different problem.  Normally Hi-Cur combined with low power output 
indicates a problem in the Low Pass Filter or T4.

Please measure the voltage at the base of Q7 and Q8 during a TUNE.  It 
should be 0.6 to 0.63 volts.

73,
Don W3FPR

richard gilley wrote:

   
 I am embarrassed to say but I have a high current indication on  
 nearly all bands during Tx. (new build and I thought I was being so  
 so careful).

 The Rec. draws 240 ma. at 12.4 volts.  Does change slightly with  
 option changes.

 Attempted transmitter Tune up Test Part Three page 77 has the  
 following results:

 4.045 Mhz   - Hi Cur LCD  to P19
 7.099 Mhz  - Hi Cur LCD  to P19
 10.00 Mhz  - Hi Cur LCD  to P18
 14.060 Mhz  Hi Cur LCD to  P16
 18.090 Mhz   NO  Hi Cur LCD to P.3
 21.054 MHZ  No Hi Cur  LCD to P.8
 25.012 MhzNO Hi Cur  LCD to P.1

 Power set to 2W and 1 W with same indication.

 Current limit set to 2.5A.
 Voltage on C of Q8 and Q7 at 12.4 Vdc.
 Res, measurements page 74 all within limits.

 Changed power supply, when I noticed voltage drop and high current  
 reading of 5 A.  No change with known good supply.

 Hints requested before I tear something.

 Best regards
 Dick AD1G



 

 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 


 No virus found in this incoming message.
 Checked by AVG - www.avg.com 
 Version: 8.5.339 / Virus Database: 270.12.80/2187 - Release Date: 06/19/09 
 06:53:00

   
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html