AW: [Elecraft] Issues after loading 2.34--Gremlins--Need Help!---RESOLVED!
i also have Problems to load firmware I think after build in 2. receiver I have to load firmware several times with loud whistling K3 after reload and switch on and error 'E000202' on the Main display and 'ERR DSE' on the VFO B display. after loading several times I got 2.34 did nothing change to my laptop 73 OE6KYG KX1 244 K2 1331 K3 115 -Ursprüngliche Nachricht- Von: [EMAIL PROTECTED] [mailto:elecraft- [EMAIL PROTECTED] Im Auftrag von David and Dianne on Comcast Gesendet: Montag, 01. September 2008 05:48 An: elecraft@mailman.qth.net Betreff: [Elecraft] Issues after loading 2.34--Gremlins--Need Help!--- RESOLVED! Hi Everyone, The third time was apparently the charm as after my third load of 2.34/1.89 all is apparently in order once again. The cause was unknown but I suspect a communication/port problem problem with the K3 and my Toshiba laptop. The VCO PL1 and PL2 error also seem to be fixed (but fingers crossed on this one though). Many thanks to Lyle, Don, Vic and Ron for the great help and suggestions via e-mail. Amazing support on a Sunday night in the middle of the holiday weekend. I'll be looking for a deep far east DX opening again tomorrow morning 1400Z as was this morning when I worked BX, BT, VR and HS on 20m barefoot SSB with my wire antenna. This is the most difficult DX path here in W1 land. K3 is a real DX-hound. (Forgive my bragging) 73 de N1LQ-Dave ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Issues after loading 2.34--Gremlins--Need Help!
Hi Everyone, I have a 2.34/1.89 firmware loading issue to report. My K3 #371 has been functioning perfectly until this evening. It has the sub-receiver installed which has been working fine as well. Tonight I decided to load 2.34 Beta and did so successfully but after a second attempt. My first attempt resulted in no DSP being loaded in DSP1 but it did load into DSP 2. I got the following error message 'E000202' on the Main display and 'ERR DSE' on the VFO B display. After my successful second attempt load I then got 'ERR PL 1' on the VFO B display when changing bands. It disappeared after a second or two but reappeaed on each band change. Lots of background noise but no signals. I attempted to recalibrate PL1. After the recal. it now displays ERR VCO E 5 and then Er VC4 E00255. I reverted back to 2.23 and now get 'ERR PL 2'. So I again re calibrated the VCO's main and sub and all appears to be ok after several recalibration attempts. But I am back to running 2.23. I'd like to try 2.34 What's happening here? I am at a loss to figure it out. Thanks in advance for any suggestions. I also e-mail K3 support but thought I would post here as it is a holiday weekend. Dave- N1LQ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Issues after loading 2.34--Gremlins--Need Help!
David and Dianne on Comcast wrote: Hi Everyone, I have a 2.34/1.89 firmware loading issue to report. details snipped What's happening here? I don't know, but until Don or Lyle or someone who might actually know appears, you might try this: 1) Set the K3 baudrate to 38400. 2) Select Send All Firmware to K3 in the K3 Utility and resend 2.34 (if you don't have this checkbox, go to View and DE-select Advanced Mode). In case the firmware didn't load completely, this will give you the best chance of getting everything in sync. -- 73, Vic, K2VCO Fresno CA http://www.qsl.net/k2vco ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Issues after loading 2.34--Gremlins--Need Help!
Dave, That sounds like a computer or USB to serial adapter problem rather than a K2 problem. If you can, try again using a computer with a real serial port and let us know the results. In many, many firmware downloads associated with Firmware Field test, I have never experienced a failure - but I am using a real serial port. 73, Don W3FPR David and Dianne on Comcast wrote: Hi Everyone, I have a 2.34/1.89 firmware loading issue to report. My K3 #371 has been functioning perfectly until this evening. It has the sub-receiver installed which has been working fine as well. Tonight I decided to load 2.34 Beta and did so successfully but after a second attempt. My first attempt resulted in no DSP being loaded in DSP1 but it did load into DSP 2. I got the following error message 'E000202' on the Main display and 'ERR DSE' on the VFO B display. After my successful second attempt load I then got 'ERR PL 1' on the VFO B display when changing bands. It disappeared after a second or two but reappeaed on each band change. Lots of background noise but no signals. I attempted to recalibrate PL1. After the recal. it now displays ERR VCO E 5 and then Er VC4 E00255. I reverted back to 2.23 and now get 'ERR PL 2'. So I again re calibrated the VCO's main and sub and all appears to be ok after several recalibration attempts. But I am back to running 2.23. I'd like to try 2.34 What's happening here? I am at a loss to figure it out. Thanks in advance for any suggestions. I also e-mail K3 support but thought I would post here as it is a holiday weekend. Dave- N1LQ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com No virus found in this incoming message. Checked by AVG - http://www.avg.com Version: 8.0.169 / Virus Database: 270.6.14/1643 - Release Date: 8/30/2008 5:18 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Issues after loading 2.34--Gremlins--Need Help!---RESOLVED!
Hi Everyone, The third time was apparently the charm as after my third load of 2.34/1.89 all is apparently in order once again. The cause was unknown but I suspect a communication/port problem problem with the K3 and my Toshiba laptop. The VCO PL1 and PL2 error also seem to be fixed (but fingers crossed on this one though). Many thanks to Lyle, Don, Vic and Ron for the great help and suggestions via e-mail. Amazing support on a Sunday night in the middle of the holiday weekend. I'll be looking for a deep far east DX opening again tomorrow morning 1400Z as was this morning when I worked BX, BT, VR and HS on 20m barefoot SSB with my wire antenna. This is the most difficult DX path here in W1 land. K3 is a real DX-hound. (Forgive my bragging) 73 de N1LQ-Dave ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com