Hi George
I am keying the AL=811 from the key jack on the adaptor via the CAT-6
cable.
I also reinstalled the beta f/w files, for the KXPA, and it just
occurred to me to reintall the config file for the KX3.
I will do that after breakfast.
73, Al ve7ear
On 09/02/2014 10:02 PM, george fritkin wrote:
Are you keying the al811h with the key jack on the kxpa100? That won't work
George W6GF
--
On Sun, Feb 9, 2014 8:58 PM PST Al Sather wrote:
Greetings All
I am having a problem with my KXPA100 driving my AL-811H.
First what works
KX3 driving AL-811H no problems, and at 10 watts drive I get over 125 watts
out, about what I expect.
KX3 driving KXPA100 no problems, and performs as advertised, and tested to 90
watts.
KX3 using my KXPA100 to drive AL-811H which has out put pretty much as expected
(approx less that 40 watts in with more than 400 out)
It should be noted my all f/w etc. is up to date, and today I replaced the
power amp drivers with the most recent beta version. This did not help, as
expected. Also, the ATU in both the KX3 and KXPA are bypassed, since there is a
third antenna tuner in line to handle the high power from the AL-811.
Now the problem! My Rx was attenuated from a S7-S8 signal to a S1-S2 while
working the Elecraft SSB net this morning when the AL-811 is keyed, even
briefly (i.e just a dit).
Turning the 811H off and on or going from opr to stand by restores the Rx
to normal. While talking with the net, I was Txing nearly 500 watts, but needed to go from
opr-stand by, to copy net control. Tx was not affected.
I have carefully followed the suggested wiring by the KXPA100 user manual as
shown on page 14. If I use the Key line found on the KXPA100, I still get
attention of the Rx upon termination of Tx.
Up until today, the KXPA100 has performed flawlessly and a joy to assemble and
to operate.
My question is, ``Where may the fault lie``.
Changing the ``Opr`` status resets the attention in the AL-811H. Suggests an
AL-811 issue.
But, only when the KXPA is part of the circuit, Rx attenuation occurs. Suggests
and KXPA issue.
Or, these two amps just do not each other ;-(
If I set the power level, say to 2 watts, the KXPA should not fire as a PA, but
it is still part of the circuit, and Rx attenuation occurs. Could there be a
grounding isssue.
The KX3 is able to drive the AL-811 without issue.
Any suggestions as to what I can do next, or where should I look for an issue.
Thank you
Al, ve7ear
apsat...@shaw.ca
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
-
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4259 / Virus Database: 3697/7079 - Release Date: 02/09/14
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html