Re: [Elecraft] K3 - ERR DSE DD0VS
Hi Harald; Always post your serial #, it really helps narrow down problems. If older, the 28pin and 5 pin headers on the RF board going to the front panel were tin and get oxidized. Change them to gold. To confirm this is the problem; remove the two bottom bolts for the FP, pry gently in the two slots to move the FP out on the pins a small bit then shove the FP back on. That will temporarily clear poor connections. Also search at the groups.io page https://groups.io/g/Elecraft-K3/topics Keith WE6R Elecraft K3/K4 Tech __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 - ERR DSE
Hello YLs and Oms, I am still struggling with my K3 and the ERR DSE. In rare cases I can switch on K3 completely and it runs stable. That let me assume, that the startup of µC, e.g. DSP, is not working correctly. Do you have any further hints to find out where the issue is located? Vy73 Harald DD0VS __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 ERR DSE / E 000202 DD0VS
Harald; What is the serial # of the K3? If older, did you change the P30 and P35 front panel pins (to RF board) to gold?. If you have a sub receiver, make sure it is enabled and then check FW revisions, if the AUX DSP board has mismatched FW, you can get ERR DSE. Keith WE6R Elecraft K3/K4 Tech __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 ERR DSE / E 000202
Dear All, the issue seems to be intermittent, simple disassembly/assembly of DSP-board did not help, but switch on/off sometimes "awakes" DSP. Seems to be no real defect but weak contact or cold solder joint. Any idea where to search more in detail? Vy73 Harald DD0VS Von: Harald Fritzsche Gesendet: Sonntag, 19. Februar 2023 14:27 An: 'elecraft@mailman.qth.net' Betreff: K3 ERR DSE / E 000202 Dear All, My K3 is prompting now with ERR DSE, during CQ WPX RTTY it was ok, next switch on this week end it prompts this error. Reloading DSP-firmware wasn't successful. Would be open for further suggestions, my time is limited to some hours on week end, so if you send me suggestion, please understand that I can react only with delay. TNX Vy73 Harald DD0VS __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 ERR DSE / E 000202
Dear All, My K3 is prompting now with ERR DSE, during CQ WPX RTTY it was ok, next switch on this week end it prompts this error. Reloading DSP-firmware wasn't successful. Would be open for further suggestions, my time is limited to some hours on week end, so if you send me suggestion, please understand that I can react only with delay. TNX Vy73 Harald DD0VS __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 ERR DSE
To don and all others, I didnt even have to call or mail K3support but I have the response already. I have reloaded the firmware now on MC 5.56 the DSP is the same but got reloaded anyway. The problem would seem to be overwork of the CPU and this seems to fit with my recollection that it only seems to occur when I have the pc connected. The response from Gary was:- * That error can occur if there are a lot of things going on at the same time, such as CAT control is being used with a computer and NR or NB are enabled. It is a report of excessive traffic to/from the K3 MCU. Try turning things off that are not absolutely necessary, and/or reduce the polling interval between the PC and the K3. * My thanks to all who replied especially K3support i.e. Eric for forwarding the mail and Gary and Don for there appropriate responses. 73 de Tony G6GLP On 18/01/2017 00:54, Don Wilhelm wrote: Tony, ERR DSE says that there was a missing echo from a DSP command - see page 68 in the K3 manual. The first level of "fix" is to reload the DSP1 (and DSP2 firmware if applicable). If the problem continues, yes, contact K3support for further assistance. 73, Don W3FPR On 1/17/2017 2:22 PM, Tony G6GLP wrote: Hi All, Some weeks ago now I installed the 5.54 MCU beta to use with the K-POD I have not had any problems until the last couple of days when I intermittently get a ERR DSE E 04004C. What does the E 04004C mean? Factual answers please or do I have to contact K3support? - No virus found in this message. Checked by AVG - www.avg.com Version: 2016.0.7996 / Virus Database: 4749/13789 - Release Date: 01/17/17 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 ERR DSE
Tony, ERR DSE says that there was a missing echo from a DSP command - see page 68 in the K3 manual. The first level of "fix" is to reload the DSP1 (and DSP2 firmware if applicable). If the problem continues, yes, contact K3support for further assistance. 73, Don W3FPR On 1/17/2017 2:22 PM, Tony G6GLP wrote: Hi All, Some weeks ago now I installed the 5.54 MCU beta to use with the K-POD I have not had any problems until the last couple of days when I intermittently get a ERR DSE E 04004C. What does the E 04004C mean? Factual answers please or do I have to contact K3support? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 ERR DSE
Hi All, Some weeks ago now I installed the 5.54 MCU beta to use with the K-POD I have not had any problems until the last couple of days when I intermittently get a ERR DSE E 04004C. Switching off and restarting the K3 with the power switch clears the fault and then the K3 works perfectly normally. There are several questions I would like answers to if anyone has any ideas. Is there a known cause to this problem? Is there a fix if it is known even if its on the todo list. Is this the sign of a problem starting? What does the E 04004C mean? Factual answers please or do I have to contact K3support? 73 de Tony G6GLP __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] k3 ERR DSE
On 2/10/2015 9:27 PM, John McBee wrote: I was getting this error from the kxr3 menu when changing from ATU port to BNC port I have gotten this error a few times since I have installed the kxr3. But all usually works. The book said to try to reload the dsp 1 firmware and dsp2 firmware, so I opened up the k3 utility and tried to reload all firmware. The k3 errored out on loading firmware and display said MCU LD and lost com port communications. I could not turn off k3 by pwr button so turned off pwr supply, now can't get the rig to reset buy holding the shift-lo button in while pwr up k3. So can't load new firmware yet. Any suggestions.. I will keep looking in manual for a reset option. Thanks John __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to jrmc...@cox.net I have read the MCU load error under K3 Firmware Self-Test and what to do in an error of loading MCU but I have lost communications with the k3 with my serial to usb cable that I normally use and have tried a serial to serial cable to another computer that still has a serial port- DB9 connections, I have also changed the baud rate to 38400 which it was before it crashed. No luck with any of these actions. Any help would be great. John __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] k3 ERR DSE
I was getting this error from the kxr3 menu when changing from ATU port to BNC port I have gotten this error a few times since I have installed the kxr3. But all usually works. The book said to try to reload the dsp 1 firmware and dsp2 firmware, so I opened up the k3 utility and tried to reload all firmware. The k3 errored out on loading firmware and display said MCU LD and lost com port communications. I could not turn off k3 by pwr button so turned off pwr supply, now can't get the rig to reset buy holding the shift-lo button in while pwr up k3. So can't load new firmware yet. Any suggestions.. I will keep looking in manual for a reset option. Thanks John __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] [K3] ERR DSE message
I have suddenly started to get an intermittent ERR DSE message on my K3 - the main display shows E0401E2. It occurs about once a day on average I guess. I have reloaded the DSP firmware as recommended but it has not cured this problem. I recently added a P3 with P3SVGA - it is all working fine. The power for the P3 is not taken from the K3. However the error has only started since the P3 was added, so I suspect something to do with this. The obvious change to the K3 is a change from 9,600 Bd to 38,400 for the P3. The PC, SteppIR controller and SPE 1K-FA all run at 9,600 and connect to the P3 PC connector. It all seems ok. Has anyone else seen this? I would appreciate any help. However I will not be able to try any fixes for a couple of weeks as I am away, but will be watching the reflector for any suggestions. 73 Phil Holliday ZL3PAH __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] k3 err dse/kdvr3
i tried un-installing the kdvr3 and put all back together without it in and still got this message, and also tried installing it again and still same message... i am thinking the dsp board went bye bye on me for some reason.. any other ideas i am open to all... _ Windows Live™: Keep your life in sync. http://windowslive.com/explore?ocid=TXT_TAGLM_BR_life_in_synch_052009 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] k3 err dse
Don, I had a similar problem when installing the k3DVR. Nothing tried made any sense. So I de-installed the DVR and re-installed it and it worked! Good luck, Fred, AE6IC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] k3 err dse
i just installed the k3dvr and now i am getting an error message of ERR DSE. in the manuel it suggest to reload the dsp which i have tried to do but with no luck it says the " DSP1 VERIFICATION FALIED. RELOAD DSP1." i have tried this several times with the same results.. any ideas on what this could be? i even tried spliting the front panel again thinking that the pins were not lined up but they were and everything is in oreder as i can tell. thanks don wa1bxy _ Hotmail® has a new way to see what's up with your friends. http://windowslive.com/Tutorial/Hotmail/WhatsNew?ocid=TXT_TAGLM_WL_HM_Tutorial_WhatsNew1_052009 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html