RE: [Elecraft] Component ID

2006-11-15 Thread Darwin, Keith
Hmmm, I did a quick Google search on 25LC320.  It said it was an serial
SPI bus EEPROM.

Talk about knock me over.  I'm in the middle of configuring software to
talk to ... a SPI bus EEPROM.

If google is right, then the LM380N and 25LC320 are NOT the same thing
...

- Keith whatdoiknowi'mjustasoftwareguy N1AS - 

-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED]
Sent: Wednesday, November 15, 2006 11:44 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] Component ID

HI

I am inventorying my k2 kit and have a question.
On the control board I should have a LM380N-8 audio amp.
I don't have that, but do have a 25LC320/1fv0526.
They are probably the same, but would rather be sure than sorry!
Thanks
Scott N5SM

___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com


Re: [Elecraft] Component ID

2006-11-15 Thread Marshall Jose

Scott,

On the control board, U9 is the LM380 which you should have, and U7 is 
the 25LC320 serial EEPROM which you ALSO should have. So it sounds like 
you might be missing the LM380, eh?


Well, based on my experience, you should go through everything again 
with a stronger source of illumination before calling Elecraft to ask to 
have a missing part replaced. :)


Good luck!

[EMAIL PROTECTED] wrote:


HI

I am inventorying my k2 kit and have a question.
On the control board I should have a LM380N-8 audio amp.
I don't have that, but do have a 25LC320/1fv0526.
They are probably the same, but would rather be sure than
sorry!
Thanks
Scott N5SM


--

Marshall Jose, WA3VPZ


___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft


Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com


RE: [Elecraft] Component ID

2006-11-15 Thread Don Wilhelm
Scott,

You will need the 25LC320 for the U7 slot - an LM380N-8 must go into U9.
Check all the 8 pin devices on the black foam again - Christine rarely makes
a packing mistake.

73,
Don W3FPR

 -Original Message-

 I am inventorying my k2 kit and have a question.
 On the control board I should have a LM380N-8 audio amp.
 I don't have that, but do have a 25LC320/1fv0526.
 They are probably the same, but would rather be sure than
 sorry!
 Thanks
 Scott N5SM


___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com


Re: [Elecraft] Component ID

2006-11-15 Thread Joseph Reed
Don,

Your advice to re-inventory is correct.  But Christine has been known to have 
had a bad day.  In my last K2 (K2, KSB2, KIO2, KNB2, K60XV,K160RX, KAF2, KAT2, 
KBT2, EC2, KPA100, KAT100) I have been short shipped THREE (3) parts.

As the late Carl Sagen would say, Billions and billions of parts.  It sure 
seemed that way.  Whew we are talking five nines plus!

That is phenominal.  Eric and Wayne need to add a web page to show us who some 
of the people who make the magic/mojo happen.

But you bet check the foam, both sides.  Even Vegas wouldn't bet, much less put 
a line on Christine.  

Joe N9JR

- Original Message 
From: Don Wilhelm [EMAIL PROTECTED]
To: [EMAIL PROTECTED]; elecraft@mailman.qth.net
Sent: Wednesday, November 15, 2006 11:40:43 AM
Subject: RE: [Elecraft] Component ID


Scott,

You will need the 25LC320 for the U7 slot - an LM380N-8 must go into U9.
Check all the 8 pin devices on the black foam again - Christine rarely makes
a packing mistake.

73,
Don W3FPR
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com