Re: [Elecraft] [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements
Loaded 3.59 just now. Radio NZ on 9765, locks on with the K3 at 9764.984, it's dithering a couple of hz. 5-4-5-4-3 etc. After this load I thought I had a problem. It ended the download and returned the K3 to (what I thought) would be normal operation with a loud pop and crackle in the speaker. The S-meter was pegged out. I shut down the K3 for a few seconds and turned it back on with the same results. So I turned off the K3 and the power supply for a little longer then turned it back on, meter still pegged out, after several seconds or perhaps a minute the meter slowly came back down and I was receiving Radio NZ. Now everything seems to be ok. I have not tried transmitting yet. Dale, K9VUJ On 18, Nov 2009, at 20:41, Wayne Burdick wrote: K3 beta-test firmware revision 3.59 (with DSP rev. 2.46) is now available. See release notes below. Rev. 3.59 does _not_ include any changes to DVR message playback and cancel. These are still in the works and will be made available in time for the phone contest this weekend. Please send any questions to k3supp...@elecraft.com. For instructions on how to load beta firmware, see: http://www.elecraft.com/K3/k3_software.htm 73, Wayne N6KR * * * MCU 3.59 / DSP 2.46, 11-18-2009 * FSK-D WAS CHANGING TO AFSK-A ON A/B or REV: Fixed. * SYNC AM VFO TRACKING ACCURACY IMPROVED (DSP 2.46). The offset contributed by the synchronous AM detector's PLL should be only a few Hz, max. * SWR INDICATOR TONES AFTER ATU TUNE: If switch tones are enabled, a second tone will be emitted following an ATU TUNE. This tone provides a rough idea of the SWR that the KAT3 was able to obtain: Lower pitch than 1st tone: Unknown SWR (ant. may be shorted) Same pitch as 1st tone: SWR = 2.0:1 Medium-high pitch: SWR = 3.0:1 High pitch: SWR 3.0:1. This feature was added primarily for our blind customers, but it’s useful whenever you tap ATU TUNE without looking at the final SWR reading. Remote Control Command Changes: * IC COMMAND (ICON status): Now returning correct message bank in voice modes (byte a, bit 3). Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/Elecraft_K3/ * Your email settings: Individual Email | Traditional * To change settings online go to: http://groups.yahoo.com/group/Elecraft_K3/join (Yahoo! ID required) * To change settings via email: elecraft_k3-dig...@yahoogroups.com elecraft_k3-fullfeatu...@yahoogroups.com * To unsubscribe from this group, send an email to: elecraft_k3-unsubscr...@yahoogroups.com * Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements
FWIW... In rev-3.57 my K3 was typically locking 5-6 Hz above the zero beat carrier. That seems to have been cut in half with this revision, now locking 2-3 Hz above carrier. All India Radio carrier at 9869.986 KHz locks in AM Sync at .988-.989. (All India Radio transmitters seem to be consistently about 15 Hz low.) When I was a kid I dreamed of having a SW receiver that was accurate to within 5 KHz, heheh Didn't have any problems with loading the F/W. 73, Drew AF2Z Some SWBC stations can be pretty far off freq. All India Radio is consistently about 10 or 12 Hz low. On Thu, 19 Nov 2009 03:46:31 -0600, you wrote: Loaded 3.59 just now. Radio NZ on 9765, locks on with the K3 at 9764.984, it's dithering a couple of hz. 5-4-5-4-3 etc. After this load I thought I had a problem. It ended the download and returned the K3 to (what I thought) would be normal operation with a loud pop and crackle in the speaker. The S-meter was pegged out. I shut down the K3 for a few seconds and turned it back on with the same results. So I turned off the K3 and the power supply for a little longer then turned it back on, meter still pegged out, after several seconds or perhaps a minute the meter slowly came back down and I was receiving Radio NZ. Now everything seems to be ok. I have not tried transmitting yet. Dale, K9VUJ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements
I had the same loud pop and crackle with s-meter pegging out when I turned on power to the K3 today. It was previously set on Radio NZ freq and AM sync was enabled when I turned it off this morning before leaving on a road trip. I re-loaded 3.59 late this afternoon and now all seems to be ok. I tried turning off the K3, leaving it on AM with sync enabled and it did not pop and crack plus the S-meter did not peg out. I must have had a faulty upload the first time. I have to admit while uploading the firmware I was doing other things on the computer so maybe it was due to my fiddling. I'll check it out again early in the morning, but everything seems to be ok now. In fact it appears the sync is locking faster and more steady now. Keeping fingers crossed. Dale, K9VUJ On 19, Nov 2009, at 3:46, dalej wrote: Loaded 3.59 just now. Radio NZ on 9765, locks on with the K3 at 9764.984, it's dithering a couple of hz. 5-4-5-4-3 etc. After this load I thought I had a problem. It ended the download and returned the K3 to (what I thought) would be normal operation with a loud pop and crackle in the speaker. The S-meter was pegged out. I shut down the K3 for a few seconds and turned it back on with the same results. So I turned off the K3 and the power supply for a little longer then turned it back on, meter still pegged out, after several seconds or perhaps a minute the meter slowly came back down and I was receiving Radio NZ. Now everything seems to be ok. I have not tried transmitting yet. Dale, K9VUJ On 18, Nov 2009, at 20:41, Wayne Burdick wrote: K3 beta-test firmware revision 3.59 (with DSP rev. 2.46) is now available. See release notes below. Rev. 3.59 does _not_ include any changes to DVR message playback and cancel. These are still in the works and will be made available in time for the phone contest this weekend. Please send any questions to k3supp...@elecraft.com. For instructions on how to load beta firmware, see: http://www.elecraft.com/K3/k3_software.htm 73, Wayne N6KR * * * MCU 3.59 / DSP 2.46, 11-18-2009 * FSK-D WAS CHANGING TO AFSK-A ON A/B or REV: Fixed. * SYNC AM VFO TRACKING ACCURACY IMPROVED (DSP 2.46). The offset contributed by the synchronous AM detector's PLL should be only a few Hz, max. * SWR INDICATOR TONES AFTER ATU TUNE: If switch tones are enabled, a second tone will be emitted following an ATU TUNE. This tone provides a rough idea of the SWR that the KAT3 was able to obtain: Lower pitch than 1st tone: Unknown SWR (ant. may be shorted) Same pitch as 1st tone: SWR = 2.0:1 Medium-high pitch: SWR = 3.0:1 High pitch: SWR 3.0:1. This feature was added primarily for our blind customers, but it’s useful whenever you tap ATU TUNE without looking at the final SWR reading. Remote Control Command Changes: * IC COMMAND (ICON status): Now returning correct message bank in voice modes (byte a, bit 3). Yahoo! Groups Links Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/Elecraft_K3/ * Your email settings: Individual Email | Traditional * To change settings online go to: http://groups.yahoo.com/group/Elecraft_K3/join (Yahoo! ID required) * To change settings via email: elecraft_k3-dig...@yahoogroups.com elecraft_k3-fullfeatu...@yahoogroups.com * To unsubscribe from this group, send an email to: elecraft_k3-unsubscr...@yahoogroups.com * Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements
During firmware uploads, I don't even touch the mouse! May be safer to just leave the room. Steve N4LQ n...@carolina.rr.com - Original Message - From: dalej dal...@mac.com To: elecraft...@yahoogroups.com Cc: Elecraft Reflector elecraft@mailman.qth.net Sent: Thursday, November 19, 2009 7:13 PM Subject: Re: [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements I had the same loud pop and crackle with s-meter pegging out when I turned on power to the K3 today. It was previously set on Radio NZ freq and AM sync was enabled when I turned it off this morning before leaving on a road trip. I re-loaded 3.59 late this afternoon and now all seems to be ok. I tried turning off the K3, leaving it on AM with sync enabled and it did not pop and crack plus the S-meter did not peg out. I must have had a faulty upload the first time. I have to admit while uploading the firmware I was doing other things on the computer so maybe it was due to my fiddling. I'll check it out again early in the morning, but everything seems to be ok now. In fact it appears the sync is locking faster and more steady now. Keeping fingers crossed. Dale, K9VUJ On 19, Nov 2009, at 3:46, dalej wrote: Loaded 3.59 just now. Radio NZ on 9765, locks on with the K3 at 9764.984, it's dithering a couple of hz. 5-4-5-4-3 etc. After this load I thought I had a problem. It ended the download and returned the K3 to (what I thought) would be normal operation with a loud pop and crackle in the speaker. The S-meter was pegged out. I shut down the K3 for a few seconds and turned it back on with the same results. So I turned off the K3 and the power supply for a little longer then turned it back on, meter still pegged out, after several seconds or perhaps a minute the meter slowly came back down and I was receiving Radio NZ. Now everything seems to be ok. I have not tried transmitting yet. Dale, K9VUJ On 18, Nov 2009, at 20:41, Wayne Burdick wrote: K3 beta-test firmware revision 3.59 (with DSP rev. 2.46) is now available. See release notes below. Rev. 3.59 does _not_ include any changes to DVR message playback and cancel. These are still in the works and will be made available in time for the phone contest this weekend. Please send any questions to k3supp...@elecraft.com. For instructions on how to load beta firmware, see: http://www.elecraft.com/K3/k3_software.htm 73, Wayne N6KR * * * MCU 3.59 / DSP 2.46, 11-18-2009 * FSK-D WAS CHANGING TO AFSK-A ON A/B or REV: Fixed. * SYNC AM VFO TRACKING ACCURACY IMPROVED (DSP 2.46). The offset contributed by the synchronous AM detector's PLL should be only a few Hz, max. * SWR INDICATOR TONES AFTER ATU TUNE: If switch tones are enabled, a second tone will be emitted following an ATU TUNE. This tone provides a rough idea of the SWR that the KAT3 was able to obtain: Lower pitch than 1st tone: Unknown SWR (ant. may be shorted) Same pitch as 1st tone: SWR = 2.0:1 Medium-high pitch: SWR = 3.0:1 High pitch: SWR 3.0:1. This feature was added primarily for our blind customers, but it’s useful whenever you tap ATU TUNE without looking at the final SWR reading. Remote Control Command Changes: * IC COMMAND (ICON status): Now returning correct message bank in voice modes (byte a, bit 3). Yahoo! Groups Links Yahoo! Groups Links Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/Elecraft_K3/ * Your email settings: Individual Email | Traditional * To change settings online go to: http://groups.yahoo.com/group/Elecraft_K3/join (Yahoo! ID required) * To change settings via email: elecraft_k3-dig...@yahoogroups.com elecraft_k3-fullfeatu...@yahoogroups.com * To unsubscribe from this group, send an email to: elecraft_k3-unsubscr...@yahoogroups.com * Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/ No virus found in this incoming message. Checked by AVG - www.avg.com Version: 9.0.707 / Virus Database: 270.14.73/2514 - Release Date: 11/19/09 14:42:00 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements
Or just install Linux ;) On Thu, 2009-11-19 at 20:24 -0500, Steve Ellington wrote: During firmware uploads, I don't even touch the mouse! May be safer to just leave the room. Steve N4LQ n...@carolina.rr.com - Original Message - From: dalej dal...@mac.com To: elecraft...@yahoogroups.com Cc: Elecraft Reflector elecraft@mailman.qth.net Sent: Thursday, November 19, 2009 7:13 PM Subject: Re: [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements I had the same loud pop and crackle with s-meter pegging out when I turned on power to the K3 today. It was previously set on Radio NZ freq and AM sync was enabled when I turned it off this morning before leaving on a road trip. I re-loaded 3.59 late this afternoon and now all seems to be ok. I tried turning off the K3, leaving it on AM with sync enabled and it did not pop and crack plus the S-meter did not peg out. I must have had a faulty upload the first time. I have to admit while uploading the firmware I was doing other things on the computer so maybe it was due to my fiddling. I'll check it out again early in the morning, but everything seems to be ok now. In fact it appears the sync is locking faster and more steady now. Keeping fingers crossed. Dale, K9VUJ On 19, Nov 2009, at 3:46, dalej wrote: Loaded 3.59 just now. Radio NZ on 9765, locks on with the K3 at 9764.984, it's dithering a couple of hz. 5-4-5-4-3 etc. After this load I thought I had a problem. It ended the download and returned the K3 to (what I thought) would be normal operation with a loud pop and crackle in the speaker. The S-meter was pegged out. I shut down the K3 for a few seconds and turned it back on with the same results. So I turned off the K3 and the power supply for a little longer then turned it back on, meter still pegged out, after several seconds or perhaps a minute the meter slowly came back down and I was receiving Radio NZ. Now everything seems to be ok. I have not tried transmitting yet. Dale, K9VUJ On 18, Nov 2009, at 20:41, Wayne Burdick wrote: K3 beta-test firmware revision 3.59 (with DSP rev. 2.46) is now available. See release notes below. Rev. 3.59 does _not_ include any changes to DVR message playback and cancel. These are still in the works and will be made available in time for the phone contest this weekend. Please send any questions to k3supp...@elecraft.com. For instructions on how to load beta firmware, see: http://www.elecraft.com/K3/k3_software.htm 73, Wayne N6KR * * * MCU 3.59 / DSP 2.46, 11-18-2009 * FSK-D WAS CHANGING TO AFSK-A ON A/B or REV: Fixed. * SYNC AM VFO TRACKING ACCURACY IMPROVED (DSP 2.46). The offset contributed by the synchronous AM detector's PLL should be only a few Hz, max. * SWR INDICATOR TONES AFTER ATU TUNE: If switch tones are enabled, a second tone will be emitted following an ATU TUNE. This tone provides a rough idea of the SWR that the KAT3 was able to obtain: Lower pitch than 1st tone: Unknown SWR (ant. may be shorted) Same pitch as 1st tone: SWR = 2.0:1 Medium-high pitch: SWR = 3.0:1 High pitch: SWR 3.0:1. This feature was added primarily for our blind customers, but it’s useful whenever you tap ATU TUNE without looking at the final SWR reading. Remote Control Command Changes: * IC COMMAND (ICON status): Now returning correct message bank in voice modes (byte a, bit 3). Yahoo! Groups Links Yahoo! Groups Links Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/Elecraft_K3/ * Your email settings: Individual Email | Traditional * To change settings online go to: http://groups.yahoo.com/group/Elecraft_K3/join (Yahoo! ID required) * To change settings via email: elecraft_k3-dig...@yahoogroups.com elecraft_k3-fullfeatu...@yahoogroups.com * To unsubscribe from this group, send an email to: elecraft_k3-unsubscr...@yahoogroups.com * Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/ No virus found in this incoming message. Checked by AVG - www.avg.com Version: 9.0.707 / Virus Database: 270.14.73/2514 - Release Date: 11/19/09 14:42:00 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home:
Re: [Elecraft] [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements
Yesterday night, I upgraded to 3.59, I don't know why, but upload speed is very very slow. Fortunately, firmware works just fine. All the best! David,ba4rf __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements
Leaving the room is good :) On Thu, Nov 19, 2009 at 8:24 PM, Steve Ellington n...@carolina.rr.com wrote: During firmware uploads, I don't even touch the mouse! May be safer to just leave the room. Steve N4LQ n...@carolina.rr.com - Original Message - From: dalej dal...@mac.com To: elecraft...@yahoogroups.com Cc: Elecraft Reflector elecraft@mailman.qth.net Sent: Thursday, November 19, 2009 7:13 PM Subject: Re: [Elecraft_K3] K3 Beta Firmware Rev. 3.59: Misc. improvements I had the same loud pop and crackle with s-meter pegging out when I turned on power to the K3 today. It was previously set on Radio NZ freq and AM sync was enabled when I turned it off this morning before leaving on a road trip. I re-loaded 3.59 late this afternoon and now all seems to be ok. I tried turning off the K3, leaving it on AM with sync enabled and it did not pop and crack plus the S-meter did not peg out. I must have had a faulty upload the first time. I have to admit while uploading the firmware I was doing other things on the computer so maybe it was due to my fiddling. I'll check it out again early in the morning, but everything seems to be ok now. In fact it appears the sync is locking faster and more steady now. Keeping fingers crossed. Dale, K9VUJ On 19, Nov 2009, at 3:46, dalej wrote: Loaded 3.59 just now. Radio NZ on 9765, locks on with the K3 at 9764.984, it's dithering a couple of hz. 5-4-5-4-3 etc. After this load I thought I had a problem. It ended the download and returned the K3 to (what I thought) would be normal operation with a loud pop and crackle in the speaker. The S-meter was pegged out. I shut down the K3 for a few seconds and turned it back on with the same results. So I turned off the K3 and the power supply for a little longer then turned it back on, meter still pegged out, after several seconds or perhaps a minute the meter slowly came back down and I was receiving Radio NZ. Now everything seems to be ok. I have not tried transmitting yet. Dale, K9VUJ On 18, Nov 2009, at 20:41, Wayne Burdick wrote: K3 beta-test firmware revision 3.59 (with DSP rev. 2.46) is now available. See release notes below. Rev. 3.59 does _not_ include any changes to DVR message playback and cancel. These are still in the works and will be made available in time for the phone contest this weekend. Please send any questions to k3supp...@elecraft.com. For instructions on how to load beta firmware, see: http://www.elecraft.com/K3/k3_software.htm 73, Wayne N6KR * * * MCU 3.59 / DSP 2.46, 11-18-2009 * FSK-D WAS CHANGING TO AFSK-A ON A/B or REV: Fixed. * SYNC AM VFO TRACKING ACCURACY IMPROVED (DSP 2.46). The offset contributed by the synchronous AM detector's PLL should be only a few Hz, max. * SWR INDICATOR TONES AFTER ATU TUNE: If switch tones are enabled, a second tone will be emitted following an ATU TUNE. This tone provides a rough idea of the SWR that the KAT3 was able to obtain: Lower pitch than 1st tone: Unknown SWR (ant. may be shorted) Same pitch as 1st tone: SWR = 2.0:1 Medium-high pitch: SWR = 3.0:1 High pitch: SWR 3.0:1. This feature was added primarily for our blind customers, but it’s useful whenever you tap ATU TUNE without looking at the final SWR reading. Remote Control Command Changes: * IC COMMAND (ICON status): Now returning correct message bank in voice modes (byte a, bit 3). Yahoo! Groups Links Yahoo! Groups Links Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/Elecraft_K3/ * Your email settings: Individual Email | Traditional * To change settings online go to: http://groups.yahoo.com/group/Elecraft_K3/join (Yahoo! ID required) * To change settings via email: elecraft_k3-dig...@yahoogroups.com elecraft_k3-fullfeatu...@yahoogroups.com * To unsubscribe from this group, send an email to: elecraft_k3-unsubscr...@yahoogroups.com * Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/ No virus found in this incoming message. Checked by AVG - www.avg.com Version: 9.0.707 / Virus Database: 270.14.73/2514 - Release Date: 11/19/09 14:42:00 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:
