Re: [Elecraft] Firmware, K3, large jump AB3JN
Ok i have two transverse that I put together a 144 MHz and a 50 MHz the 144 I finished think 2009 did the cals but if I remember correctly when I tried testing it when I keyed up it was like I got a carrier or something I had a hand held in the shack and I could here it key but did not get any audio. The six meter my father in law started and he passed so we picked it all up and put it in a box. And i recently finished it but have not got to do the calibration procedures or test it yet. Sent from my Verizon, Samsung Galaxy smartphone From: Keith Trinity WE6R Sent: Monday, June 15, 2020 3:50:21 PM To: Joseph McIntire ; elecraft@mailman.qth.net ; supp...@elecraft.com Subject: Re: [Elecraft] Firmware, K3, large jump AB3JN You must go into the config menu, set KPA3 to "nor" then cycle power. Then connect to the utility and the 50w should be available to run from there. Set KXV3 to nor also, cycle power, then you can use the Utility to run the MW test too. Looks like you DID do the 50 manually and the TXGN number most likely changed, (see next sentence). (The MW and 5w need to be run too). You can do all the gain cals manually but the Utility is soo much easier. Manually you make sure TUN PWR is nor, then set power to 50w EXACTLY, (or 5w for the low cal), then long press XMIT and let it send a carrier for several seconds. You will see the TXGN number change from the default 10 to something (although 10 is a valid number too, just the default and should not be 10 on all bands). For MW, set KXV3 to "test" and set to 1.0mw exactly and TUNE for several seconds) DON'T FORGET TO TAKE IT OUT OF TEST, HI HI, there is NO indication and it will confound you, been there, ha ha. Then Never, ever, EVER set your tx power to *exactly* 5watts, 50watts or 1.0MW ever again because you can inadvertently re-do the tx gain cal and if not into a flat dummy load, you can get it all fouled up. Keith WE6R, Elecraft K3 Tech. On 6/15/2020 1:33 PM, Joseph McIntire wrote: Ok will do. Question though. It is calling it the high power or 50 watt TX gain calibration. Turn off the ATU if you have one. I don't wish I did. But anyway select each band go to tune and verify 50 watts out. Ok I had 50 watts on each. But have not seen in the manual where you would adjust anything if it wasn't. To me thT verifing not calibrating. I also seen on the K3 utility under the calibration tab there is a button for that but it was grayed out and couldn't be selected. How does it work. I have not seen any instructions for doing it that way. Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone From: Keith Trinity WE6R <mailto:ke...@elecraft.com> Sent: Monday, June 15, 2020 2:30:06 PM To: Joseph McIntire <mailto:ki4...@msn.com>; elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net> <mailto:elecraft@mailman.qth.net>; supp...@elecraft.com<mailto:supp...@elecraft.com> <mailto:supp...@elecraft.com> Subject: Re: [Elecraft] Firmware, K3, large jump AB3JN Also we suggest setting the K3 Utility to the ADVANCED mode for more control. Keith WE6R On 6/15/2020 12:27 PM, Joseph McIntire wrote: Ok wel will do that. I do not have the sub receiver so that makes it a little easier. I still have all the original paper work and manuals. I was going to print the latest manuals tonight. I know that there's options in there I don't have but most the functions updated by firmware should be in there. Thank you for your assistance Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone From: Keith Trinity WE6R <mailto:ke...@elecraft.com> Sent: Monday, June 15, 2020 2:19:54 PM To: Joseph McIntire <mailto:ki4...@msn.com>; elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net> <mailto:elecraft@mailman.qth.net>; supp...@elecraft.com<mailto:supp...@elecraft.com> <mailto:supp...@elecraft.com> Subject: Re: [Elecraft] Firmware, K3, large jump AB3JN At this point, I would do the reset, then set RS232 to 38400 to continue on with the DSP load. (reset puts it at 4800 which is SLOW). Then Reset again after FP & DSP have loaded, if you have a sub, you will have to turn it on in config menu, then cycle power, then load DSP2. Then a reset again after all FW is loaded. Then you will have to setup filters, options and do the TX gain cal. The K3 kit build manual has all of that. It will give you confidence you have a clean start. Let us know ... Don't forget to do a new configuration save when it is all setup!! (should you ever have to "go back"). Keith WE6R Elecraft Tech. On 6/15/2020 12:07 PM, Joseph McIntire wrote: Yes that is what happened I just loaded the latest FW the mcu and FPF firmware update went well but when it loaded the DSP when it restarted the radio
Re: [Elecraft] Firmware, K3, large jump AB3JN
You must go into the config menu, set KPA3 to "nor" then cycle power. Then connect to the utility and the 50w should be available to run from there. Set KXV3 to nor also, cycle power, then you can use the Utility to run the MW test too. Looks like you DID do the 50 manually and the TXGN number most likely changed, (see next sentence). (The MW and 5w need to be run too). You can do all the gain cals manually but the Utility is soo much easier. Manually you make sure TUN PWR is nor, then set power to 50w EXACTLY, (or 5w for the low cal), then long press XMIT and let it send a carrier for several seconds. You will see the TXGN number change from the default 10 to something (although 10 is a valid number too, just the default and should not be 10 on all bands). For MW, set KXV3 to "test" and set to 1.0mw exactly and TUNE for several seconds) DON'T FORGET TO TAKE IT OUT OF TEST, HI HI, there is NO indication and it will confound you, been there, ha ha. Then Never, ever, EVER set your tx power to *exactly* 5watts, 50watts or 1.0MW ever again because you can inadvertently re-do the tx gain cal and if not into a flat dummy load, you can get it all fouled up. Keith WE6R, Elecraft K3 Tech. On 6/15/2020 1:33 PM, Joseph McIntire wrote: Ok will do. Question though. It is calling it the high power or 50 watt TX gain calibration. Turn off the ATU if you have one. I don't wish I did. But anyway select each band go to tune and verify 50 watts out. Ok I had 50 watts on each. But have not seen in the manual where you would adjust anything if it wasn't. To me thT verifing not calibrating. I also seen on the K3 utility under the calibration tab there is a button for that but it was grayed out and couldn't be selected. How does it work. I have not seen any instructions for doing it that way. Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone *From:* Keith Trinity WE6R *Sent:* Monday, June 15, 2020 2:30:06 PM *To:* Joseph McIntire ; elecraft@mailman.qth.net ; supp...@elecraft.com *Subject:* Re: [Elecraft] Firmware, K3, large jump AB3JN Also we suggest setting the K3 Utility to the ADVANCED mode for more control. Keith WE6R On 6/15/2020 12:27 PM, Joseph McIntire wrote: Ok wel will do that. I do not have the sub receiver so that makes it a little easier. I still have all the original paper work and manuals. I was going to print the latest manuals tonight. I know that there's options in there I don't have but most the functions updated by firmware should be in there. Thank you for your assistance Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone *From:* Keith Trinity WE6R <mailto:ke...@elecraft.com> *Sent:* Monday, June 15, 2020 2:19:54 PM *To:* Joseph McIntire <mailto:ki4...@msn.com>; elecraft@mailman.qth.net <mailto:elecraft@mailman.qth.net> <mailto:elecraft@mailman.qth.net>; supp...@elecraft.com <mailto:supp...@elecraft.com> <mailto:supp...@elecraft.com> *Subject:* Re: [Elecraft] Firmware, K3, large jump AB3JN At this point, I would do the reset, then set RS232 to 38400 to continue on with the DSP load. (reset puts it at 4800 which is SLOW). Then Reset again after FP & DSP have loaded, if you have a sub, you will have to turn it on in config menu, then cycle power, then load DSP2. Then a reset again after all FW is loaded. Then you will have to setup filters, options and do the TX gain cal. The K3 kit build manual has all of that. It will give you confidence you have a clean start. Let us know ... Don't forget to do a new configuration save when it is all setup!! (should you ever have to "go back"). Keith WE6R Elecraft Tech. On 6/15/2020 12:07 PM, Joseph McIntire wrote: Yes that is what happened I just loaded the latest FW the mcu and FPF firmware update went well but when it loaded the DSP when it restarted the radio for some reason it didn't recognize the 2.88 version it had just installed. You know question marks ??.?? For the installed version for the DSP. The others look ok. And I get the ERR AT3. I have not searched yet for other trouble codes. I am at work right now. I will look at it again when I get home. I have been going through the release notes but there is a lot to go through. I will look into the parameter reset also. I will let you know how it goes. Sent from my Verizon, Samsung Galaxy smartphone *From:* Keith Trinity WE6R <mailto:ke...@elecraft.com> *Sent:* Monday, June 15, 2020 1:54:34 PM *To:* elecraft@mailman.qth.net <mailto:elecraft@mailman.qth.net> <mailto:elecraft@mailman.qth.net>; ki4...@msn.com <mailto:ki4...@msn.com>
Re: [Elecraft] Firmware, K3, large jump AB3JN
Ok will do. Question though. It is calling it the high power or 50 watt TX gain calibration. Turn off the ATU if you have one. I don't wish I did. But anyway select each band go to tune and verify 50 watts out. Ok I had 50 watts on each. But have not seen in the manual where you would adjust anything if it wasn't. To me thT verifing not calibrating. I also seen on the K3 utility under the calibration tab there is a button for that but it was grayed out and couldn't be selected. How does it work. I have not seen any instructions for doing it that way. Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone From: Keith Trinity WE6R Sent: Monday, June 15, 2020 2:30:06 PM To: Joseph McIntire ; elecraft@mailman.qth.net ; supp...@elecraft.com Subject: Re: [Elecraft] Firmware, K3, large jump AB3JN Also we suggest setting the K3 Utility to the ADVANCED mode for more control. Keith WE6R On 6/15/2020 12:27 PM, Joseph McIntire wrote: Ok wel will do that. I do not have the sub receiver so that makes it a little easier. I still have all the original paper work and manuals. I was going to print the latest manuals tonight. I know that there's options in there I don't have but most the functions updated by firmware should be in there. Thank you for your assistance Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone From: Keith Trinity WE6R <mailto:ke...@elecraft.com> Sent: Monday, June 15, 2020 2:19:54 PM To: Joseph McIntire <mailto:ki4...@msn.com>; elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net> <mailto:elecraft@mailman.qth.net>; supp...@elecraft.com<mailto:supp...@elecraft.com> <mailto:supp...@elecraft.com> Subject: Re: [Elecraft] Firmware, K3, large jump AB3JN At this point, I would do the reset, then set RS232 to 38400 to continue on with the DSP load. (reset puts it at 4800 which is SLOW). Then Reset again after FP & DSP have loaded, if you have a sub, you will have to turn it on in config menu, then cycle power, then load DSP2. Then a reset again after all FW is loaded. Then you will have to setup filters, options and do the TX gain cal. The K3 kit build manual has all of that. It will give you confidence you have a clean start. Let us know ... Don't forget to do a new configuration save when it is all setup!! (should you ever have to "go back"). Keith WE6R Elecraft Tech. On 6/15/2020 12:07 PM, Joseph McIntire wrote: Yes that is what happened I just loaded the latest FW the mcu and FPF firmware update went well but when it loaded the DSP when it restarted the radio for some reason it didn't recognize the 2.88 version it had just installed. You know question marks ??.?? For the installed version for the DSP. The others look ok. And I get the ERR AT3. I have not searched yet for other trouble codes. I am at work right now. I will look at it again when I get home. I have been going through the release notes but there is a lot to go through. I will look into the parameter reset also. I will let you know how it goes. Sent from my Verizon, Samsung Galaxy smartphone From: Keith Trinity WE6R <mailto:ke...@elecraft.com> Sent: Monday, June 15, 2020 1:54:34 PM To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net> <mailto:elecraft@mailman.qth.net>; ki4...@msn.com<mailto:ki4...@msn.com> <mailto:ki4...@msn.com>; supp...@elecraft.com<mailto:supp...@elecraft.com> <mailto:supp...@elecraft.com> Subject: Re: [Elecraft] Firmware, K3, large jump AB3JN Hi Joe; That is a HUGE jump! ( from 1.96 to 5.67. The oldest I have seen come in was 1.30!!) It is rare, but I have seen a glitch or two in extreme jumps. One is the ADC REF gets set to an invalid voltage of 4.00 which is OUT of RANGE!! Also any saved configs you might load could be an issue if you re-load. I can send you some in-between FW, but it is a LOT OF WORK and is NO guarantee that glitch won't happen. Is there some feature that you are specifically avoiding?? If you don't go with the latest, the Manual etc will not match, nor would any discussion with CS or other folks that are current. Reading the release notes is an excellent idea if you want to look for something specific, or ask me or CS. I *HIGHLY* recommend loading the latest FW and then after do a "Parameter RESET", (EE-INIT-ialization), and then setup and calibrate from SCRATCH. (IE don't load an old config). **That is what I do in repairs (after checking with customer) for such a large jump in FW. Also, that old of a radio will need gold pins and MANY hardware updates, feel free to send it in so I can get my hands on it, hi hi! Keith WE6R, Elecraft K3 Tech __ Elecraft mailing list Home: http://mailman.qth.net/
Re: [Elecraft] Firmware, K3, large jump AB3JN
Also we suggest setting the K3 Utility to the ADVANCED mode for more control. Keith WE6R On 6/15/2020 12:27 PM, Joseph McIntire wrote: Ok wel will do that. I do not have the sub receiver so that makes it a little easier. I still have all the original paper work and manuals. I was going to print the latest manuals tonight. I know that there's options in there I don't have but most the functions updated by firmware should be in there. Thank you for your assistance Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone *From:* Keith Trinity WE6R *Sent:* Monday, June 15, 2020 2:19:54 PM *To:* Joseph McIntire ; elecraft@mailman.qth.net ; supp...@elecraft.com *Subject:* Re: [Elecraft] Firmware, K3, large jump AB3JN At this point, I would do the reset, then set RS232 to 38400 to continue on with the DSP load. (reset puts it at 4800 which is SLOW). Then Reset again after FP & DSP have loaded, if you have a sub, you will have to turn it on in config menu, then cycle power, then load DSP2. Then a reset again after all FW is loaded. Then you will have to setup filters, options and do the TX gain cal. The K3 kit build manual has all of that. It will give you confidence you have a clean start. Let us know ... Don't forget to do a new configuration save when it is all setup!! (should you ever have to "go back"). Keith WE6R Elecraft Tech. On 6/15/2020 12:07 PM, Joseph McIntire wrote: Yes that is what happened I just loaded the latest FW the mcu and FPF firmware update went well but when it loaded the DSP when it restarted the radio for some reason it didn't recognize the 2.88 version it had just installed. You know question marks ??.?? For the installed version for the DSP. The others look ok. And I get the ERR AT3. I have not searched yet for other trouble codes. I am at work right now. I will look at it again when I get home. I have been going through the release notes but there is a lot to go through. I will look into the parameter reset also. I will let you know how it goes. Sent from my Verizon, Samsung Galaxy smartphone *From:* Keith Trinity WE6R <mailto:ke...@elecraft.com> *Sent:* Monday, June 15, 2020 1:54:34 PM *To:* elecraft@mailman.qth.net <mailto:elecraft@mailman.qth.net> <mailto:elecraft@mailman.qth.net>; ki4...@msn.com <mailto:ki4...@msn.com> <mailto:ki4...@msn.com>; supp...@elecraft.com <mailto:supp...@elecraft.com> <mailto:supp...@elecraft.com> *Subject:* Re: [Elecraft] Firmware, K3, large jump AB3JN Hi Joe; That is a HUGE jump! ( from 1.96 to 5.67. The oldest I have seen come in was 1.30!!) It is rare, but I have seen a glitch or two in extreme jumps. One is the ADC REF gets set to an invalid voltage of 4.00 which is OUT of RANGE!! Also any saved configs you might load could be an issue if you re-load. I can send you some in-between FW, but it is a LOT OF WORK and is NO guarantee that glitch won't happen. Is there some feature that you are specifically avoiding?? If you don't go with the latest, the Manual etc will not match, nor would any discussion with CS or other folks that are current. Reading the release notes is an excellent idea if you want to look for something specific, or ask me or CS. I *HIGHLY* recommend loading the latest FW and then after do a "Parameter RESET", (EE-INIT-ialization), and then setup and calibrate from SCRATCH. (IE don't load an old config). **That is what I do in repairs (after checking with customer) for such a large jump in FW. Also, that old of a radio will need gold pins and MANY hardware updates, feel free to send it in so I can get my hands on it, hi hi! Keith WE6R, Elecraft K3 Tech __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Firmware, K3, large jump AB3JN
Ok wel will do that. I do not have the sub receiver so that makes it a little easier. I still have all the original paper work and manuals. I was going to print the latest manuals tonight. I know that there's options in there I don't have but most the functions updated by firmware should be in there. Thank you for your assistance Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone From: Keith Trinity WE6R Sent: Monday, June 15, 2020 2:19:54 PM To: Joseph McIntire ; elecraft@mailman.qth.net ; supp...@elecraft.com Subject: Re: [Elecraft] Firmware, K3, large jump AB3JN At this point, I would do the reset, then set RS232 to 38400 to continue on with the DSP load. (reset puts it at 4800 which is SLOW). Then Reset again after FP & DSP have loaded, if you have a sub, you will have to turn it on in config menu, then cycle power, then load DSP2. Then a reset again after all FW is loaded. Then you will have to setup filters, options and do the TX gain cal. The K3 kit build manual has all of that. It will give you confidence you have a clean start. Let us know ... Don't forget to do a new configuration save when it is all setup!! (should you ever have to "go back"). Keith WE6R Elecraft Tech. On 6/15/2020 12:07 PM, Joseph McIntire wrote: Yes that is what happened I just loaded the latest FW the mcu and FPF firmware update went well but when it loaded the DSP when it restarted the radio for some reason it didn't recognize the 2.88 version it had just installed. You know question marks ??.?? For the installed version for the DSP. The others look ok. And I get the ERR AT3. I have not searched yet for other trouble codes. I am at work right now. I will look at it again when I get home. I have been going through the release notes but there is a lot to go through. I will look into the parameter reset also. I will let you know how it goes. Sent from my Verizon, Samsung Galaxy smartphone From: Keith Trinity WE6R <mailto:ke...@elecraft.com> Sent: Monday, June 15, 2020 1:54:34 PM To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net> <mailto:elecraft@mailman.qth.net>; ki4...@msn.com<mailto:ki4...@msn.com> <mailto:ki4...@msn.com>; supp...@elecraft.com<mailto:supp...@elecraft.com> <mailto:supp...@elecraft.com> Subject: Re: [Elecraft] Firmware, K3, large jump AB3JN Hi Joe; That is a HUGE jump! ( from 1.96 to 5.67. The oldest I have seen come in was 1.30!!) It is rare, but I have seen a glitch or two in extreme jumps. One is the ADC REF gets set to an invalid voltage of 4.00 which is OUT of RANGE!! Also any saved configs you might load could be an issue if you re-load. I can send you some in-between FW, but it is a LOT OF WORK and is NO guarantee that glitch won't happen. Is there some feature that you are specifically avoiding?? If you don't go with the latest, the Manual etc will not match, nor would any discussion with CS or other folks that are current. Reading the release notes is an excellent idea if you want to look for something specific, or ask me or CS. I *HIGHLY* recommend loading the latest FW and then after do a "Parameter RESET", (EE-INIT-ialization), and then setup and calibrate from SCRATCH. (IE don't load an old config). **That is what I do in repairs (after checking with customer) for such a large jump in FW. Also, that old of a radio will need gold pins and MANY hardware updates, feel free to send it in so I can get my hands on it, hi hi! Keith WE6R, Elecraft K3 Tech __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Firmware, K3, large jump AB3JN
At this point, I would do the reset, then set RS232 to 38400 to continue on with the DSP load. (reset puts it at 4800 which is SLOW). Then Reset again after FP & DSP have loaded, if you have a sub, you will have to turn it on in config menu, then cycle power, then load DSP2. Then a reset again after all FW is loaded. Then you will have to setup filters, options and do the TX gain cal. The K3 kit build manual has all of that. It will give you confidence you have a clean start. Let us know ... Don't forget to do a new configuration save when it is all setup!! (should you ever have to "go back"). Keith WE6R Elecraft Tech. On 6/15/2020 12:07 PM, Joseph McIntire wrote: Yes that is what happened I just loaded the latest FW the mcu and FPF firmware update went well but when it loaded the DSP when it restarted the radio for some reason it didn't recognize the 2.88 version it had just installed. You know question marks ??.?? For the installed version for the DSP. The others look ok. And I get the ERR AT3. I have not searched yet for other trouble codes. I am at work right now. I will look at it again when I get home. I have been going through the release notes but there is a lot to go through. I will look into the parameter reset also. I will let you know how it goes. Sent from my Verizon, Samsung Galaxy smartphone *From:* Keith Trinity WE6R *Sent:* Monday, June 15, 2020 1:54:34 PM *To:* elecraft@mailman.qth.net ; ki4...@msn.com ; supp...@elecraft.com *Subject:* Re: [Elecraft] Firmware, K3, large jump AB3JN Hi Joe; That is a HUGE jump! ( from 1.96 to 5.67. The oldest I have seen come in was 1.30!!) It is rare, but I have seen a glitch or two in extreme jumps. One is the ADC REF gets set to an invalid voltage of 4.00 which is OUT of RANGE!! Also any saved configs you might load could be an issue if you re-load. I can send you some in-between FW, but it is a LOT OF WORK and is NO guarantee that glitch won't happen. Is there some feature that you are specifically avoiding?? If you don't go with the latest, the Manual etc will not match, nor would any discussion with CS or other folks that are current. Reading the release notes is an excellent idea if you want to look for something specific, or ask me or CS. I *HIGHLY* recommend loading the latest FW and then after do a "Parameter RESET", (EE-INIT-ialization), and then setup and calibrate from SCRATCH. (IE don't load an old config). **That is what I do in repairs (after checking with customer) for such a large jump in FW. Also, that old of a radio will need gold pins and MANY hardware updates, feel free to send it in so I can get my hands on it, hi hi! Keith WE6R, Elecraft K3 Tech __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Firmware, K3, large jump AB3JN
Yes that is what happened I just loaded the latest FW the mcu and FPF firmware update went well but when it loaded the DSP when it restarted the radio for some reason it didn't recognize the 2.88 version it had just installed. You know question marks ??.?? For the installed version for the DSP. The others look ok. And I get the ERR AT3. I have not searched yet for other trouble codes. I am at work right now. I will look at it again when I get home. I have been going through the release notes but there is a lot to go through. I will look into the parameter reset also. I will let you know how it goes. Sent from my Verizon, Samsung Galaxy smartphone From: Keith Trinity WE6R Sent: Monday, June 15, 2020 1:54:34 PM To: elecraft@mailman.qth.net ; ki4...@msn.com ; supp...@elecraft.com Subject: Re: [Elecraft] Firmware, K3, large jump AB3JN Hi Joe; That is a HUGE jump! ( from 1.96 to 5.67. The oldest I have seen come in was 1.30!!) It is rare, but I have seen a glitch or two in extreme jumps. One is the ADC REF gets set to an invalid voltage of 4.00 which is OUT of RANGE!! Also any saved configs you might load could be an issue if you re-load. I can send you some in-between FW, but it is a LOT OF WORK and is NO guarantee that glitch won't happen. Is there some feature that you are specifically avoiding?? If you don't go with the latest, the Manual etc will not match, nor would any discussion with CS or other folks that are current. Reading the release notes is an excellent idea if you want to look for something specific, or ask me or CS. I *HIGHLY* recommend loading the latest FW and then after do a "Parameter RESET", (EE-INIT-ialization), and then setup and calibrate from SCRATCH. (IE don't load an old config). **That is what I do in repairs (after checking with customer) for such a large jump in FW. Also, that old of a radio will need gold pins and MANY hardware updates, feel free to send it in so I can get my hands on it, hi hi! Keith WE6R, Elecraft K3 Tech __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Firmware, K3, large jump AB3JN
Hi Joe; That is a HUGE jump! ( from 1.96 to 5.67. The oldest I have seen come in was 1.30!!) It is rare, but I have seen a glitch or two in extreme jumps. One is the ADC REF gets set to an invalid voltage of 4.00 which is OUT of RANGE!! Also any saved configs you might load could be an issue if you re-load. I can send you some in-between FW, but it is a LOT OF WORK and is NO guarantee that glitch won't happen. Is there some feature that you are specifically avoiding?? If you don't go with the latest, the Manual etc will not match, nor would any discussion with CS or other folks that are current. Reading the release notes is an excellent idea if you want to look for something specific, or ask me or CS. I *HIGHLY* recommend loading the latest FW and then after do a "Parameter RESET", (EE-INIT-ialization), and then setup and calibrate from SCRATCH. (IE don't load an old config). **That is what I do in repairs (after checking with customer) for such a large jump in FW. Also, that old of a radio will need gold pins and MANY hardware updates, feel free to send it in so I can get my hands on it, hi hi! Keith WE6R, Elecraft K3 Tech __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
