Re: [Elecraft] K-Pod questions
On 5/11/18 at 3:53 PM, r...@tavan.com (Rick Tavan) wrote: On Fri, May 11, 2018 at 2:51 PM, Fred Jensenwrote: Thinking of replacing my Pigknob [which doesn't work when I'm running remote] with a KPod. Couple of questions: 1. If I'm reading the product description correctly the only connection between the K3 and KPod is a cable to the RJ-45 jack on the bottom edge of the Front Panel under the RIT/XIT? Correct, if your K3 is appropriately configured. IIRC, there is a necessary mod to provide adequate power that isn't in all earlier K3's. I run my K*Pod with a single cable. N.B. It's a "special" cable with no connection between the Pins 1, not a standard 6-conductor RJ45 cable. The KPod can also be run with its own power supply. I found the modification to my K3 easy, but I also decided to practice SMD rework and remove the high value resistor and replace it with the low value resistor instead of just paralleling them. (Yeah, I know, I was just showing off.) The bottom line is that you have a bunch of choices how you connect it and power it. I went for minimum cables. 73 Bill AE6JV --- Bill Frantz| When an old person dies, a | Periwinkle (408)356-8506 | library burns. - Joe McGawon | 16345 Englewood Ave www.pwpconsult.com | Irish Ethnographer | Los Gatos, CA 95032 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K-Pod questions
Adding on to what Rick said about the K3 being able to supply power, my K3 does not have the mod so I use an additional USB cable to a powered USB hub to power the K-pod. 73, Dennis NJ6G On 5/11/2018 15:53, Rick Tavan wrote: It's a cool product, Fred. Answers below: /Rick N6XI Rick Tavan Truckee, CA On Fri, May 11, 2018 at 2:51 PM, Fred Jensenwrote: Thinking of replacing my Pigknob [which doesn't work when I'm running remote] with a KPod. Couple of questions: 1. If I'm reading the product description correctly the only connection between the K3 and KPod is a cable to the RJ-45 jack on the bottom edge of the Front Panel under the RIT/XIT? Correct, if your K3 is appropriately configured. IIRC, there is a necessary mod to provide adequate power that isn't in all earlier K3's. I run my K*Pod with a single cable. N.B. It's a "special" cable with no connection between the Pins 1, not a standard 6-conductor RJ45 cable. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K-Pod questions
It's a cool product, Fred. Answers below: /Rick N6XI Rick Tavan Truckee, CA On Fri, May 11, 2018 at 2:51 PM, Fred Jensenwrote: > Thinking of replacing my Pigknob [which doesn't work when I'm running > remote] with a KPod. Couple of questions: > > 1. If I'm reading the product description correctly the only connection > between the K3 and KPod is a cable to the RJ-45 jack on the bottom edge of > the Front Panel under the RIT/XIT? > Correct, if your K3 is appropriately configured. IIRC, there is a necessary mod to provide adequate power that isn't in all earlier K3's. I run my K*Pod with a single cable. N.B. It's a "special" cable with no connection between the Pins 1, not a standard 6-conductor RJ45 cable. > > 2. Is that cable supplied with the KPod? > IIRC, Yes. > > 3. Will the KPod control the remote radio via RemoteRig RRC-1258? > Yes, I do it all the time. I'm using a full K3 as the remote control head. Can't answer for K3/0 or K3/0 Mini. > > 4. Assuming #3 is a Yes and I'm operating a remote K3, where are the > macros stored? > They're stored on the remote K3. The eight buttons on K*Pod launch 16 macros (Tap vs. Hold) stored on the radio. In your case of operating a shared station, you might want to coordinate macro definition with the station owner. Check out the manual, downloadable from Elecraft. /Rick > > OK, that's more than a couple, sorry. TIA > > 73, > > Fred ["Skip"] K6DGW > Sparks NV DM09dn > Washoe County > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to rta...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K-Pod questions (unanswered)
Hi Wes: Currently the K-Pod LEDs work as described. Functionality is being added to the K-Pod that, as a mere "scribe" I don't have yet but have been asked to include tidbits such as the LEDs being programmable. 73, Ron AC7AC -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Wes Stewart Sent: Tuesday, July 19, 2016 10:04 AM To: Elecraft Reflector Subject: [Elecraft] K-Pod questions (unanswered) I'm teetering on the fence about buying one of these or not. I've sent the following directly to Elecraft but haven't received an answer. Perhaps someone else can help. The K-Pod manual mentions LEDs D1-D4 are programmable then goes on to say that D1-D3 are used already. Please clarify and tell me how one would program them. Also there are Aux outputs mentioned, but only in passing. What is the How, What, Where..." The Shipping Status page is out of date. How long ARO is shipping? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to r...@elecraft.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K-Pod questions (unanswered)
I thanked you privately for this, then went to order one. The page has been updated and now they're not shipping until the end of August. On 7/19/2016 10:19 AM, Jim Finan wrote: Ordered one last week and shipped the next day. Now I have one for each radio. Jim Finan AB4AC Sent from my BlackBerry 10 smartphone. Original Message From: Wes Stewart Sent: Tuesday, July 19, 2016 1:06 PM To: Elecraft Reflector Subject: [Elecraft] K-Pod questions (unanswered) I'm teetering on the fence about buying one of these or not. I've sent the following directly to Elecraft but haven't received an answer. Perhaps someone else can help. The K-Pod manual mentions LEDs D1-D4 are programmable then goes on to say that D1-D3 are used already. Please clarify and tell me how one would program them. Also there are Aux outputs mentioned, but only in passing. What is the How, What, Where..." The Shipping Status page is out of date. How long ARO is shipping? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K-Pod questions (unanswered)
Ordered one last week and shipped the next day. Now I have one for each radio. Jim Finan AB4AC Sent from my BlackBerry 10 smartphone. Original Message From: Wes Stewart Sent: Tuesday, July 19, 2016 1:06 PM To: Elecraft Reflector Subject: [Elecraft] K-Pod questions (unanswered) I'm teetering on the fence about buying one of these or not. I've sent the following directly to Elecraft but haven't received an answer. Perhaps someone else can help. The K-Pod manual mentions LEDs D1-D4 are programmable then goes on to say that D1-D3 are used already. Please clarify and tell me how one would program them. Also there are Aux outputs mentioned, but only in passing. What is the How, What, Where..." The Shipping Status page is out of date. How long ARO is shipping? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to jimfi...@att.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K-Pod Questions
If your K3S is connected to your computer, the FT232R USB UART is probably the one in the K3S that connects your computer to the K3S's programming interface. There should also be a USB AUDIO CODEC. When I look at my K-Pod which is connected to the computer for power, I don't see anything. It is probably just looking like a USB charger. 73 Bill AE6JV On 7/12/16 at 5:23 PM, idar...@gmail.com (Irwin Darack) wrote: I just connected my K-Pod to my K3S and have two quick questions: 1. When connected to my computer, what is the name of the Human Interface Device? I have a device showing up as FT232R USB UART? Bill Frantz|"Insofar as the propositions of mathematics refer to 408-356-8506 | reality, they are not certain; and insofar they are www.pwpconsult.com | certain, they do not refer to reality.” -- Einstein --- Bill Frantz| Since the IBM Selectric, keyboards have gotten 408-356-8506 | steadily worse. Now we have touchscreen keyboards. www.pwpconsult.com | Can we make something even worse? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com