Re: [Elecraft] K3 Menu Stuck

[Richard Ferch]

Jim,

This is a bit of a stab in the dark, and may or may not have anything to 
do with what is happening to you, but exactly how many methods are you 
using to do PTT? It sounds as if you may have two or perhaps even three 
methods enabled simultaneously, which is not a good idea and might be 
contributing to the problem by confusing the firmware somehow if the 
hardware and software commands are getting crossed due to slight timing 
differences.

1) MMTTY is controlling PTT on DTR/RTS on COM4, which you have connected 
to the PTT pin on the ACC connector via a keying circuit.

2) You are using MMTTY's Radio command, which means MMTTY will be 
sending TX; and RX; commands over COM1 unless you have deliberately 
blanked out the RX and TX boxes in the Commands pane of the MMTTY Radio 
command dialog box.

3) If you happen to have the PTT box checked for DTR/RTS in the MMTTY 
Radio command dialog (top right), MMTTY is also controlling DTR/RTS on 
COM1, and if you have the K3's CONFIG:PTT-KEY set to anything other than 
OFF-xxx, this would also be commanding the K3's PTT on and off.

Since you have method 1 implemented via the ACC connector, you don't 
really need MMTTY's Radio command at all, at least not for purposes of 
PTT. If you are using Radio command in order to get radio frequency 
information into MMTTY for logging purposes, you might consider:

(a) unchecking the PTT box for DTR/RTS in the MMTTY Radio command dialog 
box; and if this doesn't work or it is already unchecked
(b) clearing out the contents of the Rx and Tx commands in the MMTTY 
Radio command dialog box in order to stop MMTTY from trying to control 
PTT via software.

Hope this helps.

73,
Rich VE3KI
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 Menu Stuck

[Bill Johnson]

I had issues with yesterday's update and did a radio shut down restart.  All 
cured. 
Bill
K9YEQ
K2-#35 (2 more), KX1-#35, K3, TS2000, IC7000, etc.



 
> From: w...@q.com
> To: elecraft@mailman.qth.net
> Date: Tue, 27 Oct 2009 23:24:33 +
> Subject: [Elecraft] K3 Menu Stuck
> 
> 
> 
> Matt,
> 
> Here are the firmware rev's: MCU 3.41, FPF 1.04, DSP 2.37. Several additional 
> pieces of information I have found. In addition to the menu situation as 
> mentioned, when changing modes the mode will not change from CW. Remember you 
> need to go through CW to get from DATA to USB/LSB or vice versa. The problem 
> only occurs when MMTTY is open and the radio is set to FSK D. The situations 
> do NOT occur with Radio Command port set to None (no radio command) nor in 
> other data modes. I have tried MMVARI and Hamscope and it doesn't happen with 
> them but they don't do FSK RTTY. I have a straight through cable from COM 1 
> on my PC to the RS-232 on the K3 for radio command. For FSK RTTY I have a 
> home brew cable with level converters from COM 4 on the PC to the ACC port on 
> the radio. FSK=TXD DB9-3 (PC) to DB15-1, PTT=DB9-7(PC) to DB15-4. Ground 
> =DB9-1 to DB15-5/12. There are two level converters. One each for FSK and PTT 
> and they are in the back shell of the DB9 connector. Each lev
> el converter is a 1k ohm resister from the respective DB9 pin to the base of 
> a 2N3904 transistor. The collectors go to their respective pin on the DB15. 
> Both emitters are tied to the ground pins on each connector.
> 
> FSK RTTY works fine with MMTTY using FSK D on the radio. It's just that the 
> radio gets hung up in the two area mentioned above when radio command is on. 
> I'll try to do some experimenting with radio command to see if there is 
> something that can be changed that will eliminate the situations. 
> 
> Hope the additional information is helpful to anyone trying to duplicate the 
> situation.
> 
> Have a good day and 73.
> 
> Jim, W0EM
> 
> 
> 
> Re: [Elecraft] K3 Menu Stuck
> Matt Zilmer
> 
> Mon, 26 Oct 2009 18:50:48 -0700
> 
> 
> 
> 
> 
> 
> 
> 
> 
> Hi Jim,
> 
> What firmware rev(s) are you using? This doesn't happen with a recent
> field test firmware on the K3 here. No one can confirm your result
> without a rev # for the firmware. It may be revision-dependent and
> probably was eliminated some time ago.
> 
> 73,
> matt W6NIA
> K3 #24
> 
> 
> On Tue, 27 Oct 2009 01:38:55 +, you wrote:
> 
> >
> >Hi,
> >
> >Just discovered something that doesn't seem right. When I hit MENU and turn 
> >VFO B to RPT OFS the display stays on that regardless whether turning VFO B 
> >forward or backwards. It only sticks on that entry. It sticks regardless of 
> >which way (CW or CCW) I approach the entry. The only way to get out of it is 
> >to turn the radio off and back on. 
> >
> >Anyone have any ideas on what is happening and how to correct it.
> >
> >Have a good day and 73.
> >
> >Jim, W0EM
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
  
_
Windows 7: It works the way you want. Learn more.
http://www.microsoft.com/Windows/windows-7/default.aspx?ocid=PID24727::T:WLMTAGL:ON:WL:en-US:WWL_WIN_evergreen2:102009
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 Menu Stuck

[Matt Zilmer]

Hi Jim,

What firmware rev(s) are you using?  This doesn't happen with a recent
field test firmware on the K3 here.  No one can confirm your result
without a rev # for the firmware.  It may be revision-dependent and
probably was eliminated some time ago.

73,
matt W6NIA
K3 #24


On Tue, 27 Oct 2009 01:38:55 +, you wrote:

>
>Hi,
>
>Just discovered something that doesn't seem right.  When I hit MENU and turn 
>VFO B to RPT OFS the display stays on that regardless whether turning VFO B 
>forward or backwards.  It only sticks on that entry.  It sticks regardless of 
>which way (CW or CCW) I approach the entry.  The only way to get out of it is 
>to turn the radio off and back on.  
>
>Anyone have any ideas on what is happening and how to correct it.
>
>Have a good day and 73.
>
>Jim, W0EM
>
>
> 
>__
>Elecraft mailing list
>Home: http://mailman.qth.net/mailman/listinfo/elecraft
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:Elecraft@mailman.qth.net
>
>This list hosted by: http://www.qsl.net
>Please help support this email list: http://www.qsl.net/donate.html
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html