Re: [Elecraft] When to use the preamp on the K3/K3S
I make a deliberate choice to set the AGC threshold low, so I DO get AGC action on weak signals. Perhaps my ears just don't have the dynamic range they used to, but I find otherwise the strong signals are just uncomfortably loud. Yes, I have to ride the RF gain to distinguish signals of different strengths, but I find that a fair trade-off. Give the average age of hams these days, I doubt I'm the only one with such issues. Of course, younger operators may want to treat their ears gently, to preserve that good dynamic range. Note that high acoustic background noise can further reduce the difference between audible and painful. The Radiosport headset is the best remedy I've found for that, short of putting the amplifier in another room. 73, Scott K9MA On 5/23/2018 15:37, Al Lorona wrote: Scott, If the weakest signals are already activating the AGC, that's the exact condition that leads to the many 'my K3 is noisy' complaints that we see here. Plus, that tends to make all signals sound like they're the same strength, another complaint we've heard in the past. In fact, you don't want weak signals activating AGC. You want strong signals, above a certain threshhold (AGC THR on the K3) to activate it. This gives you a nice, quiet linear region where weak signals sound weak, and stronger signals sound stronger. In addition, overload should not determine whether you turn off the preamp! That's way bad advice. Here's the general principle: you should only use as much gain as you need. AF as well as RF. Less is usually better. Your ears will not be blown by reducing your receiver gain. R, Al W6LX -- Scott K9MA k...@sdellington.us __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] When to use the preamp on the K3/K3S
There are guidelines on my website www.w3fpr.com for how to set the K3/K3S AGC Threshold and Slope for best results. See the "Noisy K3" article. 73, Don W3FPR On 5/23/2018 4:37 PM, Al Lorona wrote: Scott, If the weakest signals are already activating the AGC, that's the exact condition that leads to the many 'my K3 is noisy' complaints that we see here. Plus, that tends to make all signals sound like they're the same strength, another complaint we've heard in the past. In fact, you don't want weak signals activating AGC. You want strong signals, above a certain threshhold (AGC THR on the K3) to activate it. This gives you a nice, quiet linear region where weak signals sound weak, and stronger signals sound stronger. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] When to use the preamp on the K3/K3S
In the K3/K3S/KX2/KX3, "RF Gain" adjusts receive path gain ahead of the AGC detector while "AF Gain" adjusts the receive path gain AFTER the AGC, if any, is applied. 73, Lyle KK7P ... "RF Gain" in modern receivers really just sets the maximum gain the AGC will allow, so reducing it only attenuates weaker signals. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] When to use the preamp on the K3/K3S
Scott, If the weakest signals are already activating the AGC, that's the exact condition that leads to the many 'my K3 is noisy' complaints that we see here. Plus, that tends to make all signals sound like they're the same strength, another complaint we've heard in the past. In fact, you don't want weak signals activating AGC. You want strong signals, above a certain threshhold (AGC THR on the K3) to activate it. This gives you a nice, quiet linear region where weak signals sound weak, and stronger signals sound stronger. In addition, overload should not determine whether you turn off the preamp! That's way bad advice. Here's the general principle: you should only use as much gain as you need. AF as well as RF. Less is usually better. Your ears will not be blown by reducing your receiver gain. R, Al W6LX __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] When to use the preamp on the K3/K3S
The problem with simply reducing the gain is that the AGC may become
ineffective, forcing the operator to increase audio gain on weak
signals. Then the strong signals can be loud enough to be
uncomfortable, or even cause hearing damage. I like to keep the gain
high enough to get some AGC action on the weakest signals, and reduce
"RF Gain" when necessary to distinguish stronger signals from weaker
ones. "RF Gain" in modern receivers really just sets the maximum gain
the AGC will allow, so reducing it only attenuates weaker signals.
That said, turning off the preamp and/or enabling the attenuator should
be necessary only if strong signals are causing overload. Of course, if
the receiver has enough gain for a low enough noise floor and good AGC
operation on weak signals with the preamp off, there's no advantage in
using it.
73,
Scott K9MA
On 5/23/2018 08:07, Bob McGraw K4TAX wrote:
One of the topics I've discussed with with noted engineers has to do
with use of a Preamp and use of the Attenuator and use of the RF Gain
control. In general the optimum legacy receiver performance occurs
when the receiver noise floor is some 10 db below band noise. Being
such, how does one attain this? If the no signal band noise is S-5
or -97 dBm, and receiver noise floor is -133 dBm {i.e K3S}, this says
one should use a combination to total 26 dB Attenuation and RF Gain
reduction. Certainly one would NOT want to have a Preamp engaged
under these conditions. Likewise, if the band noise is -121 dBm or
about S-1 and the receiver noise is -138 dBm {Preamp engaged} one
might wish to reduce the RF Gain a bit.
From experience and my observing other hams operations, many seem to
think more gain is needed to hear or pull out weak signals from the
noise. I find the proper use of the Preamp and specially the correct
amount of Attenuation and RF Gain reduction, weak signals seem to pop
out of the noise.
73
Bob, K4TAX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to k...@sdellington.us
--
Scott K9MA
k...@sdellington.us
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com
