Re: [PSES] High Touch Current in Industrial Machinery

[Stultz, Mark]

Hi Brian,
Since this is machinery, typically IEC 60204-1 would be applied.  Check out 
clause 8.2.6 Additional requirements for electrical equipment having earth 
leakage currents higher than 10 mA.

Best regards,

Mark Stultz | CMSE(r) | Sealed Air | AUTOBAG(r) brand Equipment | Streetsboro, 
OH | 330-342-2402

From: Brian Kunde 
Sent: Friday, February 16, 2024 4:24 PM
To: EMC-PSTC@LISTSERV.IEEE.ORG
Subject: [PSES] High Touch Current in Industrial Machinery

You don't often get email from 
bkundew...@gmail.com. Learn why this is 
important

 CAUTION: This email originated from outside of the organization. Do not click 
links or open attachments unless you recognize the sender and know the content 
is safe.

I am working on an Industrial Machine with a 3-phase 5hp motor driven by a VFD. 
To pass the EMC conducted emissions requirements, we had to add a RF Line 
Filter that is recommended by the VFD manufacturer.  This filter has large 
Y-Caps. I know these currents theoretically cancel out in a balanced system, 
but when performing the traditional Touch Current test according to IEC 60990 
6.2.2.2, Fault Condition No. 1 (open Protective Conductor) we measure a current 
about 50mA.

However, the standard says that "this subclause do not apply to reliably 
earthed equipment. . . .". This Industrial Machine is either permanently wired 
or it can use an industrial grade plug and socket, so this fault test would not 
apply.

So even though the measured current is high if we perform this fault test, 
because the machine is well grounded I do not have to do anything?

In contrast, the IEC 62368 would require a warning label, warning in the 
manual, and a secondary PE terminal.

I have read comments online such as, "in the industrial environment, they don't 
give a hoot about leakage current." Is this true?

On the other hand, an industrial machine could be the size of a building and 
have dozens of VFD driven motors and line filters creating a huge amounts of 
currents in an unbalance environment. So in my case, do I have any concerns 
other than to insure the machine is well bonded to PE during installation? But 
isn't this a normal installation consideration?

Thanks to all.
The Other Brian


This message is from the IEEE Product Safety Engineering Society emc-pstc 
discussion list. To post a message to the list, send your e-mail to 
EMC-PSTC@LISTSERV.IEEE.ORG
All emc-pstc postings are archived and searchable on the web at:
https://www.mail-archive.com/emc-pstc@listserv.ieee.org/

Website: https://ewh.ieee.org/soc/pses/
Instructions: https://ewh.ieee.org/soc/pses/list.html (including how to 
unsubscribe)
List rules: https://ewh.ieee.org/soc/pses/listrules.html

For help, send mail to the list administrators:
Mike Sherman at: msherma...@comcast.net
Rick Linford at: linf...@ieee.org

For policy questions, send mail to:
Jim Bacher at: j.bac...@ieee.org



To unsubscribe from the EMC-PSTC list, click the following link: 
https://listserv.ieee.org/cgi-bin/wa?SUBED1=EMC-PSTC=1

-

This message is from the IEEE Product Safety Engineering Society emc-pstc 
discussion list. To post a message to the list, send your e-mail to 
EMC-PSTC@LISTSERV.IEEE.ORG

All emc-pstc postings are archived and searchable on the web at:
https://www.mail-archive.com/emc-pstc@listserv.ieee.org/

Website:  https://ewh.ieee.org/soc/pses/
Instructions:  https://ewh.ieee.org/soc/pses/list.html (including how to 
unsubscribe)
List rules: https://ewh.ieee.org/soc/pses/listrules.html

For help, send mail to the list administrators:
Mike Sherman at: msherma...@comcast.net
Rick Linford at: linf...@ieee.org

For policy questions, send mail to:
Jim Bacher:  
_
To unsubscribe from the EMC-PSTC list, click the following link: 
https://listserv.ieee.org/cgi-bin/wa?SUBED1=EMC-PSTC=1

[PSES] High Touch Current in Industrial Machinery

[Brian Kunde]

I am working on an Industrial Machine with a 3-phase 5hp motor driven by a
VFD. To pass the EMC conducted emissions requirements, we had to add a RF
Line Filter that is recommended by the VFD manufacturer.  This filter has
large Y-Caps. I know these currents theoretically cancel out in a balanced
system, but when performing the traditional Touch Current test according to
IEC 60990 6.2.2.2, Fault Condition No. 1 (open Protective Conductor) we
measure a current about 50mA.

However, the standard says that "this subclause do not apply to reliably
earthed equipment. . . .". This Industrial Machine is either permanently
wired or it can use an industrial grade plug and socket, so this fault test
would not apply.

So even though the measured current is high if we perform this fault test,
because the machine is well grounded I do not have to do anything?

In contrast, the IEC 62368 would require a warning label, warning in the
manual, and a secondary PE terminal.

I have read comments online such as, "in the industrial environment, they
don't give a hoot about leakage current." Is this true?

On the other hand, an industrial machine could be the size of a building
and have dozens of VFD driven motors and line filters creating a huge
amounts of currents in an unbalance environment. So in my case, do I have
any concerns other than to insure the machine is well bonded to PE during
installation? But isn't this a normal installation consideration?

Thanks to all.
The Other Brian

-

This message is from the IEEE Product Safety Engineering Society emc-pstc 
discussion list. To post a message to the list, send your e-mail to 
EMC-PSTC@LISTSERV.IEEE.ORG

All emc-pstc postings are archived and searchable on the web at:
https://www.mail-archive.com/emc-pstc@listserv.ieee.org/

Website:  https://ewh.ieee.org/soc/pses/
Instructions:  https://ewh.ieee.org/soc/pses/list.html (including how to 
unsubscribe)
List rules: https://ewh.ieee.org/soc/pses/listrules.html

For help, send mail to the list administrators:
Mike Sherman at: msherma...@comcast.net
Rick Linford at: linf...@ieee.org

For policy questions, send mail to:
Jim Bacher:  
_
To unsubscribe from the EMC-PSTC list, click the following link: 
https://listserv.ieee.org/cgi-bin/wa?SUBED1=EMC-PSTC=1