Re: [expert] Mdk8 - install goes ok but X refuses to start

2001-05-09 Thread John Wolford

I had the same thing happen for me w/ a few 7.2 installs. It got to the point
that i would install it but not test it, just so the install could finish. Then
it (X) would usually start up tho, i think (i can't remember). I invoked it
with startx. That was around the time that i was shutting down absolutely every
service and opening them up as needed - so i shut down xfs without knowing what
it did. X didn't start up (naturally) and then as i stared at the error
messages the gears started to turn and i started up xfs again and it worked. I
don't think i've ever had X not work after a successful install unless i
fiddled with the settings or changed video cards (god help me if i do something
like that, i'm not good enough with the hardware/software interfacing to fix
something like that).

Don't know if that helps, but there is my $0.02 :-)
j


--- Mike Rambo <[EMAIL PROTECTED]> wrote:
> At the start, I'd appreciate it if anyone responding would copy my email
> address. I somehow got dropped from the list about a month ago and for
> some reason have been unable to re-subscribe (or else my employer is
> filtering email from mandrake somehow).
> 
> I have installed Mdk8 (from .iso) on two different machines (Dell P166,
> 64MB, 6GB IDE and Gateway Celeron 500, I810 chipset, 64MB, 8.6GB IDE)
> and have ended up with the same problem on both. The install goes fine
> including the setup and testing of X but upon rebooting both machines
> try to start X and end up dropping back to the CLI. Manual attempts to
> start X fail as well. I have looked through the list archives and
> haven't seen any other references to this problem (makes me wonder what
> I've done).
> 
> install.log on the Gateway shows these three things - 
> 
> *perl setting locale failed
> *unpacking cpio archive - bad magic
> *glibc-2.2.2 install failed exit status 127
> 
> I haven't been able to check the Dell install for similar entries yet.
> /var/log/messages and /var/log/XFree86.0.log show nothing helpful
> either.
> 
> Anyone have any insight on this problem?
> 
> 
> -- 
> Mike Rambo
> [EMAIL PROTECTED]
> 


__
Do You Yahoo!?
Yahoo! Auctions - buy the things you want at great prices
http://auctions.yahoo.com/




[expert] Mdk8 - install goes ok but X refuses to start

2001-05-09 Thread Mike Rambo

At the start, I'd appreciate it if anyone responding would copy my email
address. I somehow got dropped from the list about a month ago and for
some reason have been unable to re-subscribe (or else my employer is
filtering email from mandrake somehow).

I have installed Mdk8 (from .iso) on two different machines (Dell P166,
64MB, 6GB IDE and Gateway Celeron 500, I810 chipset, 64MB, 8.6GB IDE)
and have ended up with the same problem on both. The install goes fine
including the setup and testing of X but upon rebooting both machines
try to start X and end up dropping back to the CLI. Manual attempts to
start X fail as well. I have looked through the list archives and
haven't seen any other references to this problem (makes me wonder what
I've done).

install.log on the Gateway shows these three things - 

*perl setting locale failed
*unpacking cpio archive - bad magic
*glibc-2.2.2 install failed exit status 127

I haven't been able to check the Dell install for similar entries yet.
/var/log/messages and /var/log/XFree86.0.log show nothing helpful
either.

Anyone have any insight on this problem?


-- 
Mike Rambo
[EMAIL PROTECTED]