Re: [expert] SB AWE64 failing to load - Mandrake 8.1
On October 27, 2001 06:33 pm, you wrote: > Try this. > > 1. Remark or remove an reference to a sound card in your > /etc/modules.conf file, then do a depmod -ae. > > > 2. Reboot and go into your BIOS and insure that PNP OS is set to NO. > > 3. Prossible when Linux reboots new hardware will be found. > > if not > > 4. Got to the control center and configure your SB 64 there. > > Good luck > > Larry You da man! That did the trick. My modules.conf had no references, but PNP OS was on in the BIOS. I turned that off, but Control Center still couldn't configure it. I tried sndconfig and it worked! Thanks everyone for your help. I'm listening to my mp3's again. -Eric -- arctic bears - email and name services 25 email addresses@yourdomain CA$11.95/month DNS starting at CA$3.49/month - domains from CA$25.95/year for details contact [EMAIL PROTECTED] or visit http://www.arcticbears.com Want to buy your Pack or Services from MandrakeSoft? Go to http://www.mandrakestore.com
Re: [expert] SB AWE64 failing to load - Mandrake 8.1
Eric Paynter wrote: > > I recently upgraded (read: re-installed) to Mandrake 8.1. Since then, my > sound card has not been working. The sound card was working fine under > Mandrake 8.0 and still works when I boot to Win98SE. It's a Creative SB AWE64. > > When I run sndconfig, it first says: > > > ISAPNP Probe Results > > A ISAPNP sound card was found in > your system. The details are: > > Model: Creative SB AWE64 > PnP:Audio > > > OK. All looks good so far. Hit OK for the sound sample, and I get: > > > modprobe error > > The following error occurred running the modprobe program: > > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: > init_module: No such device > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: insmod > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz failed > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: insmod > sound-slot-0 failed > > > OK. Not so good... It spits me into manual config and I try a zillion > combinations for IRQ/IO/DMA including those which work for Win98 and still, > the same thing comes out. Also, I'm not sure if this is relavent, but when I > probe the driver with insmod, it returns unresolved symbols. Is this supposed > to happen? Maybe my sb.o is corrupt? > > > [eric@europa eric]$ /sbin/insmod -p sb > Using /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: unresolved symbol > probe_sbmpu_Rddc8ad00 > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: unresolved symbol > smw_free_R450f9aea > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: unresolved symbol > sb_dsp_detect_Rd8a2731c > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: unresolved symbol > sb_dsp_unload_Rc4884969 > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: unresolved symbol > unload_sbmpu_R74afd69c > /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: unresolved symbol > sb_dsp_init_Re986438b > > > Thanks for any help getting this working, > > -Eric Try this. 1. Remark or remove an reference to a sound card in your /etc/modules.conf file, then do a depmod -ae. 2. Reboot and go into your BIOS and insure that PNP OS is set to NO. 3. Prossible when Linux reboots new hardware will be found. if not 4. Got to the control center and configure your SB 64 there. Good luck Larry -- Sword'sEdge Want to buy your Pack or Services from MandrakeSoft? Go to http://www.mandrakestore.com
Re: [expert] SB AWE64 failing to load - Mandrake 8.1
That's even more interesting seeing as how I haven't recompiled the kernel. It's the 2.4.8 kernel that was released as a security patch a few weeks ago... -Eric On October 27, 2001 03:00 pm, you wrote: > It looks as if isa_pnp is linked into the kernel: > # > # Plug and Play configuration > # > CONFIG_PNP=y > CONFIG_ISAPNP=y > CONFIG_PNPBIOS=y > > -- Bjarne > > Eric Paynter wrote: > > OK. lsmod returns nothing that seems related to sound. Here is the > > output: > > > > > > [root@europa etc]# lsmod > > Module Size Used by > > binfmt_misc 6208 1 > > nfsd 70464 8 (autoclean) > > lockd 51440 1 (autoclean) [nfsd] > > sunrpc 66480 1 (autoclean) [nfsd lockd] > > lp 5808 0 > > parport_pc 20240 1 > > parport24768 1 [lp parport_pc] > > af_packet 12560 0 (autoclean) > > usb-uhci 21232 0 (unused) > > usbcore50752 1 [usb-uhci] > > tulip 36400 1 (autoclean) > > nls_iso8859-1 2880 1 (autoclean) > > ntfs 49776 1 (autoclean) > > rtc 5600 0 (autoclean) > > ext3 63084 1 > > jbd39168 1 [ext3] > > > > > > So I can't unload anything. I went into the Control Center and when I try > > to test the card, I get "modprobe: Can't locate module isa-pnp". I > > scanned my HDD and sure enough there is no module by that name... I can't > > find any rpm on the CD that claims to have that file either. Now I'm > > really confused. Does Mdk8.1 not support isa-pnp anymore? That doesn't > > make sense so I must have missed something. This was a pretty vanilla > > install. I just chose "recommended" and selected all the workstation > > stuff and none of the server stuff so I can't imagine that I "decided" > > not to install it. > > > > Any other ideas? > > > > Thanks, > > > > -Eric > > > > On October 27, 2001 12:04 pm, Jose M. Sanchez wrote: > > > A frequent mistake people make when using sndconfig is NOT first > > > clearing the existing sound modules from RAM. > > > > > > If you don't clear them sndconfig cannot load them again, since they > > > already exist and interfere with the new load (unless you happen to > > > have two identical boards). > > > > > > Under LM8.1 sndconfig does not fully configure many sound cards. The > > > Mandrake Control Panel does a MUCH BETTER job. > > > > > > Remove all sound related modules from RAM > > > > > > "lsmod" > > > > > > "rmmod sound" etc. > > > > > > If rmmod states that a mod is busy, there is another module which must > > > be removed first... > > > > > > Get rid of all of them then go into the control panel and configure > > > your card from their. > > > > > > Reboot (yeah really, restarting the sound daemon does not seem to give > > > you all the new device entries). > > > > > > Use AUXMIX to turn up all the mixer values and go back into the > > > KDEcontrol Panel and "Save" the mixer state, so that things get > > > automatically set upon the next boot. > > > > > > The KDEcontrol panel modifies the ALSA-CTL files which are used at > > > boot. > > > > > > -JMS > > > > > > |-Original Message- > > > |From: [EMAIL PROTECTED] > > > |[mailto:[EMAIL PROTECTED]] On Behalf Of Eric Paynter > > > |Sent: Saturday, October 27, 2001 2:40 PM > > > |To: [EMAIL PROTECTED] > > > |Subject: [expert] SB AWE64 failing to load - Mandrake 8.1 > > > | > > > | > > > |I recently upgraded (read: re-installed) to Mandrake 8.1. > > > |Since then, my > > > |sound card has not been working. The sound card was working fine under > > > |Mandrake 8.0 and still works when I boot to Win98SE. It's a > > > |Creative SB AWE64. > > > | > > > |When I run sndconfig, it first says: > > > | > > > | > > > |ISAPNP Probe Results > > > | > > > | A ISAPNP sound card was found in > > > | your system. The details are: > > > | > > > | Model: Creative SB AWE64 > > > | PnP:Audio > > > | > > > | > > > |OK. All looks good so far. Hit OK for the sound sample, and I get: > > > | > > > | > > > |modprobe error > > > | > > > | The following error occurred running the modprobe program: > > > | > > > | /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: > > > | init_module: No such device > > > | /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: insmod > > > | /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz failed > > > | /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: insmod > > > | sound-slot-0 failed > > > | > > > |OK. Not so good... It spits me into manual config and I try a zillion > > > |combinations for IRQ/IO/DMA including those which work for > > > |Win98 and still, > > > |the same thing comes out. Also, I'm not sure if this is > > > |relavent, but when I > > > |probe the driver with insmod, it returns unresolved symbols. > > > |Is this supposed > >
Re: [expert] SB AWE64 failing to load - Mandrake 8.1
It looks as if isa_pnp is linked into the kernel: # # Plug and Play configuration # CONFIG_PNP=y CONFIG_ISAPNP=y CONFIG_PNPBIOS=y -- Bjarne Eric Paynter wrote: > > OK. lsmod returns nothing that seems related to sound. Here is the output: > > > [root@europa etc]# lsmod > Module Size Used by > binfmt_misc 6208 1 > nfsd 70464 8 (autoclean) > lockd 51440 1 (autoclean) [nfsd] > sunrpc 66480 1 (autoclean) [nfsd lockd] > lp 5808 0 > parport_pc 20240 1 > parport24768 1 [lp parport_pc] > af_packet 12560 0 (autoclean) > usb-uhci 21232 0 (unused) > usbcore50752 1 [usb-uhci] > tulip 36400 1 (autoclean) > nls_iso8859-1 2880 1 (autoclean) > ntfs 49776 1 (autoclean) > rtc 5600 0 (autoclean) > ext3 63084 1 > jbd39168 1 [ext3] > > > So I can't unload anything. I went into the Control Center and when I try to > test the card, I get "modprobe: Can't locate module isa-pnp". I scanned my > HDD and sure enough there is no module by that name... I can't find any rpm > on the CD that claims to have that file either. Now I'm really confused. Does > Mdk8.1 not support isa-pnp anymore? That doesn't make sense so I must have > missed something. This was a pretty vanilla install. I just chose > "recommended" and selected all the workstation stuff and none of the server > stuff so I can't imagine that I "decided" not to install it. > > Any other ideas? > > Thanks, > > -Eric > > On October 27, 2001 12:04 pm, Jose M. Sanchez wrote: > > A frequent mistake people make when using sndconfig is NOT first > > clearing the existing sound modules from RAM. > > > > If you don't clear them sndconfig cannot load them again, since they > > already exist and interfere with the new load (unless you happen to have > > two identical boards). > > > > Under LM8.1 sndconfig does not fully configure many sound cards. The > > Mandrake Control Panel does a MUCH BETTER job. > > > > Remove all sound related modules from RAM > > > > "lsmod" > > > > "rmmod sound" etc. > > > > If rmmod states that a mod is busy, there is another module which must > > be removed first... > > > > Get rid of all of them then go into the control panel and configure your > > card from their. > > > > Reboot (yeah really, restarting the sound daemon does not seem to give > > you all the new device entries). > > > > Use AUXMIX to turn up all the mixer values and go back into the > > KDEcontrol Panel and "Save" the mixer state, so that things get > > automatically set upon the next boot. > > > > The KDEcontrol panel modifies the ALSA-CTL files which are used at boot. > > > > -JMS > > > > |-Original Message- > > |From: [EMAIL PROTECTED] > > |[mailto:[EMAIL PROTECTED]] On Behalf Of Eric Paynter > > |Sent: Saturday, October 27, 2001 2:40 PM > > |To: [EMAIL PROTECTED] > > |Subject: [expert] SB AWE64 failing to load - Mandrake 8.1 > > | > > | > > |I recently upgraded (read: re-installed) to Mandrake 8.1. > > |Since then, my > > |sound card has not been working. The sound card was working fine under > > |Mandrake 8.0 and still works when I boot to Win98SE. It's a > > |Creative SB AWE64. > > | > > |When I run sndconfig, it first says: > > | > > | > > |ISAPNP Probe Results > > | > > | A ISAPNP sound card was found in > > | your system. The details are: > > | > > | Model: Creative SB AWE64 > > | PnP:Audio > > | > > | > > |OK. All looks good so far. Hit OK for the sound sample, and I get: > > | > > | > > |modprobe error > > | > > | The following error occurred running the modprobe program: > > | > > | /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: > > | init_module: No such device > > | /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: insmod > > | /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz failed > > | /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: insmod > > | sound-slot-0 failed > > | > > |OK. Not so good... It spits me into manual config and I try a zillion > > |combinations for IRQ/IO/DMA including those which work for > > |Win98 and still, > > |the same thing comes out. Also, I'm not sure if this is > > |relavent, but when I > > |probe the driver with insmod, it returns unresolved symbols. > > |Is this supposed > > |to happen? Maybe my sb.o is corrupt? > > | > > | > > |[eric@europa eric]$ /sbin/insmod -p sb > > |Using /lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz > > |/lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: > > |unresolved symbol > > |probe_sbmpu_Rddc8ad00 > > |/lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: > > |unresolved symbol > > |smw_free_R450f9aea > > |/lib/modules/2.4.8-26mdk/kernel/drivers/sound/sb.o.gz: > > |unresolved symbol