[Flexradio] Looking for a Flex SDR-1000
Hello, I am Looking for a Flex SDR-1000 and Sound Card D44 or Edirol FA-66 and all cables needed for operation. Want it to be the 100W version and hopefully a newer version with the 8pin front mic connector. Please Email : yb...@yahoo.com Regard's Yose Ferry YB0AR www.qrz.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] FLEX 5000A Possible PTT Issues when using WINMOOR
Try changing the VAC driver to WDM-KS. Make sure that the digi mode program is not running when you make change. -Tim Sent from my iPhone On Oct 3, 2009, at 10:52 PM, "Allen Shuff" wrote: > Tim, > My settings are - SR 96kHz, buffer 1024, VAC Driver MME, Input Line1 > (virtual Audio Cable), output line2 (virtual audio cable), buffer > size 1024, > sample rate 48000, Allow PTT to override/bypass for phone is > checked, TX > gain is 2, TX Gain is 16, latency manual NOT checked, latency ms 120. > > Allen > > > > > > > - Original Message - > From: "Tim Ellison" > To: "Allen Shuff" > Cc: ; > Sent: Saturday, October 03, 2009 7:32 PM > Subject: Re: [Flexradio] FLEX 5000A Possible PTT Issues when using > WINMOOR > > > What are yourFirewire/audio (SR & buffer) and VAC settings in > PowerSDR? I do not think it is a PTT issue but the first part of the > AF from the digi mode program is is being cut off. > > -Tim > > Sent from my iPhone > > On Oct 3, 2009, at 9:47 PM, "Allen Shuff" > wrote: > >> I am using the FLEX 5000A for WINMOOR and have had no problems >> establishing communications; however, I have had troubles passing >> messages. I have received the following comments from two different >> stations: >> >> 10/04 00:15 W9ON - sounds like a PTT problem on your >> transmission - first part of PSK signal cutting out >> >> 10/03 23:43 w9on - lots of "Sumcheck Fail" on your ACKs >> >> I am using a DELL Slim Studio with core 2 QUAD CPU Q8300 @2.5GHz >> OS: 64-bit VISTA >> >> USING VAC for audio >> >> com0com 2.2.1.0-x64 >> Power SDR PTT enable port 17 with RTS and DTR enabled >> >> WINMOOR SETUP: PTT PORT 7 RTS and DTRchecked >> PTT Baud Rate 4800 >> >> I have attached my debug log. >> >> >> Allen, W9ON >> ___ >> FlexRadio Systems Mailing List >> FlexRadio@flex-radio.biz >> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz >> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ >> Knowledge Base: http://kc.flex-radio.com/ Homepage: >> http://www.flex-radio.com/ >> Message delivered to telli...@itsco.com > ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] FLEX 5000A Possible PTT Issues when using WINMOOR
Tim, My settings are - SR 96kHz, buffer 1024, VAC Driver MME, Input Line1 (virtual Audio Cable), output line2 (virtual audio cable), buffer size 1024, sample rate 48000, Allow PTT to override/bypass for phone is checked, TX gain is 2, TX Gain is 16, latency manual NOT checked, latency ms 120. Allen - Original Message - From: "Tim Ellison" To: "Allen Shuff" Cc: ; Sent: Saturday, October 03, 2009 7:32 PM Subject: Re: [Flexradio] FLEX 5000A Possible PTT Issues when using WINMOOR What are yourFirewire/audio (SR & buffer) and VAC settings in PowerSDR? I do not think it is a PTT issue but the first part of the AF from the digi mode program is is being cut off. -Tim Sent from my iPhone On Oct 3, 2009, at 9:47 PM, "Allen Shuff" wrote: I am using the FLEX 5000A for WINMOOR and have had no problems establishing communications; however, I have had troubles passing messages. I have received the following comments from two different stations: 10/04 00:15 W9ON - sounds like a PTT problem on your transmission - first part of PSK signal cutting out 10/03 23:43 w9on - lots of "Sumcheck Fail" on your ACKs I am using a DELL Slim Studio with core 2 QUAD CPU Q8300 @2.5GHz OS: 64-bit VISTA USING VAC for audio com0com 2.2.1.0-x64 Power SDR PTT enable port 17 with RTS and DTR enabled WINMOOR SETUP: PTT PORT 7 RTS and DTRchecked PTT Baud Rate 4800 I have attached my debug log. Allen, W9ON ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to telli...@itsco.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] FLEX 5000A Possible PTT Issues when using WINMOOR
What are yourFirewire/audio (SR & buffer) and VAC settings in PowerSDR? I do not think it is a PTT issue but the first part of the AF from the digi mode program is is being cut off. -Tim Sent from my iPhone On Oct 3, 2009, at 9:47 PM, "Allen Shuff" wrote: > I am using the FLEX 5000A for WINMOOR and have had no problems > establishing communications; however, I have had troubles passing > messages. I have received the following comments from two different > stations: > > 10/04 00:15 W9ON - sounds like a PTT problem on your > transmission - first part of PSK signal cutting out > > 10/03 23:43 w9on - lots of "Sumcheck Fail" on your ACKs > > I am using a DELL Slim Studio with core 2 QUAD CPU Q8300 @2.5GHz > OS: 64-bit VISTA > > USING VAC for audio > > com0com 2.2.1.0-x64 > Power SDR PTT enable port 17 with RTS and DTR enabled > > WINMOOR SETUP: PTT PORT 7 RTS and DTRchecked > PTT Baud Rate 4800 > > I have attached my debug log. > > > Allen, W9ON > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kc.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > Message delivered to telli...@itsco.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] Health news regarding John Basilotto, W5GI
This is horrible news. Why does this seem to happen to the good people? Burt ngblood wrote: > From: Gerald Youngblood > Subject: [Flexradio] Health news regarding John Basilotto, W5GI > To: flexradio@flex-radio.biz > Date: Saturday, October 3, 2009, 9:57 AM > Dear FlexRadio customers, > > Many of you know our friend and colleague, John Basilotto > W5GI, who retired > from FlexRadio a couple months ago due to an undiagnosed > health problem. On > Thursday, John came by the office to tell us that he has > been diagnosed with > pancreatic cancer. He plans to meet with an > oncologist soon to see what > treatment options he may have, if any. > > John has a great attitude and he plans to stay as active as > he can, > including on the air. In fact, he is at the Belton, > Texas Hamfest this > morning selling off a lot of his ham > gear. John said that he would like to > be able to go to the Dayton Hamvention next year so he can > see many of his > friends. > > Our prayers are with John and his family as they go through > this difficult > time. If you know John and wish to contact him, his > email is > j...@flex-radio.com. > > Sincerely, > Gerald > > Gerald Youngblood, K5SDR > President > FlexRadio Systems > 13091 Pond Springs Rd. #250 > Austin, TX 78729 > Phone: 512-535-4713 > www.flex-radio.com > > "Tune in excitement!" (TM) > > > > > ___ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kc.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > Message delivered to k1...@yahoo.com > ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
[Flexradio] FLEX 5000A Possible PTT Issues when using WINMOOR
I am using the FLEX 5000A for WINMOOR and have had no problems establishing communications; however, I have had troubles passing messages. I have received the following comments from two different stations: 10/04 00:15 W9ON - sounds like a PTT problem on your transmission - first part of PSK signal cutting out 10/03 23:43 w9on - lots of "Sumcheck Fail" on your ACKs I am using a DELL Slim Studio with core 2 QUAD CPU Q8300 @2.5GHz OS: 64-bit VISTA USING VAC for audio com0com 2.2.1.0-x64 Power SDR PTT enable port 17 with RTS and DTR enabled WINMOOR SETUP: PTT PORT 7 RTS and DTRchecked PTT Baud Rate 4800 I have attached my debug log. Allen, W9ON ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] Broke it....
I have the correct firmware, and I just loaded psdr 1.18.2 and it works! Brett - Original Message - From: "Bret Mills" To: "'Brett Gazdzinski'" ; "'Tim Ellison'" ; "'FireBrick'" ; "'flex-Radio E-Mail Reflector'" Sent: Saturday, October 03, 2009 6:41 PM Subject: RE: [Flexradio] Broke it Which firmware do you have loaded to the Radio? If it is Firmware 2.0.0.0 PowerSDR 1.18.3 WILL NOT WORK with this firmware version. You should be using 1.3.0.8 on the Flex-5000 and Flex 1.2.5.6 on the Flex-3000. I am sure you have tried this BUT maybe not, the symptoms you have described would fit this issue. 73's Bret WX7Y -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski Sent: Saturday, October 03, 2009 3:20 PM To: Tim Ellison; FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it Yes, the radio shows up in the driver Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:48 PM Subject: Re: [Flexradio] Broke it Brett, If you are in demo mode when PowerSDR starts, then the problem is that the radio and the PC are not communicating with each other at the Firewire level. You have to resolve this first. So to do this, lets start with a clean slate because it might be impossible to figure out what is actually causing the problem. Do these steps and do not take any short cuts. 1.) Turn off the FLEX-5000 and remove the power from it (this results in a hardware reset) 2.) Using the Control Panel "Add and Remove Programs" or what ever they call in in your version of Windows, uninstall the FLEX Firewire driver. 3.) Reboot the PC - do not power up the radio. 4.) install the latest Firewire driver (http://support.flex-radio.com/Downloads.aspx?id=292) using the directions in the KB to the letter (http://kc.flex-radio.com/KnowledgebaseArticle50137.aspx). Make sure you reboot when indicated and also make sure the PC is completely up before powering on the FLEX-x000 to finish the driver installation. 5.) In the referenced article above, do step 14 to validate that the radio is communicating with the PC. 6.) If PowerSDR 1.18.3 is installed, un-install it using the Control Panel "Add and Remove Programs" applet. 7.) Delete the folder c:\Program Files\FlexRadio Systems\PowerSDR v1.18.3 to make sure the old database is not retained. 8.) Install a fresh copy of PowerSDR 1.18.3 (http://support.flex-radio.com/Downloads.aspx?id=294) 9.) After it is installed run the setup wizard and you should see the wisdom file creation dialog box. After the wisdom file is created, it should ask you what radio you are using after a few warning popups. Select the FLEX-5000. 10.) When you start PowerSDR again after the setup wizard is done, you should see the program creating a EEPROM backup and then it will transfer EEPROM data into the database. If you do not see this happening or it takes a long time, then there is something wring with the communication between the radio and the PC. And we have to figure out what that is before proceeding. -Tim -Original Message- From: Brett Gazdzinski [mailto:brett.gazdzin...@verizon.net] Sent: Saturday, October 03, 2009 1:33 PM To: Tim Ellison; FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it I reset the data base by going into demo mode, after it fails during int hardware. After the data base reset, I get error opening radio driver... Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:22 PM Subject: RE: [Flexradio] Broke it Do a database reset from the Setup form. If you are not presented to select the correct radio when PowerSDR is re-started, then you may have a driver problem. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski Sent: Saturday, October 03, 2009 1:19 PM To: FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it Psdr 1.18.3, firmware updated ok, driver version 3.4.2.6300, all the latest stuff, while I can update the radio firmware, when I open psdr it does not see the radio...only gives my sound card options, the driver does list the 5000. Brett - Original Message - From: "FireBrick" To: "Brett Gazdzinski" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:01 PM Subject: Re: [Flexradio] Broke it Brett Which version of PWSDR are you trying to start? Do you have the correct Driver installed. While the Driver should work for all versions. Did you remove it? The Firmware is version dependent. Did you remove the Firmware, and if so did you reinstall the correct Firmware version appropriate to the PWSDR version your t
[Flexradio] HEIL HM5 WITH FLEX CABLE
I have For Sale, Brand new, Never used!! Heil HM-5 Microphone. Flex 5000 cable. Microphone stand. Paid $132.50 plus shipping. Will sell for $80.00 Shipping: $20.00 Total: $100.00 Photo is available upon request. Sherman W2FLA Woodbourne, NY ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] Broke it....
Which firmware do you have loaded to the Radio? If it is Firmware 2.0.0.0 PowerSDR 1.18.3 WILL NOT WORK with this firmware version. You should be using 1.3.0.8 on the Flex-5000 and Flex 1.2.5.6 on the Flex-3000. I am sure you have tried this BUT maybe not, the symptoms you have described would fit this issue. 73's Bret WX7Y -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski Sent: Saturday, October 03, 2009 3:20 PM To: Tim Ellison; FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it Yes, the radio shows up in the driver Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:48 PM Subject: Re: [Flexradio] Broke it > Brett, > > If you are in demo mode when PowerSDR starts, then the problem is that the > radio and the PC are not communicating with each other at the Firewire > level. You have to resolve this first. > > So to do this, lets start with a clean slate because it might be > impossible to figure out what is actually causing the problem. Do these > steps and do not take any short cuts. > > 1.) Turn off the FLEX-5000 and remove the power from it (this results in a > hardware reset) > 2.) Using the Control Panel "Add and Remove Programs" or what ever they > call in in your version of Windows, uninstall the FLEX Firewire driver. > 3.) Reboot the PC - do not power up the radio. > 4.) install the latest Firewire driver > (http://support.flex-radio.com/Downloads.aspx?id=292) using the directions > in the KB to the letter > (http://kc.flex-radio.com/KnowledgebaseArticle50137.aspx). Make sure you > reboot when indicated and also make sure the PC is completely up before > powering on the FLEX-x000 to finish the driver installation. > 5.) In the referenced article above, do step 14 to validate that the radio > is communicating with the PC. > 6.) If PowerSDR 1.18.3 is installed, un-install it using the Control Panel > "Add and Remove Programs" applet. > 7.) Delete the folder c:\Program Files\FlexRadio Systems\PowerSDR v1.18.3 > to make sure the old database is not retained. > 8.) Install a fresh copy of PowerSDR 1.18.3 > (http://support.flex-radio.com/Downloads.aspx?id=294) > 9.) After it is installed run the setup wizard and you should see the > wisdom file creation dialog box. After the wisdom file is created, it > should ask you what radio you are using after a few warning popups. > Select the FLEX-5000. > 10.) When you start PowerSDR again after the setup wizard is done, you > should see the program creating a EEPROM backup and then it will transfer > EEPROM data into the database. If you do not see this happening or it > takes a long time, then there is something wring with the communication > between the radio and the PC. And we have to figure out what that is > before proceeding. > > > > -Tim > > -Original Message- > From: Brett Gazdzinski [mailto:brett.gazdzin...@verizon.net] > Sent: Saturday, October 03, 2009 1:33 PM > To: Tim Ellison; FireBrick; flex-Radio E-Mail Reflector > Subject: Re: [Flexradio] Broke it > > I reset the data base by going into demo mode, after it fails during int > hardware. > After the data base reset, I get error opening radio driver... > > Brett > > - Original Message - > From: "Tim Ellison" > To: "Brett Gazdzinski" ; "FireBrick" > ; "flex-Radio E-Mail Reflector" > > Sent: Saturday, October 03, 2009 1:22 PM > Subject: RE: [Flexradio] Broke it > > > Do a database reset from the Setup form. If you are not presented to > select > the correct radio when PowerSDR is re-started, then you may have a driver > problem. > > > > -Tim > > -Original Message- > From: flexradio-boun...@flex-radio.biz > [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski > Sent: Saturday, October 03, 2009 1:19 PM > To: FireBrick; flex-Radio E-Mail Reflector > Subject: Re: [Flexradio] Broke it > > Psdr 1.18.3, firmware updated ok, driver version 3.4.2.6300, all the > latest > stuff, while I can update the radio firmware, when I open psdr it does not > see the radio...only gives my sound card options, the driver does list the > 5000. > > Brett > > - Original Message - > From: "FireBrick" > To: "Brett Gazdzinski" ; "flex-Radio E-Mail > Reflector" > Sent: Saturday, October 03, 2009 1:01 PM > Subject: Re: [Flexradio] Broke it > > >> Brett >> Which version of PWSDR are you trying to start? >> >> Do you have the correct Driver installed. >> While the Driver should work for all versions. >> Did you remove it? >> >> The Firmware is version dependent. >> Did you remove the Firmware, and if so did you reinstall the correct >> Firmware version appropriate to the PWSDR version your trying to start. >> >> >> -- >> Resistance is assimil
Re: [Flexradio] Broke it....
Yes, the radio shows up in the driver Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:48 PM Subject: Re: [Flexradio] Broke it Brett, If you are in demo mode when PowerSDR starts, then the problem is that the radio and the PC are not communicating with each other at the Firewire level. You have to resolve this first. So to do this, lets start with a clean slate because it might be impossible to figure out what is actually causing the problem. Do these steps and do not take any short cuts. 1.) Turn off the FLEX-5000 and remove the power from it (this results in a hardware reset) 2.) Using the Control Panel "Add and Remove Programs" or what ever they call in in your version of Windows, uninstall the FLEX Firewire driver. 3.) Reboot the PC - do not power up the radio. 4.) install the latest Firewire driver (http://support.flex-radio.com/Downloads.aspx?id=292) using the directions in the KB to the letter (http://kc.flex-radio.com/KnowledgebaseArticle50137.aspx). Make sure you reboot when indicated and also make sure the PC is completely up before powering on the FLEX-x000 to finish the driver installation. 5.) In the referenced article above, do step 14 to validate that the radio is communicating with the PC. 6.) If PowerSDR 1.18.3 is installed, un-install it using the Control Panel "Add and Remove Programs" applet. 7.) Delete the folder c:\Program Files\FlexRadio Systems\PowerSDR v1.18.3 to make sure the old database is not retained. 8.) Install a fresh copy of PowerSDR 1.18.3 (http://support.flex-radio.com/Downloads.aspx?id=294) 9.) After it is installed run the setup wizard and you should see the wisdom file creation dialog box. After the wisdom file is created, it should ask you what radio you are using after a few warning popups. Select the FLEX-5000. 10.) When you start PowerSDR again after the setup wizard is done, you should see the program creating a EEPROM backup and then it will transfer EEPROM data into the database. If you do not see this happening or it takes a long time, then there is something wring with the communication between the radio and the PC. And we have to figure out what that is before proceeding. -Tim -Original Message- From: Brett Gazdzinski [mailto:brett.gazdzin...@verizon.net] Sent: Saturday, October 03, 2009 1:33 PM To: Tim Ellison; FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it I reset the data base by going into demo mode, after it fails during int hardware. After the data base reset, I get error opening radio driver... Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:22 PM Subject: RE: [Flexradio] Broke it Do a database reset from the Setup form. If you are not presented to select the correct radio when PowerSDR is re-started, then you may have a driver problem. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski Sent: Saturday, October 03, 2009 1:19 PM To: FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it Psdr 1.18.3, firmware updated ok, driver version 3.4.2.6300, all the latest stuff, while I can update the radio firmware, when I open psdr it does not see the radio...only gives my sound card options, the driver does list the 5000. Brett - Original Message - From: "FireBrick" To: "Brett Gazdzinski" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:01 PM Subject: Re: [Flexradio] Broke it Brett Which version of PWSDR are you trying to start? Do you have the correct Driver installed. While the Driver should work for all versions. Did you remove it? The Firmware is version dependent. Did you remove the Firmware, and if so did you reinstall the correct Firmware version appropriate to the PWSDR version your trying to start. -- Resistance is assimilated. Prepare to be futile. Waitaminute. -- TOWER/WEBCAMS and Weather Page @ http://hhweather.webhop.org - Original Message - From: "Brett Gazdzinski" To: "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 11:54 AM Subject: [Flexradio] Broke it In an effort to go back to the default config, and also try older versions of Psdr, I now cant get the radio to work at all. It does not seem to communicate with the PC and wants to go into demo mode. Funny (sort of) when I did not have the radio, demo would not work, now that I have the radio, demo is all I can now get to work I have removed everything and reinstalled, but that does not seem to erase the device driver or something... When I power on the 50
[Flexradio] anyone useing PWSDR
I'm looking for someone using a computer sound card for digital modes with PWSDR. I know someone told me that's what they do but I forgot who it was. which is not unusual as I seem to forget a lot of things lately. :-( -- I'm at the corner of Walk and Don't Walk... -- TOWER/WEBCAMS and Weather Page @ http://hhweather.webhop.org ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] Broke it....
What about step #5 listed below? Do you see the radio in the FLEX Firewire control panel? -Tim -Original Message- From: Brett Gazdzinski [mailto:brett.gazdzin...@verizon.net] Sent: Saturday, October 03, 2009 2:14 PM To: Tim Ellison; FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it I did this just like you said, and I get error opening radio driver. When I power on the flex, I do get the two beeps (like normal). The 2nd time I open psdr I get the demo mode and it shows under hardware config a 5000 but with the s/n all zeros Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:48 PM Subject: Re: [Flexradio] Broke it > Brett, > > If you are in demo mode when PowerSDR starts, then the problem is that the > radio and the PC are not communicating with each other at the Firewire > level. You have to resolve this first. > > So to do this, lets start with a clean slate because it might be > impossible to figure out what is actually causing the problem. Do these > steps and do not take any short cuts. > > 1.) Turn off the FLEX-5000 and remove the power from it (this results in a > hardware reset) > 2.) Using the Control Panel "Add and Remove Programs" or what ever they > call in in your version of Windows, uninstall the FLEX Firewire driver. > 3.) Reboot the PC - do not power up the radio. > 4.) install the latest Firewire driver > (http://support.flex-radio.com/Downloads.aspx?id=292) using the directions > in the KB to the letter > (http://kc.flex-radio.com/KnowledgebaseArticle50137.aspx). Make sure you > reboot when indicated and also make sure the PC is completely up before > powering on the FLEX-x000 to finish the driver installation. > 5.) In the referenced article above, do step 14 to validate that the radio > is communicating with the PC. > 6.) If PowerSDR 1.18.3 is installed, un-install it using the Control Panel > "Add and Remove Programs" applet. > 7.) Delete the folder c:\Program Files\FlexRadio Systems\PowerSDR v1.18.3 > to make sure the old database is not retained. > 8.) Install a fresh copy of PowerSDR 1.18.3 > (http://support.flex-radio.com/Downloads.aspx?id=294) > 9.) After it is installed run the setup wizard and you should see the > wisdom file creation dialog box. After the wisdom file is created, it > should ask you what radio you are using after a few warning popups. > Select the FLEX-5000. > 10.) When you start PowerSDR again after the setup wizard is done, you > should see the program creating a EEPROM backup and then it will transfer > EEPROM data into the database. If you do not see this happening or it > takes a long time, then there is something wring with the communication > between the radio and the PC. And we have to figure out what that is > before proceeding. > > > > -Tim > > -Original Message- > From: Brett Gazdzinski [mailto:brett.gazdzin...@verizon.net] > Sent: Saturday, October 03, 2009 1:33 PM > To: Tim Ellison; FireBrick; flex-Radio E-Mail Reflector > Subject: Re: [Flexradio] Broke it > > I reset the data base by going into demo mode, after it fails during int > hardware. > After the data base reset, I get error opening radio driver... > > Brett > > - Original Message - > From: "Tim Ellison" > To: "Brett Gazdzinski" ; "FireBrick" > ; "flex-Radio E-Mail Reflector" > > Sent: Saturday, October 03, 2009 1:22 PM > Subject: RE: [Flexradio] Broke it > > > Do a database reset from the Setup form. If you are not presented to > select > the correct radio when PowerSDR is re-started, then you may have a driver > problem. > > > > -Tim > > -Original Message- > From: flexradio-boun...@flex-radio.biz > [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski > Sent: Saturday, October 03, 2009 1:19 PM > To: FireBrick; flex-Radio E-Mail Reflector > Subject: Re: [Flexradio] Broke it > > Psdr 1.18.3, firmware updated ok, driver version 3.4.2.6300, all the > latest > stuff, while I can update the radio firmware, when I open psdr it does not > see the radio...only gives my sound card options, the driver does list the > 5000. > > Brett > > - Original Message - > From: "FireBrick" > To: "Brett Gazdzinski" ; "flex-Radio E-Mail > Reflector" > Sent: Saturday, October 03, 2009 1:01 PM > Subject: Re: [Flexradio] Broke it > > >> Brett >> Which version of PWSDR are you trying to start? >> >> Do you have the correct Driver installed. >> While the Driver should work for all versions. >> Did you remove it? >> >> The Firmware is version dependent. >> Did you remove the Firmware, and if so did you reinstall the correct >> Firmware version appropriate to the PWSDR version your trying to start. >> >> >> -- >> Resistance is assimilated. Prepare to be futile. Waitaminute. >> -
Re: [Flexradio] Broke it....
I did this just like you said, and I get error opening radio driver. When I power on the flex, I do get the two beeps (like normal). The 2nd time I open psdr I get the demo mode and it shows under hardware config a 5000 but with the s/n all zeros Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:48 PM Subject: Re: [Flexradio] Broke it Brett, If you are in demo mode when PowerSDR starts, then the problem is that the radio and the PC are not communicating with each other at the Firewire level. You have to resolve this first. So to do this, lets start with a clean slate because it might be impossible to figure out what is actually causing the problem. Do these steps and do not take any short cuts. 1.) Turn off the FLEX-5000 and remove the power from it (this results in a hardware reset) 2.) Using the Control Panel "Add and Remove Programs" or what ever they call in in your version of Windows, uninstall the FLEX Firewire driver. 3.) Reboot the PC - do not power up the radio. 4.) install the latest Firewire driver (http://support.flex-radio.com/Downloads.aspx?id=292) using the directions in the KB to the letter (http://kc.flex-radio.com/KnowledgebaseArticle50137.aspx). Make sure you reboot when indicated and also make sure the PC is completely up before powering on the FLEX-x000 to finish the driver installation. 5.) In the referenced article above, do step 14 to validate that the radio is communicating with the PC. 6.) If PowerSDR 1.18.3 is installed, un-install it using the Control Panel "Add and Remove Programs" applet. 7.) Delete the folder c:\Program Files\FlexRadio Systems\PowerSDR v1.18.3 to make sure the old database is not retained. 8.) Install a fresh copy of PowerSDR 1.18.3 (http://support.flex-radio.com/Downloads.aspx?id=294) 9.) After it is installed run the setup wizard and you should see the wisdom file creation dialog box. After the wisdom file is created, it should ask you what radio you are using after a few warning popups. Select the FLEX-5000. 10.) When you start PowerSDR again after the setup wizard is done, you should see the program creating a EEPROM backup and then it will transfer EEPROM data into the database. If you do not see this happening or it takes a long time, then there is something wring with the communication between the radio and the PC. And we have to figure out what that is before proceeding. -Tim -Original Message- From: Brett Gazdzinski [mailto:brett.gazdzin...@verizon.net] Sent: Saturday, October 03, 2009 1:33 PM To: Tim Ellison; FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it I reset the data base by going into demo mode, after it fails during int hardware. After the data base reset, I get error opening radio driver... Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:22 PM Subject: RE: [Flexradio] Broke it Do a database reset from the Setup form. If you are not presented to select the correct radio when PowerSDR is re-started, then you may have a driver problem. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski Sent: Saturday, October 03, 2009 1:19 PM To: FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it Psdr 1.18.3, firmware updated ok, driver version 3.4.2.6300, all the latest stuff, while I can update the radio firmware, when I open psdr it does not see the radio...only gives my sound card options, the driver does list the 5000. Brett - Original Message - From: "FireBrick" To: "Brett Gazdzinski" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:01 PM Subject: Re: [Flexradio] Broke it Brett Which version of PWSDR are you trying to start? Do you have the correct Driver installed. While the Driver should work for all versions. Did you remove it? The Firmware is version dependent. Did you remove the Firmware, and if so did you reinstall the correct Firmware version appropriate to the PWSDR version your trying to start. -- Resistance is assimilated. Prepare to be futile. Waitaminute. -- TOWER/WEBCAMS and Weather Page @ http://hhweather.webhop.org - Original Message - From: "Brett Gazdzinski" To: "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 11:54 AM Subject: [Flexradio] Broke it In an effort to go back to the default config, and also try older versions of Psdr, I now cant get the radio to work at all. It does not seem to communicate with the PC and wants to go into demo mode. Funny (sort of) when I did not have the radio, demo w
Re: [Flexradio] Broke it....
Brett, If you are in demo mode when PowerSDR starts, then the problem is that the radio and the PC are not communicating with each other at the Firewire level. You have to resolve this first. So to do this, lets start with a clean slate because it might be impossible to figure out what is actually causing the problem. Do these steps and do not take any short cuts. 1.) Turn off the FLEX-5000 and remove the power from it (this results in a hardware reset) 2.) Using the Control Panel "Add and Remove Programs" or what ever they call in in your version of Windows, uninstall the FLEX Firewire driver. 3.) Reboot the PC - do not power up the radio. 4.) install the latest Firewire driver (http://support.flex-radio.com/Downloads.aspx?id=292) using the directions in the KB to the letter (http://kc.flex-radio.com/KnowledgebaseArticle50137.aspx). Make sure you reboot when indicated and also make sure the PC is completely up before powering on the FLEX-x000 to finish the driver installation. 5.) In the referenced article above, do step 14 to validate that the radio is communicating with the PC. 6.) If PowerSDR 1.18.3 is installed, un-install it using the Control Panel "Add and Remove Programs" applet. 7.) Delete the folder c:\Program Files\FlexRadio Systems\PowerSDR v1.18.3 to make sure the old database is not retained. 8.) Install a fresh copy of PowerSDR 1.18.3 (http://support.flex-radio.com/Downloads.aspx?id=294) 9.) After it is installed run the setup wizard and you should see the wisdom file creation dialog box. After the wisdom file is created, it should ask you what radio you are using after a few warning popups. Select the FLEX-5000. 10.) When you start PowerSDR again after the setup wizard is done, you should see the program creating a EEPROM backup and then it will transfer EEPROM data into the database. If you do not see this happening or it takes a long time, then there is something wring with the communication between the radio and the PC. And we have to figure out what that is before proceeding. -Tim -Original Message- From: Brett Gazdzinski [mailto:brett.gazdzin...@verizon.net] Sent: Saturday, October 03, 2009 1:33 PM To: Tim Ellison; FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it I reset the data base by going into demo mode, after it fails during int hardware. After the data base reset, I get error opening radio driver... Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:22 PM Subject: RE: [Flexradio] Broke it Do a database reset from the Setup form. If you are not presented to select the correct radio when PowerSDR is re-started, then you may have a driver problem. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski Sent: Saturday, October 03, 2009 1:19 PM To: FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it Psdr 1.18.3, firmware updated ok, driver version 3.4.2.6300, all the latest stuff, while I can update the radio firmware, when I open psdr it does not see the radio...only gives my sound card options, the driver does list the 5000. Brett - Original Message - From: "FireBrick" To: "Brett Gazdzinski" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:01 PM Subject: Re: [Flexradio] Broke it > Brett > Which version of PWSDR are you trying to start? > > Do you have the correct Driver installed. > While the Driver should work for all versions. > Did you remove it? > > The Firmware is version dependent. > Did you remove the Firmware, and if so did you reinstall the correct > Firmware version appropriate to the PWSDR version your trying to start. > > > -- > Resistance is assimilated. Prepare to be futile. Waitaminute. > -- > TOWER/WEBCAMS and Weather Page > @ http://hhweather.webhop.org > > - Original Message - > From: "Brett Gazdzinski" > To: "flex-Radio E-Mail Reflector" > Sent: Saturday, October 03, 2009 11:54 AM > Subject: [Flexradio] Broke it > > >> In an effort to go back to the default config, and also try older >> versions of Psdr, I now cant get the radio to work at all. >> It does not seem to communicate with the PC and wants to go into demo >> mode. >> >> Funny (sort of) when I did not have the radio, demo would not work, >> now that I have the radio, demo is all I can now get to work >> >> I have removed everything and reinstalled, but that does not seem to >> erase the device driver or something... >> >> When I power on the 5000, I get two beeps like normal, open psdr and >> it says it cant communicate with the radio. >> >> I have tried deleting the database files, still no go. >> Anyone got any ideas? >> >
Re: [Flexradio] Broke it....
I reset the data base by going into demo mode, after it fails during int hardware. After the data base reset, I get error opening radio driver... Brett - Original Message - From: "Tim Ellison" To: "Brett Gazdzinski" ; "FireBrick" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:22 PM Subject: RE: [Flexradio] Broke it Do a database reset from the Setup form. If you are not presented to select the correct radio when PowerSDR is re-started, then you may have a driver problem. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski Sent: Saturday, October 03, 2009 1:19 PM To: FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it Psdr 1.18.3, firmware updated ok, driver version 3.4.2.6300, all the latest stuff, while I can update the radio firmware, when I open psdr it does not see the radio...only gives my sound card options, the driver does list the 5000. Brett - Original Message - From: "FireBrick" To: "Brett Gazdzinski" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:01 PM Subject: Re: [Flexradio] Broke it Brett Which version of PWSDR are you trying to start? Do you have the correct Driver installed. While the Driver should work for all versions. Did you remove it? The Firmware is version dependent. Did you remove the Firmware, and if so did you reinstall the correct Firmware version appropriate to the PWSDR version your trying to start. -- Resistance is assimilated. Prepare to be futile. Waitaminute. -- TOWER/WEBCAMS and Weather Page @ http://hhweather.webhop.org - Original Message - From: "Brett Gazdzinski" To: "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 11:54 AM Subject: [Flexradio] Broke it In an effort to go back to the default config, and also try older versions of Psdr, I now cant get the radio to work at all. It does not seem to communicate with the PC and wants to go into demo mode. Funny (sort of) when I did not have the radio, demo would not work, now that I have the radio, demo is all I can now get to work I have removed everything and reinstalled, but that does not seem to erase the device driver or something... When I power on the 5000, I get two beeps like normal, open psdr and it says it cant communicate with the radio. I have tried deleting the database files, still no go. Anyone got any ideas? Thanks, Brett ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to w...@billnjudy.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to telli...@itsco.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] Broke it....
Do a database reset from the Setup form. If you are not presented to select the correct radio when PowerSDR is re-started, then you may have a driver problem. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Brett Gazdzinski Sent: Saturday, October 03, 2009 1:19 PM To: FireBrick; flex-Radio E-Mail Reflector Subject: Re: [Flexradio] Broke it Psdr 1.18.3, firmware updated ok, driver version 3.4.2.6300, all the latest stuff, while I can update the radio firmware, when I open psdr it does not see the radio...only gives my sound card options, the driver does list the 5000. Brett - Original Message - From: "FireBrick" To: "Brett Gazdzinski" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:01 PM Subject: Re: [Flexradio] Broke it > Brett > Which version of PWSDR are you trying to start? > > Do you have the correct Driver installed. > While the Driver should work for all versions. > Did you remove it? > > The Firmware is version dependent. > Did you remove the Firmware, and if so did you reinstall the correct > Firmware version appropriate to the PWSDR version your trying to start. > > > -- > Resistance is assimilated. Prepare to be futile. Waitaminute. > -- > TOWER/WEBCAMS and Weather Page > @ http://hhweather.webhop.org > > - Original Message - > From: "Brett Gazdzinski" > To: "flex-Radio E-Mail Reflector" > Sent: Saturday, October 03, 2009 11:54 AM > Subject: [Flexradio] Broke it > > >> In an effort to go back to the default config, and also try older >> versions of Psdr, I now cant get the radio to work at all. >> It does not seem to communicate with the PC and wants to go into demo >> mode. >> >> Funny (sort of) when I did not have the radio, demo would not work, >> now that I have the radio, demo is all I can now get to work >> >> I have removed everything and reinstalled, but that does not seem to >> erase the device driver or something... >> >> When I power on the 5000, I get two beeps like normal, open psdr and >> it says it cant communicate with the radio. >> >> I have tried deleting the database files, still no go. >> Anyone got any ideas? >> >> Thanks, >> Brett >> >> >> ___ >> FlexRadio Systems Mailing List >> FlexRadio@flex-radio.biz >> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz >> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ >> Knowledge Base: http://kc.flex-radio.com/ Homepage: >> http://www.flex-radio.com/ >> Message delivered to w...@billnjudy.com > ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to telli...@itsco.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] Broke it....
Psdr 1.18.3, firmware updated ok, driver version 3.4.2.6300, all the latest stuff, while I can update the radio firmware, when I open psdr it does not see the radio...only gives my sound card options, the driver does list the 5000. Brett - Original Message - From: "FireBrick" To: "Brett Gazdzinski" ; "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 1:01 PM Subject: Re: [Flexradio] Broke it Brett Which version of PWSDR are you trying to start? Do you have the correct Driver installed. While the Driver should work for all versions. Did you remove it? The Firmware is version dependent. Did you remove the Firmware, and if so did you reinstall the correct Firmware version appropriate to the PWSDR version your trying to start. -- Resistance is assimilated. Prepare to be futile. Waitaminute. -- TOWER/WEBCAMS and Weather Page @ http://hhweather.webhop.org - Original Message - From: "Brett Gazdzinski" To: "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 11:54 AM Subject: [Flexradio] Broke it In an effort to go back to the default config, and also try older versions of Psdr, I now cant get the radio to work at all. It does not seem to communicate with the PC and wants to go into demo mode. Funny (sort of) when I did not have the radio, demo would not work, now that I have the radio, demo is all I can now get to work I have removed everything and reinstalled, but that does not seem to erase the device driver or something... When I power on the 5000, I get two beeps like normal, open psdr and it says it cant communicate with the radio. I have tried deleting the database files, still no go. Anyone got any ideas? Thanks, Brett ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to w...@billnjudy.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] Broke it....
Brett Which version of PWSDR are you trying to start? Do you have the correct Driver installed. While the Driver should work for all versions. Did you remove it? The Firmware is version dependent. Did you remove the Firmware, and if so did you reinstall the correct Firmware version appropriate to the PWSDR version your trying to start. -- Resistance is assimilated. Prepare to be futile. Waitaminute. -- TOWER/WEBCAMS and Weather Page @ http://hhweather.webhop.org - Original Message - From: "Brett Gazdzinski" To: "flex-Radio E-Mail Reflector" Sent: Saturday, October 03, 2009 11:54 AM Subject: [Flexradio] Broke it In an effort to go back to the default config, and also try older versions of Psdr, I now cant get the radio to work at all. It does not seem to communicate with the PC and wants to go into demo mode. Funny (sort of) when I did not have the radio, demo would not work, now that I have the radio, demo is all I can now get to work I have removed everything and reinstalled, but that does not seem to erase the device driver or something... When I power on the 5000, I get two beeps like normal, open psdr and it says it cant communicate with the radio. I have tried deleting the database files, still no go. Anyone got any ideas? Thanks, Brett ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to w...@billnjudy.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
Re: [Flexradio] flex 5000a +i mac 2.93
2. flex 5000a +i mac 2.93 (elan paim) hello is any one out there use the? I-?Mac+ flex 5000a ? i know about[ boot camp]how the FLEX 5000A working with the i mac the new i mac i think support fire wire of 400 to 800 . any problem with this combo ? i ask this before i will buy the i mac . i thank you all for your great support Elan g0uut/dl9fcc E&T Paim -- Good day, Elan; I share your apprehension in making a Mac work with a Flex-Radio and PowerSDR. For me, it was a difficult task, simply because I had chosen the incorrect Firewire device to disable in my XP operating environment. I had followed a proceedure on the Flex-Radio KB (knowledge base), but the words in the original proceedure were different (did not match what was seen in the DEVICE MANAGER) to the point that I wasted a lot of days and hours, before I accidentally discovered the correct method. I had since contacted the originator of the Boot Camp install that would allow PowerSDR and the like to function on a Mac. I had offered the changes to this otherwise excellent document; -As yet, I do not see any modification or update, so I will simply copy the text of the now-modified proceedure below. I do hope that this will be of help to you. (Using this modified proceedure, I have been successful in installing the needed drivers and PowerSDR on two iMacs and one MacBook Pro.) 73! -Mike- KOJTA === How to Install PowerSDR 1.x on an Intel Macintosh System Dependencies Minimum PowerSDR Version: 1.18.1 Applicable Hardware: Any FLEX-xx00 SDR Content provided by: Brian, WB6RQN (brian HYPHEN wb6rqn AT lloyd DOT com) Modified by Mike, K0JTA (k0jta (at) arrl.net) on 9-28-09 Note: It helps to be familiar and comfortable with both the Macintosh OS-X and Windows XP operating systems. Recommended Hardware: 2.4 GHz Intel Core 2 Duo, 2GB 667 MHz DDR2 SDRAM, 160GB HD Recommended Software: Mac OS X 10.5.5 (Leopard) [install disk 1 or 2] Boot Camp 2.1 (or latest version) XP Home with SP2 Installation CD Service Pack 3 for Windows XP (SP3) - from Windows Update Microsoft .NET 1.1 Framework Microsoft .NET 3.5 SP 1 Framework FLEX Firewire device driver 3.4.0.5254 (or greater) FLEX-n000 SDR firmware update (latest version) PowerSDR 1.18.1 Installation program Recommended Documentation: Boot Camp Installation Guide ( http://manuals.info.apple.com/en_US/Boot_Camp_Install-Setup.pdf ) Installation Procedure: Step 1. Go to the Apple web site and download the Boot Camp Installation Guide. Step 2. Read the Boot Camp Installation Guide (It is best to PRINT the manual!) Step 3. Boot your Intel Mac then start Boot Camp Assistant. Step 4. Let Boot Camp partition the disk. Boot Camp Assistant will give you several options for partitioning your disk, including splitting it half-and-half between Windows and MacOS, making a 32GB Windows partition, or letting you pick what you need. If you are only going to use Boot Camp and the Windows Partition to run PowerSDR and some other ham radio things, e.g. Ham Radio Deluxe and a digital-mode program like FLdigi or DM780, you only need a few Gigabytes for your windows partition. I gave my windows partition 10GB and it was happy. Remember, you may need to leave enough room for Windows to do an upgrade to SP3 so there needs to be room for the SP3 installer to do a backup. Step 5. Let the Boot Camp Assistant start the Windows XP installation process. NOTE: You must use a WinXP SP2 (service pack 2) install CD. (You may also use an XP-Service Pack 3 installation disk.) Step 6. Go through the normal XP installation process. Select the new partition that was generated by Boot camp. Allow Windows to a quick format of partition "C: ... [FAT32] ...". Important: Remember you need to let Windows re-format the new partition even though Boot Camp formatted the partition as FAT32 when it created it! This is needed to ensure that Windows XP has a proper boot block in the partition. If you fail to do this, Windows will not reboot after the first phase of the Windows installation. Step 7. Install Windows XP-SP2. (Preferably XP-SP3!) The installation will restart the computer one time, during the installation process, so leave the XP installation CD in the Mac. Once Windows is completely installed and running, EJECT the Windows XP installation disk, and then insert the "MacOS X Install Disk 1" that came with your computer, and let it install all the drivers. (In some cases this will be MacOS X Install Disk-2, not disk-1; If the correct disk is in place, the Boot Camp drivers will be installed into the Windows environment; If there are no Boot Camp drivers on the disk, just eject the disk, and try the other one that came as standard equipment with your Mac computer.) Step 8. Download and install all the Apple MacOS X updates. -Do a search for {download "Windows XP Drivers Update" boot camp} as an example, to get a download link to get the ne
[Flexradio] Broke it....
In an effort to go back to the default config, and also try older versions of Psdr, I now cant get the radio to work at all. It does not seem to communicate with the PC and wants to go into demo mode. Funny (sort of) when I did not have the radio, demo would not work, now that I have the radio, demo is all I can now get to work I have removed everything and reinstalled, but that does not seem to erase the device driver or something... When I power on the 5000, I get two beeps like normal, open psdr and it says it cant communicate with the radio. I have tried deleting the database files, still no go. Anyone got any ideas? Thanks, Brett ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com
[Flexradio] Health news regarding John Basilotto, W5GI
Dear FlexRadio customers, Many of you know our friend and colleague, John Basilotto W5GI, who retired from FlexRadio a couple months ago due to an undiagnosed health problem. On Thursday, John came by the office to tell us that he has been diagnosed with pancreatic cancer. He plans to meet with an oncologist soon to see what treatment options he may have, if any. John has a great attitude and he plans to stay as active as he can, including on the air. In fact, he is at the Belton, Texas Hamfest this morning selling off a lot of his ham gear. John said that he would like to be able to go to the Dayton Hamvention next year so he can see many of his friends. Our prayers are with John and his family as they go through this difficult time. If you know John and wish to contact him, his email is j...@flex-radio.com. Sincerely, Gerald Gerald Youngblood, K5SDR President FlexRadio Systems 13091 Pond Springs Rd. #250 Austin, TX 78729 Phone: 512-535-4713 www.flex-radio.com "Tune in excitement!" (TM) ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flex-radio.com/ Homepage: http://www.flex-radio.com/ Message delivered to arch...@mail-archive.com