Re: [Flexradio] SSB is gone

2011-07-31 Thread Neal Campbell 
I sincerely am not  meaning to make fun of Greg but this is an example of my
method of problem analysis!

I always assume that the most expensive part in the chain is  the one that
is broken! Always!

8 years ago my ring rotor stopped turning. It was winter, I had been reading
somewhere stories of the ring rotor motors seizing up and I wasn't in great
shape so I just leapt to the conclusion one of the motors had locked up.
Ordered one and waited for warmer days. Finally Spring sprung and got out on
the tower to replace it. Had a hard time taking the old one out and since it
was bad, I damaged it in the extraction. Got the new one in and VOILA, it no
turn! Got the VOM out and discovered that one lead in the telephone wire I
had strung to control the rotor from inside the house had broken.
Approximately $3 of wire. Now I had a new motor, a damaged old motor and
needed a story to tell "the boyz" that didn't make me look like the idiot I
am!

Sri, just had to relate my story!

73
Neal

On Sun, Jul 31, 2011 at 7:16 PM, Greg  wrote:

> Never mind.
>
> Faulty SO2R switch...
>
>
>
>
> On 7/31/2011 4:11 PM, Greg wrote:
>
>> I had already updated to PSDR 2.1.5 and it has been working OK here.  This
>> morning I was listening to my regular swap net but did not check in since I
>> had some work to do outside.
>>
>> Went to work some DX this afternoon and I have no audio output.  CW is
>> working fine.  I have the mixer set correctly to the FP mic input but just
>> no output at all.
>>
>> Any ideas out there?
>>
>> Thanks
>> Greg
>>
>>
>>
> __**_
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/**mailman/listinfo/flexradio_**flex-radio.biz
> Archives: 
> http://www.mail-archive.com/**flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/
>



-- 
Abroham Neal Software
www.abrohamnealsoftware.com
Work:(540) 645 5394
Mobile:(540) 645 8171
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] SSB is gone

2011-07-31 Thread Greg 

Never mind.

Faulty SO2R switch...



On 7/31/2011 4:11 PM, Greg wrote:
I had already updated to PSDR 2.1.5 and it has been working OK here.  
This morning I was listening to my regular swap net but did not check 
in since I had some work to do outside.


Went to work some DX this afternoon and I have no audio output.  CW is 
working fine.  I have the mixer set correctly to the FP mic input but 
just no output at all.


Any ideas out there?

Thanks
Greg




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] SSB is gone

2011-07-31 Thread Greg 
I had already updated to PSDR 2.1.5 and it has been working OK here.  
This morning I was listening to my regular swap net but did not check in 
since I had some work to do outside.


Went to work some DX this afternoon and I have no audio output.  CW is 
working fine.  I have the mixer set correctly to the FP mic input but 
just no output at all.


Any ideas out there?

Thanks
Greg



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Memory form select not working properly

2011-07-31 Thread Tim Ellison, W4TME 

OK.  Now I understand.  Thanks for the clarification.

That enhancement request for RX2 support in the memory form has already 
need entered into the database for future considerations.


Tim Ellison, W4TME
Internet Systems Admin. & Customer Support Engineer
FlexRadio Systems^(TM)
4616 W Howard Ln Ste 1-150
Austin, TX 78728
Phone: 512-535-4713 Ext. 223
Email: t...@flexradio.com 
Web: www.flexradio.com 

logo
/Tune In Excitement^(TM)
PowerSDR^(TM) is a trademark of FlexRadio Systems/


On 7/31/2011 2:37 PM, John Vandenberg wrote:
It means for me that I cannot make use of the panel since I have to 
use V/U on RX2.
(RX1 is the only receiver that will work with VAC for my digital 
programs) 


May be a collum could be added on the memory form specifying the 
receiver RX1/RX2?


John, ve3dvv 

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Memory form select not working properly

2011-07-31 Thread John Vandenberg 

> Although I do not fully understand your statement "Since I use RX1 with

VAC for digital stuff I am out of luck!"  Can you explain this in more
detail?


It means for me that I cannot make use of the panel since I have to use V/U 
on RX2.

(RX1 is the only receiver that will work with VAC for my digital programs)

May be a collum could be added on the memory form specifying the receiver 
RX1/RX2?


John, ve3dvv

--

Message: 3
Date: Sat, 30 Jul 2011 18:47:33 -0400
From: "John Vandenberg" 
To: 
Subject: [Flexradio] Memory form select not working properly
Message-ID: 
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original

The select gives an error when you are using RX2 for V/U. (cannot use UHF 
on

RX1+ UHF on RX2)
It seems to work only for RX1.  Since I use RX1 with VAC for digital stuff 
I

am out of luck!

Any plans on a fix so it will work for RX2 as well?

John, ve3dvv




--

Message: 4
Date: Sat, 30 Jul 2011 20:41:17 -0400
From: "Tim Ellison, W4TME" 
To: flexradio@flex-radio.biz
Subject: Re: [Flexradio] Memory form select not working properly
Message-ID: <4e34a4ad.1080...@flex-radio.com>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed

This is a consequence of the memories only updating RX1 and having RX2
on the same V/U band as the memory channel designation.

Although I do not fully understand your statement "Since I use RX1 with
VAC for digital stuff I am out of luck!"  Can you explain this in more
detail?

-Tim
---
Tim Ellison, W4TME
Internet Systems Admin. & Customer Support Engineer
FlexRadio Systems^(TM)
4616 W Howard Ln Ste 1-150
Austin, TX 78728
Phone: 512-535-4713 Ext. 223
Email: t...@flexradio.com 
Web: www.flexradio.com 

logo
/Tune In Excitement^(TM)
PowerSDR^(TM) is a trademark of FlexRadio Systems/


On 7/30/2011 6:47 PM, John Vandenberg wrote:

The select gives an error when you are using RX2 for V/U. (cannot use
UHF on RX1+ UHF on RX2)
It seems to work only for RX1.  Since I use RX1 with VAC for digital
stuff I am out of luck!

Any plans on a fix so it will work for RX2 as well?

John, ve3dvv




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] 32 watts 6m only

2011-07-31 Thread Tim Ellison, W4TME 
When you checked the other bands, were you using the same modulation 
method and output AF gain settings for the test?


If so, then you probably should contact Support (supp...@flexradio.com) 
and open a helpdesk ticket for further triage.  You may need a PA power 
calibration for 6m.


-Tim
---
Tim Ellison, W4TME
Internet Systems Admin. & Customer Support Engineer
FlexRadio Systems^(TM)
4616 W Howard Ln Ste 1-150
Austin, TX 78728
Phone: 512-535-4713 Ext. 223
Email: t...@flexradio.com 
Web: www.flexradio.com 

logo
/Tune In Excitement^(TM)
PowerSDR^(TM) is a trademark of FlexRadio Systems/


On 7/31/2011 1:10 PM, Ed Stallman wrote:
Need a little help here, this morning I was working WSJT 441 mode on  
6m . I had the Flex 5000a set to 75 watts . All qso's were going 
pretty fast so I wasn't TXing very long . I was making another call 
when I looked and the F5K was only doing Like 10 watts .. Thinking the 
radio was hot I stopped TXing waited 15 minutes and now the radio does 
32 watts .. I checked on other bands 80m and 20m , both doing 100 
watts there,, I have connected Dummy load to So2393 , 2 and 1  and 
also changing the antenna port under the antenna menu but  32 watts is 
it on 6m only!


any idea ?

Thanks Ed


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: 
http://www.flexradio.com/

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] test ignore please

2011-07-31 Thread Kent Tiburski 
test

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] 32 watts 6m only

2011-07-31 Thread Ed Stallman 
Need a little help here, this morning I was working WSJT 441 mode 
on  6m . I had the Flex 5000a set to 75 watts . All qso's were going 
pretty fast so I wasn't TXing very long . I was making another call 
when I looked and the F5K was only doing Like 10 watts .. Thinking 
the radio was hot I stopped TXing waited 15 minutes and now the radio 
does 32 watts .. I checked on other bands 80m and 20m , both doing 
100 watts there,, I have connected Dummy load to So2393 , 2 and 
1  and also changing the antenna port under the antenna menu but  32 
watts is it on 6m only!


any idea ?

Thanks Ed


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] 2.1.5 firmware upgrade failure

2011-07-31 Thread Tim Ellison, W4TME 

Pete,

You should be OK if you do not get this error on subsequent restarts of 
the radio and PowerSDR.  If you encounter any strange problems, please 
drop us an e-mail at supp...@flexradio.com so we can open a ticket and 
investigate further.


-Tim
---
Tim Ellison, W4TME
Internet Systems Admin. & Customer Support Engineer
FlexRadio Systems^(TM)
4616 W Howard Ln Ste 1-150
Austin, TX 78728
Phone: 512-535-4713 Ext. 223
Email: t...@flexradio.com 
Web: www.flexradio.com 

logo
/Tune In Excitement^(TM)
PowerSDR^(TM) is a trademark of FlexRadio Systems/


On 7/31/2011 12:56 AM, pbour...@w6op.com wrote:

I just upgraded my Flex 3000 from 2.0.22 to 2.1.5 PowerSDR. I rebooted to
make sure the PC was clean, installed PowerSDR 2.1.5 and rebooted again.
When I powered up the Flex 3000 it went through the usual stuff like a new
radio. Then it said I needed a firmware upgrade which I agreed to. The
firmware upgrade seemed to go fine and then I got a dialog box with a
caption of;



"Fatal Error" External component has thrown an exception.

at PowerSder.Pal.ReadOp(Opcode, , UInt32 data1, UInt32 data2, UInt32&  rtn)

atPowerSDR.Console.LoadFWCFirmware(string version)

.

at PowerSDR.Console.Main(String[] args)



Now looking at the stack trace I think the firmware installed correctly but
when it tried to start the process for PowerSDR the call failed. In this
case everything is ok and MS just had a problem trying to start PowerSDR.
Or, did the firmware not get updated correctly.



The radio seems to work fine, imported my database and on the Setup/Hardware
tab the firmware is listed as 2.0.7.2.



Pete W6OP





___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/