Re: panic: vm_fault: fault on nofault entry
Subject: Re: panic: vm_fault: fault on nofault entry, On Wed, 19 Nov 2003 12:38:14 +0900, Jun Kuriyama wrote: > After CVSup'ing to latest source, it can be reproduced. It happens at > "make release". "/mnt" below may indicates this happened at making > floppies with mfs filesystem. Yaeh, latest kernel also caused the same panic at "make release" :-( -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
RE: xl0 watchdog timeout
Subject: RE: xl0 watchdog timeout, On Tue, 04 Nov 2003 12:23:19 -0500 (EST), John Baldwin wrote: > Try disabling ACPI. ACPI is unable to route any of your PCI interrupts, I tried disabling ACPI. It works fine. Thanks John. > so all your PCI interrupts are hosed. You can try to talk with the folks > on acpi-jp@ to figure out if your AML can be patched. OK. I will try to talk with the folks on acpi-jp. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
RE: xl0 watchdog timeout
Subject: RE: xl0 watchdog timeout, On Tue, 04 Nov 2003 10:39:44 -0500 (EST), John Baldwin wrote: > Can you please provide a full dmesg? yes. Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.1-CURRENT #7: Tue Nov 4 19:11:26 JST 2003 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/DAEMON Preloaded elf kernel "/boot/kernel/kernel" at 0xc0793000. Preloaded elf module "/boot/kernel/linux.ko" at 0xc07931f4. Preloaded elf module "/boot/kernel/ipfw.ko" at 0xc07932a0. Preloaded elf module "/boot/kernel/mga.ko" at 0xc079334c. ACPI APIC Table: Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) III CPU family 1266MHz (1267.16-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1 Features=0x383fbff real memory = 1073676288 (1023 MB) avail memory = 1037688832 (989 MB) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0 irqs 0-23 on motherboard Pentium Pro MTRR support enabled npx0: [FAST] npx0: on motherboard npx0: INT 16 interface acpi0: on motherboard pcibios: BIOS version 2.10 Using $PIR table, 7 entries at 0xc00fdc80 acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 acpi_cpu0: on acpi0 acpi_cpu1: on acpi0 acpi_tz0: on acpi0 acpi_button0: on acpi0 pcib0: port 0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0 pcib0: could not get PCI interrupt routing table for \\_SB_.PCI0 - AE_BAD_DATA pci0: on pcib0 agp0: mem 0xe000-0xe3ff at device 0.0 on pci0 pcib1: at device 1.0 on pci0 pci1: on pcib1 drm0: mem 0xe700-0xe77f,0xe600-0xe6003fff,0xe400-0xe5ff irq 10 at device 0.0 on pci1 info: [drm] AGP at 0xe000 64MB info: [drm] Initialized mga 3.1.0 20021029 on minor 0 atapci0: port 0xd000-0xd03f,0xcc00-0xcc03,0x1800-0x1807,0xc400-0xc403,0x1000-0x1007 mem 0xea00-0xea01 irq 19 at device 8.0 on pci0 atapci0: [MPSAFE] ata2: at 0x1000 on atapci0 ata2: [MPSAFE] ata3: at 0x1800 on atapci0 ata3: [MPSAFE] isab0: at device 17.0 on pci0 isa0: on isab0 atapci1: port 0xd400-0xd40f at device 17.1 on pci0 ata0: at 0x1f0 irq 14 on atapci1 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci1 ata1: [MPSAFE] uhci0: port 0xd800-0xd81f irq 11 at device 17.2 on pci0 usb0: on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: port 0xdc00-0xdc1f irq 11 at device 17.3 on pci0 usb1: on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: port 0xe000-0xe01f irq 11 at device 17.4 on pci0 usb2: on uhci2 usb2: USB revision 1.0 uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered xl0: <3Com 3c920B-EMB Integrated Fast Etherlink XL> port 0xe400-0xe47f mem 0xea02-0xea02007f irq 10 at device 18.0 on pci0 xl0: Ethernet address: 00:04:75:3c:6b:ad miibus0: on xl0 ukphy0: on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0 port 0x778-0x77b,0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: on ppc0 lpt0: on ppbus0 lpt0: Interrupt-driven port ppi0: on ppbus0 atkbdc0: port 0x64,0x60 irq 1 on acpi0 atkbd0: flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 orm0: at iomem 0xd4000-0xdc7ff,0xcc000-0xd3fff,0xc-0xc8fff on isa0 pmtimer0 on isa0 sc0: at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: at port 0x3c0-0x3df iomem 0xa-0xb on isa0 Timecounters tick every 10.000 msec ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to accept, logging limited to 5000 packets/entry by default acpi_cpu: throttling enabled, 2 steps (100% to 50.0%), currently 100.0% acd0: DVDROM at ata1-master UDMA66 GEOM: create disk ad4 dp=0xc66ceb70 ad4: 117246MB [238216/16/63] at ata2-master UDMA100 GEOM: create disk ad6 dp=0xc66ce770 ad6: 117246MB [238216/16/63] at ata3-master UDMA100 GEOM: create disk ar0 dp=0xc66c61e0 ar0: 117246MB [14946/255/63] status: READY subdisks: disk0 READY on ad4 at ata2-master disk1 READY on ad6 at ata3-master SMP: AP CPU #1 Launched! Mounting root from ufs:/dev/ar0s1a Accounting enabled xl0: watchdog timeout -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
xl0 watchdog timeout
After cvsup and make world, I could't use xl0 and kernel said "kernel: xl0: watchdog timeout". # dmesg [snip] xl0: <3Com 3c920B-EMB Integrated Fast Etherlink XL> port 0xe400-0xe47f mem 0xea 02-0xea02007f irq 10 at device 18.0 on pci0 xl0: Ethernet address: 00:04:75:3c:6b:ad miibus0: on xl0 ukphy0: on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
DRM related error
Subject: Re: fresh -current trap, On Sat, 25 Oct 2003 04:50:30 +0900, Shin-ichi Yoshimoto wrote: > I'm using a radeon DRM module. Now DRM work fine. But some kernel messages found my log like this. kernel: error: [drm:pid38523:radeon_ioctl] *ERROR* can't find authenticator Is this OK ? -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: fresh -current trap
I also trapped same problem. Subject: Re: fresh -current trap, On Fri, 24 Oct 2003 10:00:57 -0700, Kris Kennaway wrote: > Looks like it might be related to the DRM import from yesterday. > You're not using any modules, are you? I'm using a radeon DRM module. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
cannot boot -s
Hi, After new kernel installing, I cannot boot -s. This kernel always runs multiuser mode. What's happen ?? -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
usr.sbin/ipftest build error
After cvsup, buildworld error in usr.sbin/ipftest [snip] ===> usr.sbin/ipftest cc -O -pipe -march=pentium3 -DUSE_INET6 -DIPL_NAME=\"/dev/ipl\" -DIPFILTER_LOG -I/usr/src/usr.sbin/ipftes t/../../sys/contrib/ipfilter/netinet -I/usr/src/usr.sbin/ipftest/../../sys/contrib/ipfilter -I/usr/src/us r.sbin/ipftest/../../contrib/ipfilter -c /usr/src/contrib/ipfilter/ipt.c [snip] cc -O -pipe -march=pentium3 -DUSE_INET6 -DIPL_NAME=\"/dev/ipl\" -DIPFILTER_LOG -I/usr/src/usr.sbin/ipftest/../../sys/contrib/ipfilter/netinet -I/usr/src/usr.sbin/ipftest/../../sys/contrib/ipfilter -I/usr/src/usr.sbin/ipftest/../../contrib/ipfilter -c /usr/src/sys/contrib/ipfilter/netinet/ip_fil.c In file included from /usr/obj/usr/src/i386/usr/include/net/pfil.h:35, from /usr/src/sys/contrib/ipfilter/netinet/ip_fil.c:314: /usr/obj/usr/src/i386/usr/include/sys/systm.h:154: warning: conflicting types for built-in function `log' /usr/obj/usr/src/i386/usr/include/sys/systm.h:224: error: conflicting types for `setenv' /usr/obj/usr/src/i386/usr/include/stdlib.h:165: error: previous declaration of `setenv' /usr/obj/usr/src/i386/usr/include/sys/systm.h:225: error: conflicting types for `unsetenv' /usr/obj/usr/src/i386/usr/include/stdlib.h:166: error: previous declaration of `unsetenv' In file included from /usr/obj/usr/src/i386/usr/include/sys/systm.h:233, from /usr/obj/usr/src/i386/usr/include/net/pfil.h:35, from /usr/src/sys/contrib/ipfilter/netinet/ip_fil.c:314: /usr/obj/usr/src/i386/usr/include/sys/libkern.h:87: error: conflicting types for `random' /usr/obj/usr/src/i386/usr/include/stdlib.h:206: error: previous declaration of `random' /usr/obj/usr/src/i386/usr/include/sys/libkern.h:96: error: conflicting types for `strdup' /usr/obj/usr/src/i386/usr/include/string.h:80: error: previous declaration of `strdup' In file included from /usr/obj/usr/src/i386/usr/include/net/pfil.h:35, from /usr/src/sys/contrib/ipfilter/netinet/ip_fil.c:314: /usr/obj/usr/src/i386/usr/include/sys/systm.h:263: error: syntax error before "splbio" /usr/obj/usr/src/i386/usr/include/sys/systm.h:264: error: syntax error before "splcam" /usr/obj/usr/src/i386/usr/include/sys/systm.h:265: error: syntax error before "splclock" /usr/obj/usr/src/i386/usr/include/sys/systm.h:266: error: syntax error before "splhigh" /usr/obj/usr/src/i386/usr/include/sys/systm.h:267: error: syntax error before "splimp" /usr/obj/usr/src/i386/usr/include/sys/systm.h:268: error: syntax error before "splnet" /usr/obj/usr/src/i386/usr/include/sys/systm.h:269: error: syntax error before "splsoftcam" /usr/obj/usr/src/i386/usr/include/sys/systm.h:270: error: syntax error before "splsoftclock" /usr/obj/usr/src/i386/usr/include/sys/systm.h:271: error: syntax error before "splsofttty" /usr/obj/usr/src/i386/usr/include/sys/systm.h:272: error: syntax error before "splsoftvm" /usr/obj/usr/src/i386/usr/include/sys/systm.h:273: error: syntax error before "splsofttq" /usr/obj/usr/src/i386/usr/include/sys/systm.h:274: error: syntax error before "splstatclock" /usr/obj/usr/src/i386/usr/include/sys/systm.h:275: error: syntax error before "spltty" /usr/obj/usr/src/i386/usr/include/sys/systm.h:276: error: syntax error before "splvm" /usr/obj/usr/src/i386/usr/include/sys/systm.h:277: error: syntax error before "ipl" In file included from /usr/obj/usr/src/i386/usr/include/net/pfil.h:35, from /usr/src/sys/contrib/ipfilter/netinet/ip_fil.c:314: /usr/obj/usr/src/i386/usr/include/sys/systm.h:42:1: unterminated #ifndef In file included from /usr/src/sys/contrib/ipfilter/netinet/ip_fil.c:314: /usr/obj/usr/src/i386/usr/include/net/pfil.h:32:1: unterminated #ifndef /usr/src/sys/contrib/ipfilter/netinet/ip_fil.c:313:1: unterminated #if *** Error code 1 Stop in /usr/src/usr.sbin/ipftest. *** Error code 1 -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: ATAng no good for me/REQUEST_SENSE recovered from missing interrupt
Subject: Re: ATAng no good for me/REQUEST_SENSE recovered from missing interrupt, On Mon, 22 Sep 2003 03:01:28 +0900, Shin-ichi Yoshimoto wrote: > Ok, I will try it. I tried to cvsup and make build & installkernel. This kernel said: [snip] acpi_cpu: throttling enabled, 2 steps (100% to 50.0%), currently 100.0% GEOM: create disk ad0 dp=0xc63f6570 ad0: 239372MB [486344/16/63] at ata0-master UDMA100 acd0: DVDR at ata1-master UDMA66 (probe2:ata1:0:0:0): Recovered Sense (probe2:ata1:0:0:0): INQUIRY. CDB: 12 1 80 0 ff 0 (probe2:ata1:0:0:0): CAM Status: SCSI Status Error (probe2:ata1:0:0:0): SCSI Status: Check Condition (probe2:ata1:0:0:0): ILLEGAL REQUEST asc:24,0 (probe2:ata1:0:0:0): Invalid field in CDB (probe2:ata1:0:0:0): Recovered Sense (probe2:ata1:0:0:0): INQUIRY. CDB: 12 1 80 0 ff 0 (probe2:ata1:0:0:0): CAM Status: SCSI Status Error (probe2:ata1:0:0:0): SCSI Status: Check Condition (probe2:ata1:0:0:0): ILLEGAL REQUEST asc:24,0 (probe2:ata1:0:0:0): Invalid field in CDB SMP: AP CPU #1 Launched! cd0 at ata1 bus 0 target 0 lun 0 cd0: Removable CD-ROM SCSI-0 device cd0: 66.000MB/s transfers cd0: cd present [2236704 x 2048 byte records] Mounting root from ufs:/dev/ad0s1a [end] Thanks, Thomas !! -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: ATAng no good for me/REQUEST_SENSE recovered from missing interrupt
Subject: Re: ATAng no good for me/REQUEST_SENSE recovered from missing interrupt, On Sun, 21 Sep 2003 18:57:43 +0200, Thomas Quinot wrote: > Can't you drop into DDB at that point? Ok, I will try it. > Also, do you have up-to-date sources? Yes, of course. I have recent ones. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: ATAng no good for me/REQUEST_SENSE recovered from missing interrupt
Subject: Re: ATAng no good for me/REQUEST_SENSE recovered from missing interrupt, On Sun, 21 Sep 2003 00:23:36 +0200, Thomas Quinot wrote: > Can you get a backtrace at that point? I could not get a backtrace because infinite loop occured like this: [snip] ata0-master: pio=0x0c wdma=0x22 udma=0x46 cable=80pin ad0: setting UDMA100 on Intel ICH4 chip GEOM: create disk ad0 dp=0xc6202e70 ad0: ATA-7 disk at ata0-master ad0: 239372MB (490234752 sectors), 486344 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad0 ata1-master: pio=0x0c wdma=0x22 udma=0x44 cable=80pin acd0: setting UDMA66 on Intel ICH4 chip acd0: DVDR drive at ata1 as master acd0: read 5512KB/s (5512KB/s) write 2067KB/s (2067KB/s), 2048KB buffer, UDMA66 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc pcm0: measured ac97 link rate at 47995 Hz, will use 48000 Hz bus_explore done sbp_post_explore (sbp_cold=2) [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:490223412 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s1, start 32256 length 250994386944 end 250994419199 GEOM: Configure ad0s1a, start 0 length 1073741824 end 1073741823 GEOM: Configure ad0s1b, start 1073741824 length 2147483648 end 3221225471 GEOM: Configure ad0s1c, start 0 length 250994386944 end 250994386943 GEOM: Configure ad0s1d, start 3221225472 length 107374182400 end 110595407871 GEOM: Configure ad0s1e, start 110595407872 length 107374182400 end 217969590271 GEOM: Configure ad0s1f, start 217969590272 length 33024796672 end 250994386943 (probe0:ata0:0:0:0): error 22 (probe0:ata0:0:0:0): Unretryable Error (probe1:ata0:0:1:0): error 22 (probe1:ata0:0:1:0): Unretryable Error (probe3:ata1:0:1:0): error 22 (probe3:ata1:0:1:0): Unretryable Error (probe4:sbp0:0:0:0): error 22 (probe4:sbp0:0:0:0): Unretryable Error (probe5:sbp0:0:1:0): error 22 (probe5:sbp0:0:1:0): Unretryable Error (probe6:sbp0:0:2:0): error 22 (probe6:sbp0:0:2:0): Unretryable Error (probe7:sbp0:0:3:0): error 22 (probe7:sbp0:0:3:0): Unretryable Error (probe8:sbp0:0:4:0): error 22 (probe8:sbp0:0:4:0): Unretryable Error (probe9:sbp0:0:5:0): error 22 (probe9:sbp0:0:5:0): Unretryable Error (probe10:sbp0:0:6:0): error 22 (probe10:sbp0:0:6:0): Unretryable Error (probe0:ata0:0:0:0): error 22 (probe0:ata0:0:0:0): Unretryable Error (probe1:ata0:0:1:0): error 22 (probe1:ata0:0:1:0): Unretryable Error (probe3:ata1:0:1:0): error 22 (probe3:ata1:0:1:0): Unretryable Error (probe2:ata1:0:0:0): Retrying Command (probe2:ata1:0:0:0): Retrying Command (probe2:ata1:0:0:0): Retrying Command (probe2:ata1:0:0:0): Retrying Command (probe2:ata1:0:0:0): Retrying Command (probe2:ata1:0:0:0): Retrying Command (probe2:ata1:0:0:0): Retrying Command (probe2:ata1:0:0:0): Retrying Command (probe2:ata1:0:0:0): Retrying Command ..repeat.. .. .. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: ATAng no good for me/REQUEST_SENSE recovered from missing interrupt
Subject: Re: ATAng no good for me/REQUEST_SENSE recovered from missing interrupt, On Sat, 20 Sep 2003 21:53:11 +0200, Thomas Quinot wrote: > Please try the patch below, it should at least work around the problem. I tried your patch. > acd0: WARNING - REQUEST_SENSE recovered from missing interrupt This message disappeared, but It still hang -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
atapicam problem in today's kernel
Today's kernel with atapicam said: acd0: WARNING - REQUEST_SENCE record from missing interrupt and can not boot. Without one is OK. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: BOOTMFS requires 'device miibus'
Subject: Re: BOOTMFS requires 'device miibus',
On Wed, 10 Sep 2003 02:43:23 +0300, Ruslan Ermilov wrote:
> Please try the attached patch instead, and let me know if it fixes
> the release build. You can try ``make rerelease'' to speed up the
> things, after applying this patch in ${CHROOTDIR}/usr/src.
This patch is good for me. But another problem ...
[snip]
touch release.9
Making the drivers floppy.
Copying cd9660.ko to /R/stage/driversfd
Copying if_awi.ko to /R/stage/driversfd
Copying if_sk.ko to /R/stage/driversfd
Copying if_fwe.ko to /R/stage/driversfd
Copying if_sl.ko to /R/stage/driversfd
Copying if_sn.ko to /R/stage/driversfd
Copying amr.ko to /R/stage/driversfd
Copying sbp.ko to /R/stage/driversfd
Copying twe.ko to /R/stage/driversfd
Copying if_re.ko to /R/stage/driversfd
Copying mly.ko to /R/stage/driversfd
Copying trm.ko to /R/stage/driversfd
Copying agp.ko to /R/stage/driversfd
Copying rc4.ko to /R/stage/driversfd
Copying if_wi.ko to /R/stage/driversfd
Copying msdosfs.ko to /R/stage/driversfd
Copying if_axe.ko to /R/stage/driversfd
Copying firewire.ko to /R/stage/driversfd
Copying if_ti.ko to /R/stage/driversfd
Copying if_ex.ko to /R/stage/driversfd
Copying if_de.ko to /R/stage/driversfd
Copying if_bfe.ko to /R/stage/driversfd
Copying wlan.ko to /R/stage/driversfd
Copying if_tl.ko to /R/stage/driversfd
Copying if_ie.ko to /R/stage/driversfd
Copying nfsclient.ko to /R/stage/driversfd
Copying ips.ko to /R/stage/driversfd
Copying plip.ko to /R/stage/driversfd
Copying if_tx.ko to /R/stage/driversfd
Copying if_an.ko to /R/stage/driversfd
rmdir: /R/stage/driversfd: Directory not empty
*** Error code 1 (ignored)
if [ -d /R/stage/driversfd ]; then sh -e
/usr/src/release/scripts/doFS.sh bsdlabel ""
/R/stage/floppies/drivers.flp /R/stage /mnt 1440 /R/stage/driversfd
4 fd1440; cd /R/stage/driversfd && awk -f
/usr/src/release/scripts/driver-desc.awk *.dsc >>
/R/stage/floppies/DRIVERS.TXT; fi
+ export BLOCKSIZE=512
+ DISKLABEL=bsdlabel
+ shift
+ MACHINE=
+ shift
+ FSIMG=/R/stage/floppies/drivers.flp
+ shift
+ RD=/R/stage
+ shift
+ MNT=/mnt
+ shift
+ FSSIZE=1440
+ shift
+ FSPROTO=/R/stage/driversfd
+ shift
+ FSINODE=4
+ shift
+ FSLABEL=fd1440
+ shift
+ [ 1440 -eq 0 -a fd1440 = auto ]
+ [ -f /R/stage/trees/base/boot/boot ]
+ BOOT=-B -b /R/stage/trees/base/boot/boot
+ deadlock=20
+ uname -r
+ dofs_md
+ true
+ rm -f /R/stage/floppies/drivers.flp
+ [ x != x ]
+ dd of=/R/stage/floppies/drivers.flp if=/dev/zero count=1440 bs=1k
+ mdconfig -a -t vnode -f /R/stage/floppies/drivers.flp
+ MDDEVICE=md0
+ [ ! -c /dev/md0 ]
+ trap umount /mnt; mdconfig -d -u md0 EXIT
+ bsdlabel -w -B -b /R/stage/trees/base/boot/boot md0 fd1440
+ newfs -O1 -i 4 -o space -m 0 /dev/md0c
fstab: /etc/fstab:0: No such file or directory
/dev/md0c: 1.4MB (2880 sectors) block size 4096, fragment size 512
using 2 cylinder groups of 1.22MB, 312 blks, 32 inodes.
super-block backups (for fsck -b #) at:
32, 2528
+ mount /dev/md0c /mnt
+ [ -d /R/stage/driversfd ]
+ set -e
+ cd /R/stage/driversfd
+ find+ cpio . -dump -print /mnt
cpio: write error: No space left on device
+ umount /mnt
+ mdconfig -d -u md0
*** Error code 1
Stop in /usr/src/release.
+ umount /dev
*** Error code 1
Stop in /usr/src/release.
--
Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]>
http://diary.waishi.jp/~yosimoto/diary/
___
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
BOOTMFS requires 'device miibus'
make release failed because BOOTMFS forgot "device miibus" Please add this option in BOOTMFS. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: My current box still got panic after ATAng
Subject: Re: My current box still got panic after ATAng, On Tue, 9 Sep 2003 09:19:01 +0200 (CEST), Soren Schmidt wrote: > Hmm, have you run fsck on that filesystem lately ? Yes, every panic. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
My current box still got panic after ATAng
0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered ehci0: mem 0xffaffc00-0xffaf irq 18 at device 29.7 on pci0 ehci_pci_attach: companion usb0 ehci_pci_attach: companion usb1 ehci_pci_attach: companion usb2 ehci_pci_attach: companion usb3 usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: on ehci0 usb4: USB revision 2.0 uhub4: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub4: 8 ports with 8 removable, self powered pcib3: at device 30.0 on pci0 pci3: on pcib3 fwohci0: mem 0xff9ff000-0xff9f irq 19 at device 7.0 on pci3 fwohci0: [MPSAFE] fwohci0: OHCI version 1.0 (ROM=0) fwohci0: No. of Isochronous channel is 8. fwohci0: EUI64 00:07:e9:00:00:70:f9:c4 fwohci0: Phy 1394a available S400, 3 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: on fwohci0 sbp0: on firewire0 if_fwe0: on firewire0 if_fwe0: Fake Ethernet address: 02:07:e9:70:f9:c4 fwohci0: Initiate bus reset fwohci0: BUS reset fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) isab0: at device 31.0 on pci0 isa0: on isab0 atapci0: port 0xffa0-0xffaf,0-0x3,0-0x7,0-0x3,0-0x7 irq 17 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] atapci1: port 0xdc00-0xdc0f,0xe000-0xe003,0xe400-0xe407,0xe800-0xe803,0xec00-0xec07 irq 17 at device 31.2 on pci0 atapci1: [MPSAFE] ata2: at 0xec00 on atapci1 ata2: [MPSAFE] ata3: at 0xe400 on atapci1 ata3: [MPSAFE] ichsmb0: port 0xc800-0xc81f irq 19 at device 31.3 on pci0 smbus0: on ichsmb0 smb0: on smbus0 pcm0: mem 0xffaff400-0xffaff4ff,0xffaff800-0xffaff9ff irq 19 at device 31.5 on pci0 pcm0: acpi_button0: on acpi0 atkbdc0: port 0x64,0x60 irq 1 on acpi0 atkbd0: flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 fdc0: port 0x3f7,0x3f4-0x3f5,0x3f2-0x3f3,0x3f0-0x3f1 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A, console ppc0 port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode ppbus0: on ppc0 lpt0: on ppbus0 lpt0: Interrupt-driven port ppi0: on ppbus0 orm0: at iomem 0xc-0xcafff on isa0 pmtimer0 on isa0 sc0: at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: at port 0x3c0-0x3df iomem 0xa-0xb on isa0 APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 Timecounters tick every 10.000 msec ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to deny, logging limited to 5000 packets/entry by default acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% acd0: DVDR at ata1-master UDMA66 em0: Link is up 100 Mbps Full Duplex GEOM: create disk ad4 dp=0xc62faa70 ad4: 239372MB [486344/16/63] at ata2-master UDMA133 SMP: AP CPU #1 Launched! Mounting root from ufs:/dev/ad4s1a em0: Link is up 100 Mbps Full Duplex Accounting enabled -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: installworld broken
Subject: installworld broken, On Mon, 8 Sep 2003 23:42:43 +0900, Shin-ichi Yoshimoto wrote: > Hi, make installworld is broken like this. Sorry. After buildworld, buildkernl, and installkernel, everything is OK. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
installworld broken
Hi, make installworld is broken like this. -- >>> Installing everything.. -- cd /usr/src; make -f Makefile.inc1 install ===> share/info ===> include creating osreldate.h from newvers.sh touch: not found *** Error code 127 Stop in /usr/src/include. *** Error code 1 any idea ? -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: make buildworld broken in telnetd
Subject: make buildworld broken in telnetd, On Wed, 3 Sep 2003 19:14:10 +0900, Shin-ichi Yoshimoto wrote: > make buildworld broken in libexec/telnetd. I tried to backout share/bsd.lib.mk from rev.1.152 to rev 1.151, buildworld is ok. Is the rev.1.152 anything wrong ? -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
make buildworld broken in telnetd
make buildworld broken in libexec/telnetd. [snip] ===> libexec/telnetd cc -O -pipe -march=pentium4 -DLINEMODE -DUSE_TERMIO -DDIAGNOSTICS -DOLD_ENVIRON -DENV_HACK -I/usr/src/l ibexec/telnetd/../../contrib/telnet -DINET6 -DAUTHENTICATION -DENCRYPTION -DKRB5 -DFORWARD -Dnet_write=te lnet_net_write -Wsystem-headers -Werror -Wall -Wno-format-y2k -Wno-uninitialized -c /usr/src/contrib/tel net/telnetd/global.c [snip] cc -O -pipe -march=pentium4 -DLINEMODE -DUSE_TERMIO -DDIAGNOSTICS -DOLD_ENVIRON -DENV_HACK -I/usr/src/l ibexec/telnetd/../../contrib/telnet -DINET6 -DAUTHENTICATION -DENCRYPTION -DKRB5 -DFORWARD -Dnet_write=te lnet_net_write -Wsystem-headers -Werror -Wall -Wno-format-y2k -Wno-uninitialized -o telnetd global.o sl c.o state.o sys_term.o telnetd.o termstat.o utility.o authenc.o -lutil -ltermcap /usr/obj/usr/src/libexec /telnetd/../../lib/libtelnet/libtelnet.a -lmp -lcrypto -lcrypt -lpam -lkrb5 -lasn1 -lroken -lcom_err /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `_ossl_old_des_set_key' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `RAND_write_file' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `_ossl_old_des_set_odd_parity' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `RC4_set_key' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `MD4_Update' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `RC4' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `_ossl_old_des_cbc_cksum' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `RAND_file_name' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `MD4_Final' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `MD5_Init' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `_ossl_old_des_cbc_encrypt' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `crypt' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `MD5_Final' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `_ossl_old_des_read_pw_string' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `MD4_Init' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `_ossl_old_des_is_weak_key' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `_ossl_old_des_ede3_cbc_encrypt' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `MD5_Update' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `_ossl_old_des_pcbc_encrypt' /usr/obj/usr/src/i386/usr/lib/libkrb5.so: undefined reference to `_ossl_old_des_cfb64_encrypt' *** Error code 1 Stop in /usr/src/libexec/telnetd. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: ATAng related panic
Subject: Re: ATAng related panic, On Mon, 25 Aug 2003 01:45:05 -0600, David R. Colyer wrote: > I noticed in your dmesg that you have hyperthreading support on a 3 ghz p4 > like mine. Could you email me and/or post your kernel config file and/or > whatever else you did to get this to compile and work. Please OK. Please check this URL. <http://diary.waishi.jp/%7Eyosimoto/myconfig.txt> -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: ATAng related panic
tapci1 ichsmb0: port 0xc800-0xc81f irq 19 at device 31.3 on pci0 pcm0: mem 0xffaff400-0xffaff4ff,0xffaff800-0xffaff9ff irq 19 at device 31.5 on pci0 pcm0: acpi_button0: on acpi0 atkbdc0: port 0x64,0x60 irq 1 on acpi0 atkbd0: flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 fdc0: port 0x3f7,0x3f4-0x3f5,0x3f2-0x3f3,0x3f0-0x3f1 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A, console ppc0 port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode ppbus0: on ppc0 lpt0: on ppbus0 lpt0: Interrupt-driven port ppi0: on ppbus0 orm0: at iomem 0xc-0xcafff on isa0 pmtimer0 on isa0 sc0: at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: at port 0x3c0-0x3df iomem 0xa-0xb on isa0 APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 Timecounters tick every 10.000 msec ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to deny, logging limited to 5000 packets/entry by default acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% acd0: DVDR at ata1-master UDMA66 em0: Link is up 100 Mbps Full Duplex ad4: 239372MB [486344/16/63] at ata2-master UDMA133 SMP: AP CPU #1 Launched! Mounting root from ufs:/dev/ad4s1a -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: ATAng related panic
Subject: Re: ATAng related panic, On Mon, 25 Aug 2003 08:32:02 +0200 (CEST), Soren Schmidt wrote: > Is this with the ATAng from my ftp server or the one now in current ? in current. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
ATAng related panic
I have been using the ATAng kernel. This kernel got the panic
when I tried to do CVSup like this.
panic: ata_dmasetup: transfer active on this device!
cpuid = 0; lapic.id =
Debugger("panic")
Stopped at Debugger+0x4f: xchgl %ebx,in_Debugger.0
db> t
Debugger(c03648b2,0,c0356485,dfb36b70,100) at Debugger+0x4f
panic(c0356485,dfb36b90,c014581f,c6212880,c02ee508) at panic+0x153
ata_dmastart(c6187c00,d3787000,800,4,101) at ata_dmastart+0x27
ata_pci_dmastart(c6187c00,d3787000,800,4,4) at ata_pci_dmastart+0x29
ata_transaction(c7b41a80,c7b41a80,1f4,c62fa100,c62fa100) at ata_transaction+0x973
ata_start(c6187c00,c6445c60,0,10,10) at ata_start+0x220
adstrategy(c6445c60,10,200,0,0) at adstrategy+0xd3
g_disk_start(c6832c60,0,24c,c0360e4d,a) at g_disk_start+0x1b1
g_io_schedule_down(c21b9d10,c60823c8,dfb36d34,c01e5ccc,0) at g_io_schedule_down+0x1b7
g_down_procbody(0,dfb36d48,800,1000,0) at g_down_procbody+0x1e
fork_exit(c01c45b0,0,dfb36d48) at fork_exit+0xb2
fork_trampoline() at fork_trampoline+0x8
--- trap 0x1, eip = 0, esp = 0xdfb36d7c, ebp = 0 ---
db>
--
Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]>
http://diary.waishi.jp/~yosimoto/diary/
___
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: Release seems to be broken or maybe I missed a change.
Subject: Release seems to be broken or maybe I missed a change., On Wed, 20 Aug 2003 10:34:43 -0700, [EMAIL PROTECTED] wrote: > With cvsup early this morning. Make release generated Which version of src/libexec/rtld-elf/Makefile are you using ? This problem was fixed a few days ago. > install -o root -g wheel -m 444 rtld.1.gz /usr/share/man/man1 > /usr/share/man/man1/ld-elf.so.1.1.gz -> /usr/share/man/man1/rtld.1.gz > /usr/share/man/man1/ld.so.1.gz -> /usr/share/man/man1/rtld.1.gz > /usr/libexec/ld-elf.so.1 -> /libexec/ld-elf.so.1 > ln: /usr/libexec/ld-elf.so.1: Operation not permitted > *** Error code 1 -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: HEADS UP: dynamic root support now in the tree
Subject: Re: HEADS UP: dynamic root support now in the tree,
On Mon, 18 Aug 2003 04:28:53 +0900, Shin-ichi Yoshimoto wrote:
> Thanks Gordon. I can save a space :-)
I found another problem in src/Makefile.inc
[snip]
.if ${TARGET_ARCH} == ${MACHINE_ARCH} && !defined(DISTDIR) && \
(!defined(DESTDIR) || empty(DESTDIR) || ${DESTDIR} == "/")
@echo "Checking to see if your booted kernel is fresh enough.."
${.OBJDIR}/bin/sh/sh -c \
'echo "Testing installed kernel for new sigaction(2)
syscall"'
@echo "Seems ok.."
.endif
[snip]
${.OBJDIR}/bin/sh/sh is dynamically-linked if WITH_DYNAMICROOT is
defined. But sh cannot find /libexec/ld-elf.so.1 before instaling
/libexec/ld-elf.so.1.
Is this right ?
--
Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]>
http://diary.waishi.jp/~yosimoto/diary/
___
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: HEADS UP: dynamic root support now in the tree
Subject: Re: HEADS UP: dynamic root support now in the tree, On Sun, 17 Aug 2003 12:05:34 -0700, Gordon Tetlow wrote: >> Thanks for reporting this. I've fixed it in rev 1.22 of >> src/libexec/rtld-elf/Makefile. > > Silly me forgot to honor DESTDIR. rev 1.23 is much better =) Thanks Gordon. I can save a space :-) -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: HEADS UP: dynamic root support now in the tree
make installworld broken. ==>libexex/rtld-elf [snip] ln: /usr/libexec/ld-elf.so.1: Operation not permitted *** Error code 1 any idea ? -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: buildworld broken after installworld
Subject: Re: buildworld broken after installworld, On Mon, 4 Aug 2003 18:14:04 +0400, Andrey Chernov wrote: > I just commit the fix to makelist, see explanation in the commit message. Just fine for "LANG=en_US.ISO8859-1". Thank you. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: buildworld broken after installworld
Subject: Re: buildworld broken after installworld, On Mon, 4 Aug 2003 17:57:13 +0400, Andrey Chernov wrote: > Well, I found error in the archives, so the question remains, what locale > you use? LANG=en_US.ISO8859-1 -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: buildworld broken after installworld
Subject: Re: buildworld broken after installworld, On Mon, 4 Aug 2003 14:47:23 +0300, Ruslan Ermilov wrote: > Too bad. I think this may be related to a recent work of Andrey > on tr(1), as fcns.h is generated using src/lib/libedit/makelist. > Perhaps, just enforcing the C locale will fix it. Yes. I tried to "setenv LANG C", just fine. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
buildworld broken after installworld
I tried to buildworld and installworld in this morning. After that, buildworld broken like this: [snip] ===> lib/libedit cc -O -pipe -march=pentium4 -I. -I/usr/src/lib/libedit -c editline.c In file included from /usr/src/lib/libedit/chared.h:136, from /usr/src/lib/libedit/el.h:102, from /usr/src/lib/libedit/chared.c:51, from editline.c:4: fcns.h:94:12: warning: ISO C requires whitespace after the macro name In file included from editline.c:9: help.c:51: error: `VI_ZERO' undeclared here (not in a function) [snip] and I checked fcns.h:94. > cat /usr/obj/usr/src/lib/libedit/fcns.h [snip] #define VI_UNDO_LINE 89 #define VI_]ERO 90<--- ??? #define EL_NUM_FCNS 91 typedef el_action_t (*el_func_t)(EditLine *, int); protected const el_func_t* func__get(void); #endif /* _h_fcns_c */ -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: 5.1 RELEASE bugs?
Subject: 5.1 RELEASE bugs?, On Sun, 13 Jul 2003 12:05:20 +0200 (CEST), Christer Gundersen wrote: > the word 'pentium3' dont exist in make.conf. see /usr/src/share/mk/bsd.cpu.mk -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
mergemaster broken
mergemaster broken in today's current like this: > mergemaster -dv [snip] cd /usr/src/etc/sendmail; make distribution install -o root -g wheel -m 644 /usr/src/etc/sendmail/freebsd.mc freebsd.cf /var/tmp/temproot.0707.11.55/etc/mail install: freebsd.cf: No such file or directory *** Error code 71 Stop in /usr/src/etc/sendmail. *** Error code 1 Stop in /usr/src/etc. *** FATAL ERROR: Cannot 'cd' to /usr/src/etc and install files to the temproot environment -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: [acpi-jp 2269] Re: HEADSUP: acpi patches in the tree
Subject: Re: [acpi-jp 2269] Re: HEADSUP: acpi patches in the tree, On Tue, 27 May 2003 17:56:47 -0700 (PDT), Nate Lawson wrote: > Please respond to my other email as well. Without that patch, do you have > problems or is it just the error message? Oh, sorry. Without that patch, no problems. It's only the error message. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: HEADSUP: acpi patches in the tree
Subject: Re: HEADSUP: acpi patches in the tree, > Please try the attached patch and see if it changes things for you. OK. I tried youre patch. Error messages is gone :-) Thanks ! acpi0: on motherboard pcibios: BIOS version 2.10 Using $PIR table, 7 entries at 0xc00fdee0 acpi0: power button is handled as a fixed feature programming model. -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: HEADSUP: acpi patches in the tree
Subject: HEADSUP: acpi patches in the tree, On Tue, 27 May 2003 14:06:50 -0700 (PDT), Nate Lawson wrote: > I have committed changes to nsalloc.c and dsmethod.c. Please cvsup and > test ACPI, especially if you had problems with it (that were not present > before 0228 was imported). After this update, I found some error messages like this: acpi0: on motherboard ACPI-0438: *** Error: Looking up [\\_OS_] in namespace, AE_NOT_FOUND ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0._INI] (Node 0xc21b73e0), AE_NOT_FOUND -- Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> http://diary.waishi.jp/~yosimoto/diary/ ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: make buildworld broken in usr.bin/systat
At 10:05 +0900 08/25/2000, Jun Kuriyama wrote: > I have same problem with today's -current. This problem was fixed by At 13:22 -0700 08/24/2000, Peter Wemm wrote: > peter 2000/08/24 13:22:44 PDT > > Modified files: > usr.bin/systat swap.c > Log: > Quick Fix: swap.c doesn't appear to actually need , so remove > it to try and get world building again. (sys/conf.h now depends on > sys/types.h) > > Revision ChangesPath > 1.14 +1 -2 src/usr.bin/systat/swap.c Thanks peter. ------ Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> KEK, High Energy Accelerator Research Organization Accelerator Laboratory To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
make buildworld broken in usr.bin/systat
make buildworld failed this morning. Error messages are as follows: ===> usr.bin/systat [snip] cc -O -pipe -I/usr/src/usr.bin/systat/../../sys -I/usr/obj/usr/src/i386/usr/include -c /usr/src/usr.bin/systat/swap.c In file included from /usr/src/usr.bin/systat/swap.c:47: /usr/src/usr.bin/systat/../../sys/sys/conf.h:59: field `si_atime' has incomplete type /usr/src/usr.bin/systat/../../sys/sys/conf.h:60: field `si_ctime' has incomplete type /usr/src/usr.bin/systat/../../sys/sys/conf.h:61: field `si_mtime' has incomplete type *** Error code 1 Stop in /usr/src/usr.bin/systat. -- KEK, High Energy Accelerator Research Organization Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
make buildworld broken in libcrypto.
I got the following error while trying to make builworld with WITH_IDEA=YES and USA_RESIDENT=NO. ===> libcrypto [snip] cc -O -pipe -DTERMIOS -DANSI_SOURCE -I/usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto -I/usr/obj/usr/src/secure/lib/libcrypto -DL_ENDIAN -I/usr/obj/usr/src/i386/usr/include -c /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c -o e_cbc_i.o /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c:7 8: union has no member named `idea_ks' /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c: In function `idea_cbc_init_key': /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c:9 7: union has no member named `idea_ks' /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c:1 00: syntax error before `tmp' /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c:1 02: `tmp' undeclared (first use in this function) /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c:1 02: (Each undeclared identifier is reported only once /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c:1 02: for each function it appears in.) /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c:1 03: union has no member named `idea_ks' /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c:1 05: `IDEA_KEY_SCHEDULE' undeclared (first use in this function) /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c: In function `idea_cbc_cipher': /usr/src/secure/lib/libcrypto/../../../crypto/openssl/crypto/evp/e_cbc_i.c:1 15: union has no member named `idea_ks' *** Error code 1 Stop in /usr/src/secure/lib/libcrypto. ------ Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> KEK, High Energy Accelerator Research Organization Accelerator Laboratory To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
make release still broken
bsd.ports.mk don't have the version of new perl (5.006). So, make release still broken. chflags -R noschg /R/stage/trees touch release.2 Making docs... ===> Extracting for docproj-1.1 >> No MD5 checksum file. ===> Patching for docproj-1.1 ===> Configuring for docproj-1.1 ===> Installing for docproj-1.1 ===> docproj-1.1 depends on executable: instant - not found ===>Verifying install for instant in /usr/ports/textproc/sgmlformat Error: you don't have the right version of perl in /usr/bin. *** Error code 1 Stop. *** Error code 1 Stop in /usr/ports/textproc/docproj. *** Error code 1 Stop in /usr/ports/textproc/docproj. *** Error code 1 Stop in /usr/ports/textproc/docproj. *** Error code 1 Stop in /usr/src/release. *** Error code 1 Stop in /usr/src/release. ------ Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> KEK, High Energy Accelerator Research Organization Accelerator Laboratory To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
Re: Anyone have OpenSSH + X11-fwd working?
At 10:01 -0400 04/17/2000, Brian Fundakowski Feldman wrote: > Has anyone tried it recently and gotten it to work? Yes, sure. Check your config file. $ cat ~/.ssh/config | grep ^ForwardX11 ForwardX11 yes -- KEK, High Energy Accelerator Research Organization Accelerator Laboratory Shin-ichi YOSHIMOTO <[EMAIL PROTECTED]> To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
