Hifn Panic on Soekris net4501

[Stephan Holtwisch]

Hi,

attached the kernel panic, without the hifn driver the kernel
boots without problems. Its somewhat difficult to debug though,
since this system resides on Sandisk without anything
than a kernel yet.

Stephan

FreeBSD 5.0-CURRENT #1: Sat Nov 9 20:47:41 CET 20021 A0004000 09
root@darkstar:/usr/src/sys/i386/compile/SOEKRIS2
Preloaded elf kernel /kernel at 0xc03b3000.for entering Monitor.
Timecounter i8254 frequency 1189163 Hz
CPU: AMD Am5x86 Write-Back (486-class CPU)
Origin = AuthenticAMD Id = 0x4f4 Stepping = 4
Features=0x1FPU
real memory = 67108864 (65536K bytes)
avail memory = 61280256 (59844K bytes)
Initializing GEOMetry subsystem
npx0: math processor on motherboard
npx0: INT 16 interface
Timecounter ELAN frequency 833 Hz
pcib0: AMD Elan SC520 host to PCI bridge at pcibus 0 on motherboard
pci0: PCI bus on pcib0
hifn0 mem 0xa0001000-0xa0001fff,0xa000-0xafff irq 10 at device 16.0 
on p
ci0
hifn0: Hifn 7951, rev 0, 128KB sram, 193 sessions

Fatal trap 12: page fault while in kernel mode
fault virtual address = 0x68
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc01af9cd
stack pointer = 0x10:0xc03d5b88
frame pointer = 0x10:0xc03d5b9c
code segment = base 0x0, limit 0xf, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 0 (swapper)
trap number = 12
panic: page fault
Uptime: 1s
Automatic reboot in 15 seconds - press a key on the console to abort
-- Press a key on the console to reboot,
-- or switch off the system now.
-
Stephan Holtwisch - [EMAIL PROTECTED]
immutec GmbH - Mendelstraße 11 - 48149 Münster
Tel: +49(0)251/980-1230 - Fax: +49(0)251/980-1231
www.immutec.com - [EMAIL PROTECTED]


To Unsubscribe: send mail to [EMAIL PROTECTED]
with unsubscribe freebsd-current in the body of the message

CF-PCMCIA Adapter + CF-Card

[Stephan Holtwisch]

Hi,

i had a similar problem as reported by Tomi Vainio on 27.09.2002
with a CF-PCMCIA Adapter and a Sandisk 64MB CF Card with NEWCARD on a
- -current of  ~ 20.09.2002:

(This is a Thinkpad X20)

pccard0: Allocation failed for cfe 0
ata2 at port 0x100-0x10f irq 11 function 0 config 1 on pccard0
pccard0: WARNING: Resource not reserved by pccard bus
device_probe_and_attach: ata2 attach returned 6

On todays Current i get on Insertion:

pccard0: Allocation failed for cfe 0
ata2 at port 0x100-0x10f irq 11 function 0 config 1 on pccard0
ad4: 61MB SanDisk SDCFB-64 [490/8/32] at ata2-master BIOSPIO

On todays Current i get on Boot:

pccard0: Allocation failed for cfe 0
ata2 at port 0x100-0x10f irq 11 function 0 config 1 on pccard0
ad0: 19077MB HITACHI_DK23BA-20B [41344/15/63] at ata0-master UDMA33
ad4: READ command timeout tag=0 serv=0 - resetting
ata2: resetting devices ..
done
ad4: read interrupt arrived early
ad4: read error detected (too) late
ad4: SanDisk SDCFB-64 [490/8/32] at ata2-master BIOSPIO
ad4: hard error cmd=read fsbn 104458130 of 0-3
  status=51 error=10
ad4: 51004MB SanDisk SDCFB-64 [21318/70/70] at ata2-master BIOSPIO

at that point the kernel hangs :-)

If i insert the card after the boot Process i can work on it without
any Problems...

Stephan
-
Stephan Holtwisch - [EMAIL PROTECTED]
immutec GmbH - Mendelstraße 11 - 48149 Münster
Tel: +49(0)251/980-1230 - Fax: +49(0)251/980-1231
www.immutec.com - [EMAIL PROTECTED]


To Unsubscribe: send mail to [EMAIL PROTECTED]
with unsubscribe freebsd-current in the body of the message