Re: Huawei 3g Modem
Quoting David Schulz <[EMAIL PROTECTED]>: i have a Huawei EC-325 Modem which is connected to my Computer running FreeBSD 6.3 with a mini-USB Cable, and supposedly is supported by the ubsa driver, as described here "http://www.freebsd.org/cgi/man.cgi?query=ubsa&sektion=4&manpath=FreeBSD+6.3-RELEASE ". I modified my /boot/loader.conf to yield the following: ubsa_load="YES" ucom_load="YES" After rebooting, kldstat shows the above modules loaded. When i re-insert my Huawei Modem, dmesg displays: ucom0: Huawei Technologies Huawei Mobile, rev 1.01/0.00, addr 2 So the driver is attaching. That's good. My ppp.conf looks like this: default: set log Phase Chat LCP IPCP CCP tun command ident user-ppp VERSION (built COMPILATIONDATE) set device /dev/cuaU0 set speed 230400 set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \ \"\" AT OK-AT-OK AT&FE0V1X1&D2&C1S0=0 OK \\dATDT\\T TIMEOUT 40 CONNECT" set timeout 180# 3 minute idle timer (the default) enable dns # request DNS info (for resolv.conf) three: set phone \#77 Are you sure it's not #777? set authname card set authkey card disable ipv6cp set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0 add default HISADDR But when i run ppp -ddial three , ppp.log reports this output: Jan 28 15:32:57 testbed ppp[824]: Phase: Using interface: tun0 Jan 28 15:32:57 testbed ppp[824]: Phase: deflink: Created in closed state Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: ident user- ppp VERSION (built COMPILATIONDATE) Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: set device / dev/cuaU0 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: set speed 230400 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: set dial ABORT BUSY ABORT NO\sCARRIER TIMEOUT 5 "" AT OK-AT-OK AT&FE0V1X1&D2&C1S0=0 OK \dATDT\T TIMEOUT 40 CONNECT Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: set timeout 180 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: enable dns Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: set phone #77 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: set authname card Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: set authkey Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: disable ipv6cp Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: add default HISADDR Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: PPP Started (ddial mode). Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: bundle: Establish Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: deflink: closed -> opening Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: deflink: Connected! Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: deflink: opening -> dial Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Phone: #77 Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Send: AT^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Expect(5): OK Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Received: ^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Received: OK^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Send: AT&FE0V1X1&D2&C1S0=0^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Expect(5): OK Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Received: AT&FE0V1X1&D2&C1S0=0^M^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Received: OK^M This all looks great and indicates that communication with the modem is indeed happening. Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Send: ATDT#77^M Jan 28 15:32:59 testbed ppp[825]: tun0: Chat: Expect(40): CONNECT Jan 28 15:33:12 testbed ppp[825]: tun0: Chat: Received: ^M Jan 28 15:33:12 testbed ppp[825]: tun0: Chat: Received: NO CARRIER^M Jan 28 15:33:12 testbed ppp[825]: tun0: Warning: Chat script failed Jan 28 15:33:12 testbed ppp[825]: tun0: Phase: deflink: dial -> hangup Jan 28 15:33:12 testbed ppp[825]: tun0: Warning: deflink: Unable to set physical to speed 0 Jan 28 15:33:12 testbed ppp[825]: tun0: Phase: deflink: Disconnected! Jan 28 15:33:12 testbed ppp[825]: tun0: Warning: deflink: Unable to set physical to speed 0 Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: deflink: Connect time: 17 secs: 0 octets in, 0 octets out Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: deflink: 0 packets in, 0 packets out Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Mon Jan 28 15:32:57 2008 Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: deflink: hangup -> opening Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: deflink: Enter pause (30) for redialing. Obviously things start to go south here, but it could just be a matter of tuning your ppp setup and verifying all your information. Running ppp in the foreground with a manual terminal session is a good place to start troubleshooting. Additionally, after
Huawei 3g Modem
Hello, i have a Huawei EC-325 Modem which is connected to my Computer running FreeBSD 6.3 with a mini-USB Cable, and supposedly is supported by the ubsa driver, as described here "http://www.freebsd.org/cgi/man.cgi?query=ubsa&sektion=4&manpath=FreeBSD+6.3-RELEASE ". I modified my /boot/loader.conf to yield the following: ubsa_load="YES" ucom_load="YES" After rebooting, kldstat shows the above modules loaded. When i re-insert my Huawei Modem, dmesg displays: ucom0: Huawei Technologies Huawei Mobile, rev 1.01/0.00, addr 2 My ppp.conf looks like this: default: set log Phase Chat LCP IPCP CCP tun command ident user-ppp VERSION (built COMPILATIONDATE) set device /dev/cuaU0 set speed 230400 set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \ \"\" AT OK-AT-OK AT&FE0V1X1&D2&C1S0=0 OK \\dATDT\\T TIMEOUT 40 CONNECT" set timeout 180# 3 minute idle timer (the default) enable dns # request DNS info (for resolv.conf) three: set phone \#77 set authname card set authkey card disable ipv6cp set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0 add default HISADDR But when i run ppp -ddial three , ppp.log reports this output: Jan 28 15:32:57 testbed ppp[824]: Phase: Using interface: tun0 Jan 28 15:32:57 testbed ppp[824]: Phase: deflink: Created in closed state Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: ident user- ppp VERSION (built COMPILATIONDATE) Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: set device / dev/cuaU0 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: set speed 230400 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: set dial ABORT BUSY ABORT NO\sCARRIER TIMEOUT 5 "" AT OK-AT-OK AT&FE0V1X1&D2&C1S0=0 OK \dATDT\T TIMEOUT 40 CONNECT Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: set timeout 180 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: default: enable dns Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: set phone #77 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: set authname card Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: set authkey Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: disable ipv6cp Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0 Jan 28 15:32:57 testbed ppp[824]: tun0: Command: three: add default HISADDR Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: PPP Started (ddial mode). Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: bundle: Establish Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: deflink: closed -> opening Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: deflink: Connected! Jan 28 15:32:57 testbed ppp[825]: tun0: Phase: deflink: opening -> dial Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Phone: #77 Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Send: AT^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Expect(5): OK Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Received: ^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Received: OK^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Send: AT&FE0V1X1&D2&C1S0=0^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Expect(5): OK Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Received: AT&FE0V1X1&D2&C1S0=0^M^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Received: OK^M Jan 28 15:32:57 testbed ppp[825]: tun0: Chat: Send: ATDT#77^M Jan 28 15:32:59 testbed ppp[825]: tun0: Chat: Expect(40): CONNECT Jan 28 15:33:12 testbed ppp[825]: tun0: Chat: Received: ^M Jan 28 15:33:12 testbed ppp[825]: tun0: Chat: Received: NO CARRIER^M Jan 28 15:33:12 testbed ppp[825]: tun0: Warning: Chat script failed Jan 28 15:33:12 testbed ppp[825]: tun0: Phase: deflink: dial -> hangup Jan 28 15:33:12 testbed ppp[825]: tun0: Warning: deflink: Unable to set physical to speed 0 Jan 28 15:33:12 testbed ppp[825]: tun0: Phase: deflink: Disconnected! Jan 28 15:33:12 testbed ppp[825]: tun0: Warning: deflink: Unable to set physical to speed 0 Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: deflink: Connect time: 17 secs: 0 octets in, 0 octets out Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: deflink: 0 packets in, 0 packets out Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Mon Jan 28 15:32:57 2008 Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: deflink: hangup -> opening Jan 28 15:33:14 testbed ppp[825]: tun0: Phase: deflink: Enter pause (30) for redialing. Additionally, after running ppp -ddial three, dmesg shows a lot of lines like these: ucom0: ubsa_request: STALLED ucom0: ubsa_request: STALLED Can anyone help me to get this to work? Thanks and best regards, David ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"