Re: gEDA-user: Power relay question (Rob Butts)

2011-07-28 Thread Mike Bushroe
   I would use a microcontroller, for instance Atmel ATtiny ( [1]8 pin
   version) to replace the relays needed to keep track of 4 states, and an
   [2]L293 dual H-bridge motor driver to drive the two motors in forward
   and reverse directions. You would need 4 pins to control the two motors
   in two directions each, and 1 pin for the momentary contact switch. If
   you wanted two separate momentary contact switches, one start, the
   other to return, that would take all 6 I/O pins of the 8 pin chip. Or
   you could get a larger, 20 pin Attiny, or PIC from Microchip, or an
   Arduino or PickAxe or Basic Stamp to use for the controller.
   Mike

 This is a dumb question but I'm having a mental block.
 I have a 12 volt dc motor that I want to run from the push of a
 momentary
 pushbutton which will run until a limit switch gets hit. Digikey has
 a power
 latching relay PB1088-ND (cheap) that I can't tell if it actually
 latches
 once energized.  (I attached the relay document)
 Is relays and switches even the best/cheapest solution?
 Suggestions?
 Power:
 quantity of 2 12 volt batteries available
 Input:
 momenary 12 volt pushbutton #1
 Requirements:
 12 volt dc motor #1
 12 volt dc motor #2
 The application:
 Stage 1: momentary signal from pushbutton #1 starts motor #1 that
 runs until
 a limit switch is hit triggering stage 2
 Stage 2: motor #2 runs until another limit switch is hit and remains
 stable
 Stage 3: momentary signal from pushbutton #1 reverses the polarity
 of power
 to the motor #2 running it until back to it's start position and
 triggering
 stage 4
 Stage 4: reverse of the ploarity of the power to motor #1 running it
 until
 it is back to the start position
 Thanks for any suggestions if non I'll just wing it.
 --

   Burn the Land,  Boil the Sea,  You can't take the SKY from me!

References

   1. 
http://search.digikey.com/scripts/DkSearch/dksus.dll?Detailname=ATTINY13A-PU-ND
   2. 
http://search.digikey.com/scripts/DkSearch/dksus.dll?Detailname=497-1389-5-ND


___
geda-user mailing list
geda-user@moria.seul.org
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user


Re: gEDA-user: Power relay question (Rob Butts)

2011-07-28 Thread Rob Butts
   Thanks Mike, I'll look into this.

   On Thu, Jul 28, 2011 at 7:31 PM, Mike Bushroe [1]mbush...@gmail.com
   wrote:

   I would use a microcontroller, for instance Atmel ATtiny ( [1]8
 pin
   version) to replace the relays needed to keep track of 4 states,
 and an
   [2]L293 dual H-bridge motor driver to drive the two motors in
 forward
   and reverse directions. You would need 4 pins to control the two
 motors
   in two directions each, and 1 pin for the momentary contact
 switch. If
   you wanted two separate momentary contact switches, one start, the
   other to return, that would take all 6 I/O pins of the 8 pin chip.
 Or
   you could get a larger, 20 pin Attiny, or PIC from Microchip, or
 an
   Arduino or PickAxe or Basic Stamp to use for the controller.
   Mike
 This is a dumb question but I'm having a mental block.
 I have a 12 volt dc motor that I want to run from the push of a
 momentary
 pushbutton which will run until a limit switch gets hit. Digikey
 has
 a power
 latching relay PB1088-ND (cheap) that I can't tell if it
 actually
 latches
 once energized.  (I attached the relay document)
 Is relays and switches even the best/cheapest solution?
 Suggestions?
 Power:
 quantity of 2 12 volt batteries available
 Input:
 momenary 12 volt pushbutton #1
 Requirements:
 12 volt dc motor #1
 12 volt dc motor #2
 The application:
 Stage 1: momentary signal from pushbutton #1 starts motor #1
 that
 runs until
 a limit switch is hit triggering stage 2
 Stage 2: motor #2 runs until another limit switch is hit and
 remains
 stable
 Stage 3: momentary signal from pushbutton #1 reverses the
 polarity
 of power
 to the motor #2 running it until back to it's start position and
 triggering
 stage 4
 Stage 4: reverse of the ploarity of the power to motor #1
 running it
 until
 it is back to the start position
 Thanks for any suggestions if non I'll just wing it.
 --
   Burn the Land,  Boil the Sea,  You can't take the SKY from me!
 References
   1.
 [2]http://search.digikey.com/scripts/DkSearch/dksus.dll?Detailname=
 ATTINY13A-PU-ND
   2.
 [3]http://search.digikey.com/scripts/DkSearch/dksus.dll?Detailname=
 497-1389-5-ND
 ___
 geda-user mailing list
 [4]geda-user@moria.seul.org
 [5]http://www.seul.org/cgi-bin/mailman/listinfo/geda-user

References

   1. mailto:mbush...@gmail.com
   2. 
http://search.digikey.com/scripts/DkSearch/dksus.dll?Detailname=ATTINY13A-PU-ND
   3. 
http://search.digikey.com/scripts/DkSearch/dksus.dll?Detailname=497-1389-5-ND
   4. mailto:geda-user@moria.seul.org
   5. http://www.seul.org/cgi-bin/mailman/listinfo/geda-user


___
geda-user mailing list
geda-user@moria.seul.org
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user