Re: Generic Device Names and FDR
Just an FYI and for future information in case anyone else runs into the same problem. I redid the input tape dd and the FDR job ran: //TAPE1 DD DSN=FDRABR.VOPTSO1.C1061204, // VOL=(,RETAIN,,1,SER=(700319)), // UNIT=JAGR, // DISP=(OLD,KEEP) >>> Howard Rifkind <[EMAIL PROTECTED]> 10/30/2008 3:48 PM >>> Spoke with them for about 30 minutes...they think it might have something to with the Tape manager ... RMM but that's as far as we got. >>> "Cebell, David" <[EMAIL PROTECTED]> 10/30/2008 3:38 PM >>> Innovations has wonder Tech Support help. Did you run this by them? -Original Message- From: IBM Mainframe Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Howard Rifkind Sent: Thursday, October 30, 2008 2:25 PM To: IBM-MAIN@BAMA.UA.EDU Subject: Generic Device Names and FDR I'm trying to use the FDRABR scratch facility to restore a deleted dataset. An FDR print report showed that the dataset had been properly backed up and all the information needed appeared to be in the report for the indicated dataset. However I can't seem to be able to get the job to run due to not being able to mount the indicated tape (for input) on a 3592 which is the device type the back up tape was created on. When run, the job wants to mount the tape on device 580...the 580's are 3590 and the 700's are 3592's. The snip below is from the HCD. Devices Device Type 0580,48 3590 0710,16 3590 When just wanting to allocate a 3590 I specify unit=hcrt and get a 3590. I can't seem to be able to get a 3592 no matter what I do. tried: unit=710 unit=/710 unit=0710 unit=/0710 unit=HCRT and so on. Where in the system would something like HCRT be defined...couldn't find in HCD or was looking in the wring place. Running the job with something like unit=710 gives me the follow error: E18823X RESTORE TAPE1 ALLOCATION FAILED A NON-LIBRARY REQUEST SPECIFIED A LIBRARY DEVICE 0710 Any ideas or suggestions will be appreciated. Thanks. _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
Re: Generic Device Names and FDR
Howard, >From the fine manual through QuikRef -;-) NOT ENOUGH NON-SYSTEM MANAGED VOLUMES ELIGIBLE A request was made for a volume that SMS does not manage. There are not enough eligible volumes or eligible devices to satisfy the request. Note that for tapes, this could mean that there are no tape drives available outside of the Automated Tape Library, or that the SMS-managed tape volume being requested is not currently in the library (that is, it has been ejected), and the user exit for Volume Not in Library (CBRUXVNL) has not been implemented. Is the tape in the library and is a drive of the correct type online, or is the tape perhaps checked out to offsite? We send quite a few of our FDR tapes to offsite storage... Linda Mooney -- Original message -- From: Howard Rifkind <[EMAIL PROTECTED]> > Got it... > > Just where everyone said it would be calls it JARG > > Used that name in the Unit=JARG and got the following message: > > IEF343I - NOT ENOUGH NON-SYSTEM MANAGED VOLUMES ELIGIBLE > > How can I resolve this? > > Thanks > > > >>> "Field, Alan C." 10/30/2008 3:58 PM >>> > Howard, these might be defined in the EDT section of the OS configs. > > Use the HCD panels to look or select option 3 and print the OS -> EDT > reports. > > If you have SMS then the esoteric names might be being > intercepted/interpreted by the ACS routines. Talk to the Stg Admins for > that. > > Alan > > -Original Message- > From: IBM Mainframe Discussion List [mailto:[EMAIL PROTECTED] On > Behalf Of Howard Rifkind > > Subject: Generic Device Names and FDR > > I'm trying to use the FDRABR scratch facility to restore a deleted > dataset. > > An FDR print report showed that the dataset had been properly backed up > and all the information needed appeared to be in the report for the > indicated dataset. > > However I can't seem to be able to get the job to run due to not being > able to mount the indicated tape (for input) on a 3592 which is the > device type the back up tape was created on. > > When run, the job wants to mount the tape on device 580...the 580's are > 3590 and the 700's are 3592's. > > The snip below is from the HCD. > > Devices Device Type > 0580,48 3590 > 0710,16 3590 > > When just wanting to allocate a 3590 I specify unit=hcrt and get a 3590. > > I can't seem to be able to get a 3592 no matter what I do. tried: > > unit=710 > unit=/710 > unit=0710 > unit=/0710 > unit=HCRT and so on. > > Where in the system would something like HCRT be defined...couldn't find > in HCD or was looking in the wring place. > > Running the job with something like unit=710 gives me the follow error: > > E18823X RESTORE TAPE1 ALLOCATION FAILED > A NON-LIBRARY REQUEST SPECIFIED A LIBRARY DEVICE 0710 > > Any ideas or suggestions will be appreciated. > > Thanks. > > > -- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO > Search the archives at http://bama.ua.edu/archives/ibm-main.html > > > _ > LEGAL NOTICE > Unless expressly stated otherwise, this message is confidential > and may be privileged. It is intended for the addressee(s) only. > Access to this E-mail by anyone else is unauthorized. > If you are not an addressee, any disclosure or copying of the > contents of this E-mail or any action taken (or not taken) in > reliance on it is unauthorized and may be unlawful. If you are not an > addressee, please inform the sender immediately, then delete this > message and empty from your trash. > > > -- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO > Search the archives at http://bama.ua.edu/archives/ibm-main.html > -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
Re: Generic Device Names and FDR
Got it... Just where everyone said it would be calls it JARG Used that name in the Unit=JARG and got the following message: IEF343I - NOT ENOUGH NON-SYSTEM MANAGED VOLUMES ELIGIBLE How can I resolve this? Thanks >>> "Field, Alan C." <[EMAIL PROTECTED]> 10/30/2008 3:58 PM >>> Howard, these might be defined in the EDT section of the OS configs. Use the HCD panels to look or select option 3 and print the OS -> EDT reports. If you have SMS then the esoteric names might be being intercepted/interpreted by the ACS routines. Talk to the Stg Admins for that. Alan -Original Message- From: IBM Mainframe Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Howard Rifkind Subject: Generic Device Names and FDR I'm trying to use the FDRABR scratch facility to restore a deleted dataset. An FDR print report showed that the dataset had been properly backed up and all the information needed appeared to be in the report for the indicated dataset. However I can't seem to be able to get the job to run due to not being able to mount the indicated tape (for input) on a 3592 which is the device type the back up tape was created on. When run, the job wants to mount the tape on device 580...the 580's are 3590 and the 700's are 3592's. The snip below is from the HCD. Devices Device Type 0580,48 3590 0710,16 3590 When just wanting to allocate a 3590 I specify unit=hcrt and get a 3590. I can't seem to be able to get a 3592 no matter what I do. tried: unit=710 unit=/710 unit=0710 unit=/0710 unit=HCRT and so on. Where in the system would something like HCRT be defined...couldn't find in HCD or was looking in the wring place. Running the job with something like unit=710 gives me the follow error: E18823X RESTORE TAPE1 ALLOCATION FAILED A NON-LIBRARY REQUEST SPECIFIED A LIBRARY DEVICE 0710 Any ideas or suggestions will be appreciated. Thanks. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
Re: Generic Device Names and FDR
Howard, these might be defined in the EDT section of the OS configs. Use the HCD panels to look or select option 3 and print the OS -> EDT reports. If you have SMS then the esoteric names might be being intercepted/interpreted by the ACS routines. Talk to the Stg Admins for that. Alan -Original Message- From: IBM Mainframe Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Howard Rifkind Subject: Generic Device Names and FDR I'm trying to use the FDRABR scratch facility to restore a deleted dataset. An FDR print report showed that the dataset had been properly backed up and all the information needed appeared to be in the report for the indicated dataset. However I can't seem to be able to get the job to run due to not being able to mount the indicated tape (for input) on a 3592 which is the device type the back up tape was created on. When run, the job wants to mount the tape on device 580...the 580's are 3590 and the 700's are 3592's. The snip below is from the HCD. Devices Device Type 0580,48 3590 0710,16 3590 When just wanting to allocate a 3590 I specify unit=hcrt and get a 3590. I can't seem to be able to get a 3592 no matter what I do. tried: unit=710 unit=/710 unit=0710 unit=/0710 unit=HCRT and so on. Where in the system would something like HCRT be defined...couldn't find in HCD or was looking in the wring place. Running the job with something like unit=710 gives me the follow error: E18823X RESTORE TAPE1 ALLOCATION FAILED A NON-LIBRARY REQUEST SPECIFIED A LIBRARY DEVICE 0710 Any ideas or suggestions will be appreciated. Thanks. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
Re: Generic Device Names and FDR
D u,tape,,,128 should show you all of these devices -Original Message- From: IBM Mainframe Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Howard Rifkind Sent: Thursday, October 30, 2008 2:49 PM To: IBM-MAIN@BAMA.UA.EDU Subject: Re: Generic Device Names and FDR Spoke with them for about 30 minutes...they think it might have something to with the Tape manager ... RMM but that's as far as we got. >>> "Cebell, David" <[EMAIL PROTECTED]> 10/30/2008 3:38 PM >>> Innovations has wonder Tech Support help. Did you run this by them? -Original Message- From: IBM Mainframe Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Howard Rifkind Sent: Thursday, October 30, 2008 2:25 PM To: IBM-MAIN@BAMA.UA.EDU Subject: Generic Device Names and FDR I'm trying to use the FDRABR scratch facility to restore a deleted dataset. An FDR print report showed that the dataset had been properly backed up and all the information needed appeared to be in the report for the indicated dataset. However I can't seem to be able to get the job to run due to not being able to mount the indicated tape (for input) on a 3592 which is the device type the back up tape was created on. When run, the job wants to mount the tape on device 580...the 580's are 3590 and the 700's are 3592's. The snip below is from the HCD. Devices Device Type 0580,48 3590 0710,16 3590 When just wanting to allocate a 3590 I specify unit=hcrt and get a 3590. I can't seem to be able to get a 3592 no matter what I do. tried: unit=710 unit=/710 unit=0710 unit=/0710 unit=HCRT and so on. Where in the system would something like HCRT be defined...couldn't find in HCD or was looking in the wring place. Running the job with something like unit=710 gives me the follow error: E18823X RESTORE TAPE1 ALLOCATION FAILED A NON-LIBRARY REQUEST SPECIFIED A LIBRARY DEVICE 0710 Any ideas or suggestions will be appreciated. Thanks. _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
Re: Generic Device Names and FDR
Spoke with them for about 30 minutes...they think it might have something to with the Tape manager ... RMM but that's as far as we got. >>> "Cebell, David" <[EMAIL PROTECTED]> 10/30/2008 3:38 PM >>> Innovations has wonder Tech Support help. Did you run this by them? -Original Message- From: IBM Mainframe Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Howard Rifkind Sent: Thursday, October 30, 2008 2:25 PM To: IBM-MAIN@BAMA.UA.EDU Subject: Generic Device Names and FDR I'm trying to use the FDRABR scratch facility to restore a deleted dataset. An FDR print report showed that the dataset had been properly backed up and all the information needed appeared to be in the report for the indicated dataset. However I can't seem to be able to get the job to run due to not being able to mount the indicated tape (for input) on a 3592 which is the device type the back up tape was created on. When run, the job wants to mount the tape on device 580...the 580's are 3590 and the 700's are 3592's. The snip below is from the HCD. Devices Device Type 0580,48 3590 0710,16 3590 When just wanting to allocate a 3590 I specify unit=hcrt and get a 3590. I can't seem to be able to get a 3592 no matter what I do. tried: unit=710 unit=/710 unit=0710 unit=/0710 unit=HCRT and so on. Where in the system would something like HCRT be defined...couldn't find in HCD or was looking in the wring place. Running the job with something like unit=710 gives me the follow error: E18823X RESTORE TAPE1 ALLOCATION FAILED A NON-LIBRARY REQUEST SPECIFIED A LIBRARY DEVICE 0710 Any ideas or suggestions will be appreciated. Thanks. _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
Re: Generic Device Names and FDR
Innovations has wonder Tech Support help. Did you run this by them? -Original Message- From: IBM Mainframe Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Howard Rifkind Sent: Thursday, October 30, 2008 2:25 PM To: IBM-MAIN@BAMA.UA.EDU Subject: Generic Device Names and FDR I'm trying to use the FDRABR scratch facility to restore a deleted dataset. An FDR print report showed that the dataset had been properly backed up and all the information needed appeared to be in the report for the indicated dataset. However I can't seem to be able to get the job to run due to not being able to mount the indicated tape (for input) on a 3592 which is the device type the back up tape was created on. When run, the job wants to mount the tape on device 580...the 580's are 3590 and the 700's are 3592's. The snip below is from the HCD. Devices Device Type 0580,48 3590 0710,16 3590 When just wanting to allocate a 3590 I specify unit=hcrt and get a 3590. I can't seem to be able to get a 3592 no matter what I do. tried: unit=710 unit=/710 unit=0710 unit=/0710 unit=HCRT and so on. Where in the system would something like HCRT be defined...couldn't find in HCD or was looking in the wring place. Running the job with something like unit=710 gives me the follow error: E18823X RESTORE TAPE1 ALLOCATION FAILED A NON-LIBRARY REQUEST SPECIFIED A LIBRARY DEVICE 0710 Any ideas or suggestions will be appreciated. Thanks. _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
Generic Device Names and FDR
I'm trying to use the FDRABR scratch facility to restore a deleted dataset. An FDR print report showed that the dataset had been properly backed up and all the information needed appeared to be in the report for the indicated dataset. However I can't seem to be able to get the job to run due to not being able to mount the indicated tape (for input) on a 3592 which is the device type the back up tape was created on. When run, the job wants to mount the tape on device 580...the 580's are 3590 and the 700's are 3592's. The snip below is from the HCD. Devices Device Type 0580,48 3590 0710,16 3590 When just wanting to allocate a 3590 I specify unit=hcrt and get a 3590. I can't seem to be able to get a 3592 no matter what I do. tried: unit=710 unit=/710 unit=0710 unit=/0710 unit=HCRT and so on. Where in the system would something like HCRT be defined...couldn't find in HCD or was looking in the wring place. Running the job with something like unit=710 gives me the follow error: E18823X RESTORE TAPE1 ALLOCATION FAILED A NON-LIBRARY REQUEST SPECIFIED A LIBRARY DEVICE 0710 Any ideas or suggestions will be appreciated. Thanks. _ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. -- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html