KR> Re: rain water on my fusalage floor
I need some advice on how to take care of rain water on my fuslage floor. Thanks for all the feedback about my wet floor. By last evening the najority of the wet floor had dried already from the wind blowing across it all day. - Original Message - From: "Tony Wright" To: "KRnet" Sent: Sunday, September 11, 2011 2:33:19 PM Subject: Re: KR> Re: rain water on my fusalage floor I would not use any heat!!! Air dry only. You do not want to remove the natural moisture of the wood, as this will cause fibers to shrink too much. Air movement is a good thing to help it dry out, properly. My guess is that all will be fine as long as the water is removed and the boat is naturally allowed to dry. Good luck. Tony Wright ATP - Original Message - From: "M&C" To: "KRnet" Sent: Sunday, September 11, 2011 2:18 PM Subject: Re: KR> Re: rain water on my fusalage floor It wouldn't hurt to put a small ceramic heater (on low heat) in the fuselage just to keep the air dry around it so it can evaporate. Mike Turner Edgewood NM - Original Message - From: smwood To: kr...@mylist.net Sent: Sunday, September 11, 2011 11:07 AM Subject: KR> Re: rain water on my fusalage floor I need some advice on how to take care of rain water on my fuslage floor. I purchased John Godwins KR2S project in South Carolina last Wednesday and had to travel back to New York through the hurricane rain storms. Unfortunataely i took on some rain water last night driving through Pensylvania. I immediately soaked up the little bit of standing water close to the spruce cross members.I think air drying it will be best. I think if i blow dry it with a heat gun it might warp and delaminate. any suggestions appreciated, Joe Same thing happened to me a few years ago. Wound up with about 5/8" of water in each bay on the fuselage floor. Prior to that I had painted the inside of the fuselage with thinned epoxy. So, I was able to mop up the water with a sponge and rags. The outside plywood had not been painted. The bare mahogany showed some water stain but no warpage after air drying. The aircraft grade plywood has waterproof glue. Most epoxy glues are also waterproof, but the uncoated lumber can soak up the water and cause issues with uneven expansion and then contraction when it dries out. Use great care with the heat gun: you might overheat the glue joints and soften the epoxy. That could do more damage than water soaking. Recommend you wipe up the visible water soon as possible. Then air dry with with lots of ventilation with a fan or two. Sid Wood Tri-gear KR-2 N6242 Mechanicsville, MD, USA smw...@md.metrocast.net ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html __ Information from ESET NOD32 Antivirus, version of virus signature database 6454 (20110911) __ The message was checked by ESET NOD32 Antivirus. http://www.eset.com __ Information from ESET NOD32 Antivirus, version of virus signature database 6455 (20110911) __ The message was checked by ESET NOD32 Antivirus. http://www.eset.com ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Re: rain water on my fusalage floor
I would not use any heat!!! Air dry only. You do not want to remove the natural moisture of the wood, as this will cause fibers to shrink too much. Air movement is a good thing to help it dry out, properly. My guess is that all will be fine as long as the water is removed and the boat is naturally allowed to dry. Good luck. Tony Wright ATP - Original Message - From: "M&C" To: "KRnet" Sent: Sunday, September 11, 2011 2:18 PM Subject: Re: KR> Re: rain water on my fusalage floor It wouldn't hurt to put a small ceramic heater (on low heat) in the fuselage just to keep the air dry around it so it can evaporate. Mike Turner Edgewood NM - Original Message - From: smwood To: kr...@mylist.net Sent: Sunday, September 11, 2011 11:07 AM Subject: KR> Re: rain water on my fusalage floor I need some advice on how to take care of rain water on my fuslage floor. I purchased John Godwins KR2S project in South Carolina last Wednesday and had to travel back to New York through the hurricane rain storms. Unfortunataely i took on some rain water last night driving through Pensylvania. I immediately soaked up the little bit of standing water close to the spruce cross members.I think air drying it will be best. I think if i blow dry it with a heat gun it might warp and delaminate. any suggestions appreciated, Joe Same thing happened to me a few years ago. Wound up with about 5/8" of water in each bay on the fuselage floor. Prior to that I had painted the inside of the fuselage with thinned epoxy. So, I was able to mop up the water with a sponge and rags. The outside plywood had not been painted. The bare mahogany showed some water stain but no warpage after air drying. The aircraft grade plywood has waterproof glue. Most epoxy glues are also waterproof, but the uncoated lumber can soak up the water and cause issues with uneven expansion and then contraction when it dries out. Use great care with the heat gun: you might overheat the glue joints and soften the epoxy. That could do more damage than water soaking. Recommend you wipe up the visible water soon as possible. Then air dry with with lots of ventilation with a fan or two. Sid Wood Tri-gear KR-2 N6242 Mechanicsville, MD, USA smw...@md.metrocast.net ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html __ Information from ESET NOD32 Antivirus, version of virus signature database 6454 (20110911) __ The message was checked by ESET NOD32 Antivirus. http://www.eset.com __ Information from ESET NOD32 Antivirus, version of virus signature database 6455 (20110911) __ The message was checked by ESET NOD32 Antivirus. http://www.eset.com
KR> Re: rain water on my fusalage floor
It wouldn't hurt to put a small ceramic heater (on low heat) in the fuselage just to keep the air dry around it so it can evaporate. Mike Turner Edgewood NM - Original Message - From: smwood To: kr...@mylist.net Sent: Sunday, September 11, 2011 11:07 AM Subject: KR> Re: rain water on my fusalage floor I need some advice on how to take care of rain water on my fuslage floor. I purchased John Godwins KR2S project in South Carolina last Wednesday and had to travel back to New York through the hurricane rain storms. Unfortunataely i took on some rain water last night driving through Pensylvania. I immediately soaked up the little bit of standing water close to the spruce cross members.I think air drying it will be best. I think if i blow dry it with a heat gun it might warp and delaminate. any suggestions appreciated, Joe Same thing happened to me a few years ago. Wound up with about 5/8" of water in each bay on the fuselage floor. Prior to that I had painted the inside of the fuselage with thinned epoxy. So, I was able to mop up the water with a sponge and rags. The outside plywood had not been painted. The bare mahogany showed some water stain but no warpage after air drying. The aircraft grade plywood has waterproof glue. Most epoxy glues are also waterproof, but the uncoated lumber can soak up the water and cause issues with uneven expansion and then contraction when it dries out. Use great care with the heat gun: you might overheat the glue joints and soften the epoxy. That could do more damage than water soaking. Recommend you wipe up the visible water soon as possible. Then air dry with with lots of ventilation with a fan or two. Sid Wood Tri-gear KR-2 N6242 Mechanicsville, MD, USA smw...@md.metrocast.net ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Re: rain water on my fusalage floor
I need some advice on how to take care of rain water on my fuslage floor. I purchased John Godwins KR2S project in South Carolina last Wednesday and had to travel back to New York through the hurricane rain storms. Unfortunataely i took on some rain water last night driving through Pensylvania. I immediately soaked up the little bit of standing water close to the spruce cross members.I think air drying it will be best. I think if i blow dry it with a heat gun it might warp and delaminate. any suggestions appreciated, Joe Same thing happened to me a few years ago. Wound up with about 5/8" of water in each bay on the fuselage floor. Prior to that I had painted the inside of the fuselage with thinned epoxy. So, I was able to mop up the water with a sponge and rags. The outside plywood had not been painted. The bare mahogany showed some water stain but no warpage after air drying. The aircraft grade plywood has waterproof glue. Most epoxy glues are also waterproof, but the uncoated lumber can soak up the water and cause issues with uneven expansion and then contraction when it dries out. Use great care with the heat gun: you might overheat the glue joints and soften the epoxy. That could do more damage than water soaking. Recommend you wipe up the visible water soon as possible. Then air dry with with lots of ventilation with a fan or two. Sid Wood Tri-gear KR-2 N6242 Mechanicsville, MD, USA smw...@md.metrocast.net
