Re: Headstock coupling question
On Sun, Nov 26, 2017 at 7:56 PM 'Curt George' via Legacy Ornamental Mills < legacy-ornamental-mills@googlegroups.com> wrote: > $29.00 is what Legacy was selling them for. You will have to call and > ask, if they are still making them ((( ASK FOR Cindy!!!))) > > C.A.G.thanks guys. I guess one side wouldn’t HAVE to be threaded but if i > can find a threaded one I will get it. I was milling coves in a four sided > flat leg and having a hard time getting it exact so I could “divide” it > into 4 sections > Joe > > > On Sunday, November 26, 2017 8:44 PM, russ veinot > wrote: > > > nice information gathering :>) you made my life easier. anyone know how > much one is from Legacy? is it available? > > On Sunday, November 26, 2017 at 5:05:37 PM UTC-6, Joe Gassen wrote: > > Sorry to ask but I can’t find the answer. Some time back there was a > coupler discussed that would thread on my headstock 1”x8 and also clamp to > 2 MT to allow precise alignment when positioning , say a 4 sided spindle > and by adjusting set screws allow that opportunity. Anyone have a link to > it or the plans to make one? Seems like it looked similar to two of the > stop collars used on the leadscrew. Thx > Joe > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Headstock coupling question
Sorry to ask but I can’t find the answer. Some time back there was a coupler discussed that would thread on my headstock 1”x8 and also clamp to 2 MT to allow precise alignment when positioning , say a 4 sided spindle and by adjusting set screws allow that opportunity. Anyone have a link to it or the plans to make one? Seems like it looked similar to two of the stop collars used on the leadscrew. Thx Joe -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: rememberance day
Amen On Fri, Nov 10, 2017 at 9:16 PM Bill Bulkeley wrote: > This is not legacy but important to me . > > Its remembrance day here today the 11th month at 11am we stop for a > minute silence to remember all our fallen Soldiers and as usual i only saw > me do it, I do hate what the world has become. Here is the song I always > like to play on this day > > https://www.youtube.com/watch?v=2kX_3y3u5Uo > > > > Bill > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: New video on youtube
Great video with several tips. Thx On Tue, Nov 7, 2017 at 2:21 PM, Russ Veinot wrote: > !!!*** NEW VIDEO ***!!! > > > > > > My new video is now out at https://www.youtube.com/watch?v=m5pKXXZCKXY > > > > It’s about DIY faceplates for the LOM. I show how easy to make and what > to watch out for. There is special attention to custom faceplates and tips > for the LOM. > > > > Russ > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@ > googlegroups.com. > Visit this group at https://groups.google.com/ > group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
Faceplate great idea but i'll need 4 for the many steps I do.. On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot wrote: > Excellent Suggestion !!?!! > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Michael Kratky > *Sent:* Sunday, November 05, 2017 8:18 AM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* RE: Need LOM dogs and split nut > > > > There’s always a lathe faceplate: > > > > [image: https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg] > > > > > > *From:* legacy-ornamental-mills@googlegroups.com [ > mailto:legacy-ornamental-mills@googlegroups.com > ] *On Behalf Of *Joe G > *Sent:* Saturday, November 04, 2017 10:12 PM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: Need LOM dogs and split nut > > > > [image: Inline image 1]I have the threaded headstock with looks like a #2 > MT > > I do have 1" X 8 thread check but it only opens to 3" I think. The legs I > were turning for a table are 4" and 5" Sq at top[image: Inline image 2] > > > > On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot wrote: > > BUY EXTRA !! :>) > > Oh, I already said that. Does the headstock have a threaded head for > adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to > my LOM. Does it have the #1 morse taper headstock? > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Joe Gassen > *Sent:* Saturday, November 04, 2017 7:47 PM > *To:* Legacy Ornamental Mills > > > *Subject:* Re: Need LOM dogs and split nut > > > > Thanks Tim, Ill call back Monday! > > > > On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: > > Call Legacy back and ask for Cindy. She is in charge of the parts for the > manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot > wrote: > > > > BUY EXTRA !! :>) > > > > > > > > From: legacy-orna...@googlegroups.com [mailto:legacy-ornamental- > mi...@googlegroups.com ] On > Behalf Of Joe G > > Sent: Friday, November 03, 2017 6:51 PM > > To: legacy-orna...@googlegroups.com > > Subject: Re: Need LOM dogs and split nut > > > > > > > > Thanks guys for the help. I called Legacy and the man that answered said > he would have someone call me back and he thought they had the parts. > > > > No call yet..fingers crossed! > > > > > > > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE > wrote: > > > > Hello again Joe > > > > > > > > do you still have the old split nut? Its just the upper half you need? > If so I may be some help for you. I own a home made tap for the 5/8 x 4 > acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can > cut it to fit... > > > > Please let me know if you still need help on this? > > > > more latter. > > > > > > > > C.A.G. > > > > > > > > _ > > > > From: "Joe Gassen" > > To: "Legacy Ornamental Mills" > > Sent: Friday, November 3, 2017 12:07:33 PM > > Subject: Need LOM dogs and split nut > > > > > > > > I sent an e-mail but later found this board. > > > > I have an older steel rail LOM and have recently begun to use it again. > > > > I need at least two of the 4 prong dogs that fit the headstock mad will > also need a split nut in the future for the 5/8 acme. > > > > Any help will be appreciated since I see Legacy no longer supports the > older LOM s and have also taken down the old training videos. > > > > Thx all > > > > > > > > Joe > > > > > > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@ > googlegroups.com. > Visit this group at https://groups.google.com/ > group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, se
Re: Need LOM dogs and split nut
I was playing with a design with the spiral but decided the spiral was too fancy for a farm table. Also the "beads" below the spiral were too big so I went with the plain taper. Sure wish I could score the old Legacy "design kit" I have trouble visualizing what a cutter looks like with partial or full cutting depth. On Sat, Nov 4, 2017 at 9:12 PM, Joe G wrote: > [image: Inline image 1]I have the threaded headstock with looks like a #2 > MT > I do have 1" X 8 thread check but it only opens to 3" I think. The legs I > were turning for a table are 4" and 5" Sq at top[image: Inline image 2] > > On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot wrote: > >> BUY EXTRA !! :>) >> >> Oh, I already said that. Does the headstock have a threaded head for >> adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to >> my LOM. Does it have the #1 morse taper headstock? >> >> >> >> *From:* legacy-ornamental-mills@googlegroups.com [mailto: >> legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Joe Gassen >> *Sent:* Saturday, November 04, 2017 7:47 PM >> *To:* Legacy Ornamental Mills >> >> *Subject:* Re: Need LOM dogs and split nut >> >> >> >> Thanks Tim, Ill call back Monday! >> >> >> >> On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: >> >> Call Legacy back and ask for Cindy. She is in charge of the parts for >> the manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ >> Veinot wrote: >> > >> > BUY EXTRA !! :>) >> > >> > >> > >> > From: legacy-orna...@googlegroups.com [mailto:legacy-ornamental-mill >> s...@googlegroups.com] On Behalf Of Joe G >> > Sent: Friday, November 03, 2017 6:51 PM >> > To: legacy-orna...@googlegroups.com >> > Subject: Re: Need LOM dogs and split nut >> > >> > >> > >> > Thanks guys for the help. I called Legacy and the man that answered >> said he would have someone call me back and he thought they had the parts. >> > >> > No call yet..fingers crossed! >> > >> > >> > >> > >> > >> > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE >> wrote: >> > >> > Hello again Joe >> > >> > >> > >> > do you still have the old split nut? Its just the upper half you need? >> If so I may be some help for you. I own a home made tap for the 5/8 x 4 >> acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can >> cut it to fit... >> > >> > Please let me know if you still need help on this? >> > >> > more latter. >> > >> > >> > >> > C.A.G. >> > >> > >> > >> > _ >> > >> > From: "Joe Gassen" >> > To: "Legacy Ornamental Mills" >> > Sent: Friday, November 3, 2017 12:07:33 PM >> > Subject: Need LOM dogs and split nut >> > >> > >> > >> > I sent an e-mail but later found this board. >> > >> > I have an older steel rail LOM and have recently begun to use it again. >> > >> > I need at least two of the 4 prong dogs that fit the headstock mad will >> also need a split nut in the future for the 5/8 acme. >> > >> > Any help will be appreciated since I see Legacy no longer supports the >> older LOM s and have also taken down the old training videos. >> > >> > Thx all >> > >> > >> > >> > Joe >> > >> > >> > >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To post to this group, send email to legacy-ornamental-mills@google >> groups.com. >> Visit this group at https://groups.google.com/grou >> p/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To post to this group, send email to legacy-ornamental-mills@google >> groups.com. >> Visit this group at https://groups.google.com/grou >> p/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
[image: Inline image 1]I have the threaded headstock with looks like a #2 MT I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were turning for a table are 4" and 5" Sq at top[image: Inline image 2] On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot wrote: > BUY EXTRA !! :>) > > Oh, I already said that. Does the headstock have a threaded head for > adding a 4 jaw chuck? I rarely use my LOM dogs anymore since adding one to > my LOM. Does it have the #1 morse taper headstock? > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Joe Gassen > *Sent:* Saturday, November 04, 2017 7:47 PM > *To:* Legacy Ornamental Mills > > *Subject:* Re: Need LOM dogs and split nut > > > > Thanks Tim, Ill call back Monday! > > > > On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: > > Call Legacy back and ask for Cindy. She is in charge of the parts for the > manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot > wrote: > > > > BUY EXTRA !! :>) > > > > > > > > From: legacy-orna...@googlegroups.com [mailto:legacy-ornamental-mill > s...@googlegroups.com] On Behalf Of Joe G > > Sent: Friday, November 03, 2017 6:51 PM > > To: legacy-orna...@googlegroups.com > > Subject: Re: Need LOM dogs and split nut > > > > > > > > Thanks guys for the help. I called Legacy and the man that answered said > he would have someone call me back and he thought they had the parts. > > > > No call yet..fingers crossed! > > > > > > > > > > > > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE > wrote: > > > > Hello again Joe > > > > > > > > do you still have the old split nut? Its just the upper half you need? > If so I may be some help for you. I own a home made tap for the 5/8 x 4 > acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can > cut it to fit... > > > > Please let me know if you still need help on this? > > > > more latter. > > > > > > > > C.A.G. > > > > > > > > _ > > > > From: "Joe Gassen" > > To: "Legacy Ornamental Mills" > > Sent: Friday, November 3, 2017 12:07:33 PM > > Subject: Need LOM dogs and split nut > > > > > > > > I sent an e-mail but later found this board. > > > > I have an older steel rail LOM and have recently begun to use it again. > > > > I need at least two of the 4 prong dogs that fit the headstock mad will > also need a split nut in the future for the 5/8 acme. > > > > Any help will be appreciated since I see Legacy no longer supports the > older LOM s and have also taken down the old training videos. > > > > Thx all > > > > > > > > Joe > > > > > > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@google > groups.com. > Visit this group at https://groups.google.com/grou > p/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@google > groups.com. > Visit this group at https://groups.google.com/grou > p/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
Thanks guys for the help. I called Legacy and the man that answered said he would have someone call me back and he thought they had the parts. No call yet..fingers crossed! On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE wrote: > Hello again Joe > > do you still have the old split nut? Its just the upper half you need? If > so I may be some help for you. I own a home made tap for the 5/8 x 4 acme > screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut > it to fit... > Please let me know if you still need help on this? > more latter. > > C.A.G. > > -- > *From: *"Joe Gassen" > *To: *"Legacy Ornamental Mills" > *Sent: *Friday, November 3, 2017 12:07:33 PM > *Subject: *Need LOM dogs and split nut > > I sent an e-mail but later found this board. > I have an older steel rail LOM and have recently begun to use it again. > I need at least two of the 4 prong dogs that fit the headstock mad will > also need a split nut in the future for the 5/8 acme. > Any help will be appreciated since I see Legacy no longer supports the > older LOM s and have also taken down the old training videos. > Thx all > > Joe > > 256-seven9seven too three 2 fore > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@ > googlegroups.com. > Visit this group at https://groups.google.com/ > group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@ > googlegroups.com. > Visit this group at https://groups.google.com/ > group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Need LOM dogs and split nut
On Fri, Nov 3, 2017 at 3:07 PM Russ Veinot wrote: > 5/8th acme was used on my 1200 with aluminum rails. They still sold the > split nut for mine (should be the same) as of a couple of months ago. Hope > this helps. > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Joe Gassen > *Sent:* Friday, November 03, 2017 11:08 AM > *To:* Legacy Ornamental Mills > *Subject:* Need LOM dogs and split nut > > Thanks!! I’ll try them > I sent an e-mail but later found this board. > > I have an older steel rail LOM and have recently begun to use it again. > > I need at least two of the 4 prong dogs that fit the headstock mad will > also need a split nut in the future for the 5/8 acme. > > Any help will be appreciated since I see Legacy no longer supports the > older LOM s and have also taken down the old training videos. > > Thx all > > > > Joe > > > > 256-seven9seven too three 2 fore > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Purchasing LOM dogs and split nut
I have dusted off (literally) the old steel rail LOM and trying to turn legs for tables. I only have 2 of the "dogs" that fit the headstock and need at least 2 more because I am doing 4 of these in steps and have to mount and remount the dogs. Also, while seeking things. I will need a split nut for the linear screw soon. If any of you have or produce these. please contact me. I see Legacy no longer supports my machine at all. Thx Joe -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
