Re: Vent cover
Hi Dexter Rare earth magnets come in handy for all sorts of jobs, a couple of screws washers depending on the place it's going to. A nice job on the vent cover looks good Regards Richard On Thursday, August 10, 2017 at 2:06:59 PM UTC+1, Dexter Bland wrote: > > I like the idea of the v-grove bit and it is not too late to do that. I'll > ask the homeowner about how to hold the cover on. However attached, > it needs to be removable. > Thanks for the suggestions. > > On Wednesday, August 9, 2017 at 10:46:05 PM UTC-5, Va Oak wrote: > >> Dexter, >> >> Very well done. GREAT job. Thanks for sharing. >> >> If you make another, give thought to flipping the board over and running >> a 60 degree V-groove bit down the centerline of each slot/vent opening. >> That will allow for a bit better airflow through the slots and reduce >> backpressure in the ducting. >> >> How are you securing it over the opening in the toe kick board? Rather >> than marring your beautiful work with screws, try either 3M Command Strips >> (pick one with only a few pounds of pull) or a strip of "hook & loop" >> (Velcro®) at each end. >> >> Just my 2 cent's worth. >> >> >> -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Vent cover
I like the idea of the v-grove bit and it is not too late to do that. I'll ask the homeowner about how to hold the cover on. However attached, it needs to be removable. Thanks for the suggestions. On Wednesday, August 9, 2017 at 10:46:05 PM UTC-5, Va Oak wrote: > Dexter, > > Very well done. GREAT job. Thanks for sharing. > > If you make another, give thought to flipping the board over and running a > 60 degree V-groove bit down the centerline of each slot/vent opening. That > will allow for a bit better airflow through the slots and reduce > backpressure in the ducting. > > How are you securing it over the opening in the toe kick board? Rather > than marring your beautiful work with screws, try either 3M Command Strips > (pick one with only a few pounds of pull) or a strip of "hook & loop" > (Velcro®) at each end. > > Just my 2 cent's worth. > > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
RE: Vent cover
Dexter,Very well done. GREAT job. Thanks for sharing.If you make another, give thought to flipping the board over and running a 60 degree V-groove bit down the centerline of each slot/vent opening. That will allow for a bit better airflow through the slots and reduce backpressure in the ducting. How are you securing it over the opening in the toe kick board? Rather than marring your beautiful work with screws, try either 3M Command Strips (pick one with only a few pounds of pull) or a strip of "hook & loop" (Velcro®) at each end.Just my 2 cent's worth.Mac-Original Message- From: Russ Veinot <ru...@yknotwood.com> Sent: Aug 9, 2017 6:48 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: Vent cover <zzz!--[if gte="" mso="" 9]=""> <zzz![endif]--><zzz!--[if gte="" mso="" 9]=""> <zzz![endif]-->My hat is off to you. I always enjoy a good flat milling project. Looks like that was fun to do. Would have made a great youtube video:>) From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Dexter BlandSent: Tuesday, August 08, 2017 8:08 AMTo: legacy-ornamental-millsSubject: Fwd: Vent cover This is a simple project I did last night. When you can't find what you need in the shape/size/type of wood, you make it yourself. I needed a air vent duct cover out of birch for a cabinet toe-kick and the Legacy made this project easy.Photo 1 - First you have to find your machine. It is under there somewhere.Photo 2 - Make/attach work surface to the rails.Photo 3 - Use router bit to square up the board.Photo 4 - Use the Mike Pung crank method to equally space the cuts.Photo 5 - Round-over the edges and sand.Photo 6 - Dado the edges to fit in the vent hole.I did not cut the board thinner just in case the cover gets kicked or hit with a vacuum. It is not a sexy project, but maybe this will spur some idea of some common thing you can make out of wood. db -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Vent cover
nice On Wed, Aug 9, 2017 at 5:48 PM, Russ Veinot <ru...@yknotwood.com> wrote: > My hat is off to you. I always enjoy a good flat milling project. Looks > like that was fun to do. Would have made a great youtube video:>) > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Dexter Bland > *Sent:* Tuesday, August 08, 2017 8:08 AM > *To:* legacy-ornamental-mills > *Subject:* Fwd: Vent cover > > > > This is a simple project I did last night. When you can't find what you > need in the shape/size/type of wood, you make it yourself. I needed a air > vent duct cover out of birch for a cabinet toe-kick and the Legacy made > this project easy. > > Photo 1 - First you have to find your machine. It is under there > somewhere. > > Photo 2 - Make/attach work surface to the rails. > > Photo 3 - Use router bit to square up the board. > > Photo 4 - Use the Mike Pung crank method to equally space the cuts. > > Photo 5 - Round-over the edges and sand. > > Photo 6 - Dado the edges to fit in the vent hole. > > I did not cut the board thinner just in case the cover gets kicked or hit > with a vacuum. It is not a sexy project, but maybe this will spur some idea > of some common thing you can make out of wood. > > > > db > > > > > > > > > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@ > googlegroups.com. > Visit this group at https://groups.google.com/ > group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@ > googlegroups.com. > Visit this group at https://groups.google.com/ > group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
RE: Vent cover
My hat is off to you. I always enjoy a good flat milling project. Looks like that was fun to do. Would have made a great youtube video:>) From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Dexter Bland Sent: Tuesday, August 08, 2017 8:08 AM To: legacy-ornamental-mills Subject: Fwd: Vent cover This is a simple project I did last night. When you can't find what you need in the shape/size/type of wood, you make it yourself. I needed a air vent duct cover out of birch for a cabinet toe-kick and the Legacy made this project easy. Photo 1 - First you have to find your machine. It is under there somewhere. Photo 2 - Make/attach work surface to the rails. Photo 3 - Use router bit to square up the board. Photo 4 - Use the Mike Pung crank method to equally space the cuts. Photo 5 - Round-over the edges and sand. Photo 6 - Dado the edges to fit in the vent hole. I did not cut the board thinner just in case the cover gets kicked or hit with a vacuum. It is not a sexy project, but maybe this will spur some idea of some common thing you can make out of wood. db -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
RE: Vent cover
It’s a nice job I have never made a vent cover before and the legacy made it easy Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Dexter Bland Sent: Tuesday, 8 August 2017 11:08 PM To: legacy-ornamental-mills Subject: Fwd: Vent cover This is a simple project I did last night. When you can't find what you need in the shape/size/type of wood, you make it yourself. I needed a air vent duct cover out of birch for a cabinet toe-kick and the Legacy made this project easy. Photo 1 - First you have to find your machine. It is under there somewhere. Photo 2 - Make/attach work surface to the rails. Photo 3 - Use router bit to square up the board. Photo 4 - Use the Mike Pung crank method to equally space the cuts. Photo 5 - Round-over the edges and sand. Photo 6 - Dado the edges to fit in the vent hole. I did not cut the board thinner just in case the cover gets kicked or hit with a vacuum. It is not a sexy project, but maybe this will spur some idea of some common thing you can make out of wood. db -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> Virus-free. <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> www.avg.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.