TULIP driver broken

2001-04-24 Thread Ian Zink 

Well it would appear the tulip driver regressed from 2.4.2-ac22 and
2.4.3. (2.4.3-ac12 isn't working either) Once again, my tulip card just
spews carrier errors and doesn't even get a link light.

If someone could point me to a patch I would appreciate it. I have
attached any pretient information below.


Thanks, Ian Zink


Linux zforce 2.4.3-ac12 #5 Tue Apr 24 02:49:03 CDT 2001 i686 unknown

  Bus  0, device  11, function  0:
Ethernet controller: Digital Equipment Corporation DECchip 21140
[FasterNet]
 (rev 32).
  IRQ 10.
  Master Capable.  Latency=32.  Min Gnt=20.Max Lat=40.
  I/O at 0xb000 [0xb07f].
  Non-prefetchable 32 bit memory at 0xe080 [0xe080007f].

eth0  Link encap:Ethernet  HWaddr 00:00:C0:41:99:E9
  inet addr:10.1.1.1  Bcast:10.1.1.255  Mask:255.255.255.0
  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  TX packets:0 errors:243 dropped:0 overruns:0 carrier:243
  collisions:0 txqueuelen:100
  RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
  Interrupt:10 Base address:0xb000

Linux version 2.4.3-ac12 (root@zforce) (gcc version 2.95.4 20010319
(Debian prer
elease)) #5 Tue Apr 24 02:49:03 CDT 2001


Linux Tulip driver version 0.9.14e (April 20, 2001)
PCI: Found IRQ 10 for device 00:0b.0
tulip0:  EEPROM default media type Autosense.
tulip0:  Index #0 - Media MII (#11) described by a 21140 MII PHY (1)
block.
00:0b.0:  MII transceiver #3 config 3100 status 7809 advertising 01e1.
00:0b.0:  Advertising 0001 on PHY 3, previously advertising 01e1.
00:0b.0:  Advertising 0001 (to advertise is 0001).
eth0: Digital DS21140 Tulip rev 32 at 0xb000, 00:00:C0:41:99:E9, IRQ 10.



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Re: Broken Tulip Driver

2001-03-12 Thread Ian Zink 

I will try tonight and let you know.

Thanks, Ian

Jeff Garzik wrote:

> Can you try out the updated Tulip driver in 2.4.2-ac19 and let me know
> if it works?
>
> ftp://ftp.us.kernel.org/pub/linux/kernel/people/alan/2.4/
>
> --
> Jeff Garzik   | May you have warm words on a cold evening,
> Building 1024 | a full mooon on a dark night,
> MandrakeSoft  | and a smooth road all the way to your door.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Broken Tulip Driver

2001-03-12 Thread Ian Zink 

Hello all, I have an SMC Etherpower10/100 in my system that refuses to
work under linux 2.4.2, it worked fine in 2.4.0 and the 2.2.x series. I
know the card is working fine since when I dual-boot into windows it
links fine. Strangely, once the linux drivers load it will not even link
to my hub at all. The light on the back of the card blinks green.
ifconfig shows lots of carrier errors. I will attach below all the
relevant information I can think of. Any help will be greatly
appreciated. Please CC me on any responses, as I'm not on the kernel
mailing list.

Thanks, Ian Zink


zforce:/home/zforce# gcc --version
2.95.3

(Note: I tried the 2.4.3-pre3 patch to see if the problem was already
fixed)

zforce:/home/zforce# uname -a
Linux zforce 2.4.3-pre3 #1 Sun Mar 11 20:13:44 CST 2001 i686 unknown

Interesting parts of /proc/pci
(This card works perfectly fine)

  Bus  0, device   9, function  0:
Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
(rev 0).
  IRQ 5.
  I/O at 0xd000 [0xd01f].
  Bus  0, device  10, function  0:
...

  Bus  0, device  11, function  0:
Ethernet controller: Digital Equipment Corporation DECchip 21140
[FasterNet] (rev 32).
  IRQ 10.
  Master Capable.  Latency=32.  Min Gnt=20.Max Lat=40.
  I/O at 0xb000 [0xb07f].
  Non-prefetchable 32 bit memory at 0xe080 [0xe080007f].


zforce:/home/zforce# ifconfig -a
(Take note of all of the carrier errors)
eth0  Link encap:Ethernet  HWaddr 00:00:C0:41:99:E9
  inet addr:10.1.1.1  Bcast:10.1.1.255  Mask:255.255.255.0
  UP BROADCAST MULTICAST  MTU:1500  Metric:1
  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  TX packets:0 errors:199 dropped:0 overruns:0 carrier:199
  collisions:0 txqueuelen:100
  RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
  Interrupt:10 Base address:0xb000

(IP address edited out for security)
eth1  Link encap:Ethernet  HWaddr 00:C0:F0:45:BD:04
  inet addr:xxx.xxx.xxx.xxx  Bcast:216.162.97.255
Mask:255.255.255.0
  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  RX packets:7736 errors:0 dropped:0 overruns:0 frame:0
  TX packets:8543 errors:0 dropped:0 overruns:0 carrier:0
  collisions:1 txqueuelen:100
  RX bytes:5565587 (5.3 Mb)  TX bytes:978504 (955.5 Kb)
  Interrupt:5 Base address:0xd000

zforce:/home/zforce# less /var/log/dmesg

Linux Tulip driver version 0.9.14 (February 20, 2001)
PCI: Found IRQ 10 for device 00:0b.0
eth0: Digital DS21140 Tulip rev 32 at 0xb000, 00:00:C0:41:99:E9, IRQ 10.

eth0:  EEPROM default media type Autosense.
eth0:  Index #0 - Media MII (#11) described by a 21140 MII PHY (1)
block.
eth0:  MII transceiver #3 config 3100 status 7809 advertising 01e1.
eth0:  Advertising 0001 on PHY 3, previously advertising 01e1.
eth0:  Advertising 0001 (to advertise is 0001).
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
  http://www.scyld.com/network/ne2k-pci.html
PCI: Found IRQ 5 for device 00:09.0
PCI: The same IRQ used for device 00:04.2
eth1: RealTek RTL-8029 found at 0xd000, IRQ 5, 00:C0:F0:45:BD:04.
...


Please remember to CC! Thanks again...


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Broken Tulip Driver

2001-03-12 Thread Ian Zink 

Hello all, I have an SMC Etherpower10/100 in my system that refuses to
work under linux 2.4.2, it worked fine in 2.4.0 and the 2.2.x series. I
know the card is working fine since when I dual-boot into windows it
links fine. Strangely, once the linux drivers load it will not even link
to my hub at all. The light on the back of the card blinks green.
ifconfig shows lots of carrier errors. I will attach below all the
relevant information I can think of. Any help will be greatly
appreciated. Please CC me on any responses, as I'm not on the kernel
mailing list.

Thanks, Ian Zink


zforce:/home/zforce# gcc --version
2.95.3

(Note: I tried the 2.4.3-pre3 patch to see if the problem was already
fixed)

zforce:/home/zforce# uname -a
Linux zforce 2.4.3-pre3 #1 Sun Mar 11 20:13:44 CST 2001 i686 unknown

Interesting parts of /proc/pci
(This card works perfectly fine)

  Bus  0, device   9, function  0:
Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
(rev 0).
  IRQ 5.
  I/O at 0xd000 [0xd01f].
  Bus  0, device  10, function  0:
...

  Bus  0, device  11, function  0:
Ethernet controller: Digital Equipment Corporation DECchip 21140
[FasterNet] (rev 32).
  IRQ 10.
  Master Capable.  Latency=32.  Min Gnt=20.Max Lat=40.
  I/O at 0xb000 [0xb07f].
  Non-prefetchable 32 bit memory at 0xe080 [0xe080007f].


zforce:/home/zforce# ifconfig -a
(Take note of all of the carrier errors)
eth0  Link encap:Ethernet  HWaddr 00:00:C0:41:99:E9
  inet addr:10.1.1.1  Bcast:10.1.1.255  Mask:255.255.255.0
  UP BROADCAST MULTICAST  MTU:1500  Metric:1
  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  TX packets:0 errors:199 dropped:0 overruns:0 carrier:199
  collisions:0 txqueuelen:100
  RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
  Interrupt:10 Base address:0xb000

(IP address edited out for security)
eth1  Link encap:Ethernet  HWaddr 00:C0:F0:45:BD:04
  inet addr:xxx.xxx.xxx.xxx  Bcast:216.162.97.255
Mask:255.255.255.0
  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  RX packets:7736 errors:0 dropped:0 overruns:0 frame:0
  TX packets:8543 errors:0 dropped:0 overruns:0 carrier:0
  collisions:1 txqueuelen:100
  RX bytes:5565587 (5.3 Mb)  TX bytes:978504 (955.5 Kb)
  Interrupt:5 Base address:0xd000

zforce:/home/zforce# less /var/log/dmesg

Linux Tulip driver version 0.9.14 (February 20, 2001)
PCI: Found IRQ 10 for device 00:0b.0
eth0: Digital DS21140 Tulip rev 32 at 0xb000, 00:00:C0:41:99:E9, IRQ 10.

eth0:  EEPROM default media type Autosense.
eth0:  Index #0 - Media MII (#11) described by a 21140 MII PHY (1)
block.
eth0:  MII transceiver #3 config 3100 status 7809 advertising 01e1.
eth0:  Advertising 0001 on PHY 3, previously advertising 01e1.
eth0:  Advertising 0001 (to advertise is 0001).
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
  http://www.scyld.com/network/ne2k-pci.html
PCI: Found IRQ 5 for device 00:09.0
PCI: The same IRQ used for device 00:04.2
eth1: RealTek RTL-8029 found at 0xd000, IRQ 5, 00:C0:F0:45:BD:04.
...


Please remember to CC! Thanks again...


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Re: Broken Tulip Driver

2001-03-12 Thread Ian Zink 

I will try tonight and let you know.

Thanks, Ian

Jeff Garzik wrote:

 Can you try out the updated Tulip driver in 2.4.2-ac19 and let me know
 if it works?

 ftp://ftp.us.kernel.org/pub/linux/kernel/people/alan/2.4/

 --
 Jeff Garzik   | May you have warm words on a cold evening,
 Building 1024 | a full mooon on a dark night,
 MandrakeSoft  | and a smooth road all the way to your door.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/