Re: [PATCH v7,1/3] dt-bindings: binding for jz4780-{nand,bch}
Hi Boris, On 04/11/15 07:57, Boris Brezillon wrote: Hi Harvey, On Tue, 6 Oct 2015 17:27:15 +0100 Harvey Hunt wrote: From: Alex Smith Add DT bindings for NAND devices connected to the NEMC on JZ4780 SoCs, as well as the hardware BCH controller, used by the jz4780_{nand,bch} drivers. Patch 3 does not seem to follow this binding: it still uses the ingenic,ecc-xxx properties and defines NAND timings. Thanks, I'll fix that for v8. Also, as answered to patch 3, I think it would be clearer to separate the nand controller and nand chip representation. That approach makes sense - I'll change it for the next series. Best Regards, Boris Best regards, Harvey Hunt -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Re: [PATCH v7,1/3] dt-bindings: binding for jz4780-{nand,bch}
Hi Boris, On 04/11/15 07:57, Boris Brezillon wrote: Hi Harvey, On Tue, 6 Oct 2015 17:27:15 +0100 Harvey Hunt wrote: From: Alex Smith Add DT bindings for NAND devices connected to the NEMC on JZ4780 SoCs, as well as the hardware BCH controller, used by the jz4780_{nand,bch} drivers. Patch 3 does not seem to follow this binding: it still uses the ingenic,ecc-xxx properties and defines NAND timings. I'll fix this for v8. Also, as answered to patch 3, I think it would be clearer to separate the nand controller and nand chip representation. I agree - I'll implement this in the next version. Best Regards, Boris Thanks, Harvey Hunt -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Re: [PATCH v7,1/3] dt-bindings: binding for jz4780-{nand,bch}
Hi Harvey, On Tue, 6 Oct 2015 17:27:15 +0100 Harvey Hunt wrote: > From: Alex Smith > > Add DT bindings for NAND devices connected to the NEMC on JZ4780 SoCs, > as well as the hardware BCH controller, used by the jz4780_{nand,bch} > drivers. Patch 3 does not seem to follow this binding: it still uses the ingenic,ecc-xxx properties and defines NAND timings. Also, as answered to patch 3, I think it would be clearer to separate the nand controller and nand chip representation. Best Regards, Boris > > Signed-off-by: Alex Smith > Cc: Zubair Lutfullah Kakakhel > Cc: David Woodhouse > Cc: Brian Norris > Cc: linux-...@lists.infradead.org > Cc: devicet...@vger.kernel.org > Cc: linux-kernel@vger.kernel.org > Cc: Alex Smith > Signed-off-by: Harvey Hunt > --- > v6 -> v7: > - Add nand-ecc-mode to DT bindings. > - Add nand-on-flash-bbt to DT bindings. > > v5 -> v6: > - No change. > > v4 -> v5: > - Rename ingenic,bch-device to ingenic,bch-controller to fit with >existing convention. > > v3 -> v4: > - No change > > v2 -> v3: > - Rebase to 4.0-rc6 > - Changed ingenic,ecc-size to common nand-ecc-step-size > - Changed ingenic,ecc-strength to common nand-ecc-strength > - Changed ingenic,busy-gpio to common rb-gpios > - Changed ingenic,wp-gpio to common wp-gpios > > v1 -> v2: > - Rebase to 4.0-rc3 > > .../bindings/mtd/ingenic,jz4780-nand.txt | 61 > ++ > 1 file changed, 61 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt > > diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt > b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt > new file mode 100644 > index 000..44a0468 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt > @@ -0,0 +1,61 @@ > +* Ingenic JZ4780 NAND/BCH > + > +This file documents the device tree bindings for NAND flash devices on the > +JZ4780. NAND devices are connected to the NEMC controller (described in > +memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must > +be children of the NEMC node. > + > +Required NAND device properties: > +- compatible: Should be set to "ingenic,jz4780-nand". > +- reg: For each bank with a NAND chip attached, should specify a bank number, > + an offset of 0 and a size of 0x100 (i.e. the whole NEMC bank). > + > +Optional NAND device properties: > +- ingenic,bch-controller: To make use of the hardware BCH controller, this > + property must contain a phandle for the BCH controller node. The required > + properties for this node are described below. If this is not specified, > + software BCH will be used instead. > +- nand-ecc-step-size: ECC block size in bytes. > +- nand-ecc-strength: ECC strength (max number of correctable bits). > +- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default > +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present > false > +- rb-gpios: GPIO specifier for the busy pin. > +- wp-gpios: GPIO specifier for the write protect pin. > + > +Example: > + > +nemc: nemc@1341 { > + ... > + > + nand: nand@1 { > + compatible = "ingenic,jz4780-nand"; > + reg = <1 0 0x100>; /* Bank 1 */ > + > + ingenic,bch-controller = <&bch>; > + nand-ecc-step-size = <1024>; > + nand-ecc-strength = <24>; > + nand-ecc-mode = "hw"; > + nand-on-flash-bbt; > + > + rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>; > + wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>; > + }; > +}; > + > +The BCH controller is a separate SoC component used for error correction on > +NAND devices. The following is a description of the device properties for a > +BCH controller. > + > +Required BCH properties: > +- compatible: Should be set to "ingenic,jz4780-bch". > +- reg: Should specify the BCH controller registers location and length. > +- clocks: Clock for the BCH controller. > + > +Example: > + > +bch: bch@134d { > + compatible = "ingenic,jz4780-bch"; > + reg = <0x134d 0x1>; > + > + clocks = <&cgu JZ4780_CLK_BCH>; > +}; -- Boris Brezillon, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
[PATCH v7,1/3] dt-bindings: binding for jz4780-{nand,bch}
From: Alex Smith Add DT bindings for NAND devices connected to the NEMC on JZ4780 SoCs, as well as the hardware BCH controller, used by the jz4780_{nand,bch} drivers. Signed-off-by: Alex Smith Cc: Zubair Lutfullah Kakakhel Cc: David Woodhouse Cc: Brian Norris Cc: linux-...@lists.infradead.org Cc: devicet...@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Alex Smith Signed-off-by: Harvey Hunt --- v6 -> v7: - Add nand-ecc-mode to DT bindings. - Add nand-on-flash-bbt to DT bindings. v5 -> v6: - No change. v4 -> v5: - Rename ingenic,bch-device to ingenic,bch-controller to fit with existing convention. v3 -> v4: - No change v2 -> v3: - Rebase to 4.0-rc6 - Changed ingenic,ecc-size to common nand-ecc-step-size - Changed ingenic,ecc-strength to common nand-ecc-strength - Changed ingenic,busy-gpio to common rb-gpios - Changed ingenic,wp-gpio to common wp-gpios v1 -> v2: - Rebase to 4.0-rc3 .../bindings/mtd/ingenic,jz4780-nand.txt | 61 ++ 1 file changed, 61 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt new file mode 100644 index 000..44a0468 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt @@ -0,0 +1,61 @@ +* Ingenic JZ4780 NAND/BCH + +This file documents the device tree bindings for NAND flash devices on the +JZ4780. NAND devices are connected to the NEMC controller (described in +memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must +be children of the NEMC node. + +Required NAND device properties: +- compatible: Should be set to "ingenic,jz4780-nand". +- reg: For each bank with a NAND chip attached, should specify a bank number, + an offset of 0 and a size of 0x100 (i.e. the whole NEMC bank). + +Optional NAND device properties: +- ingenic,bch-controller: To make use of the hardware BCH controller, this + property must contain a phandle for the BCH controller node. The required + properties for this node are described below. If this is not specified, + software BCH will be used instead. +- nand-ecc-step-size: ECC block size in bytes. +- nand-ecc-strength: ECC strength (max number of correctable bits). +- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false +- rb-gpios: GPIO specifier for the busy pin. +- wp-gpios: GPIO specifier for the write protect pin. + +Example: + +nemc: nemc@1341 { + ... + + nand: nand@1 { + compatible = "ingenic,jz4780-nand"; + reg = <1 0 0x100>; /* Bank 1 */ + + ingenic,bch-controller = <&bch>; + nand-ecc-step-size = <1024>; + nand-ecc-strength = <24>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + + rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>; + }; +}; + +The BCH controller is a separate SoC component used for error correction on +NAND devices. The following is a description of the device properties for a +BCH controller. + +Required BCH properties: +- compatible: Should be set to "ingenic,jz4780-bch". +- reg: Should specify the BCH controller registers location and length. +- clocks: Clock for the BCH controller. + +Example: + +bch: bch@134d { + compatible = "ingenic,jz4780-bch"; + reg = <0x134d 0x1>; + + clocks = <&cgu JZ4780_CLK_BCH>; +}; -- 2.6.0 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/