On Mon, Mar 09, 2015 at 11:58:18AM +, Zubair Lutfullah Kakakhel wrote:
> From: Alex Smith
>
> Add DT bindings for NAND devices connected to the NEMC on JZ4780 SoCs,
> as well as the hardware BCH controller, used by the jz4780_{nand,bch}
> drivers.
>
> Signed-off-by: Alex Smith
> Signed-off-by: Zubair Lutfullah Kakakhel
>
> ---
> V1 - > V2
> Rebase to 4.0-rc3
> ---
> .../bindings/mtd/ingenic,jz4780-nand.txt | 57
> ++
> 1 file changed, 57 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>
> diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> new file mode 100644
> index 000..6f2e128
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> @@ -0,0 +1,57 @@
> +* Ingenic JZ4780 NAND/BCH
> +
> +This file documents the device tree bindings for NAND flash devices on the
> +JZ4780. NAND devices are connected to the NEMC controller (described in
> +memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
> +be children of the NEMC node.
> +
> +Required NAND device properties:
> +- compatible: Should be set to "ingenic,jz4780-nand".
> +- reg: For each bank with a NAND chip attached, should specify a bank number,
> + an offset of 0 and a size of 0x100 (i.e. the whole NEMC bank).
> +
> +Optional NAND device properties:
> +- ingenic,bch-device: To make use of the hardware BCH controller, this
> property
> + must contain a phandle for the BCH controller node. The required properties
> + for this node are described below. If this is not specified, software BCH
> + will be used instead.
> +- ingenic,ecc-size: ECC block size in bytes.
> +- ingenic,ecc-strength: ECC strength (max number of correctable bits).
Can you use the generic nand-ecc-step-size and nand-ecc-strength
properties instead of defining new ones?
> +- ingenic,busy-gpio: GPIO specifier for the busy pin.
> +- ingenic,wp-gpio: GPIO specifier for the write protect pin.
The gipo.txt binding document recommends naming properties *-gpios, not
*-gpio. Also, these look like they are exposing the actualy R/B and WP#
pins as gpios, correct? If so, then I think it'd be good to give them
generic names, not 'ingenic,' names. That way, we might consider
supporting reusable code that handles them. And I see that sunxi-nand
already uses a generic name for the R/B pin: rb-gpios.
So these might work:
rb-gpios
wp-gpios
BTW, generic GPIO WP# handling was discussed a few months ago, though I
didn't see any patches yet:
http://lists.infradead.org/pipermail/linux-mtd/2015-January/057256.html
I see that your driver is just using this to disable write-protection
permanently, but I've seen cases where it helps to keep write-protection
enabled whenever you're not writing to the NAND.
> +
> +Example:
> +
> +nemc: nemc@1341 {
> + ...
> +
> + nand: nand@1 {
> + compatible = "ingenic,jz4780-nand";
> + reg = <1 0 0x100>; /* Bank 1 */
> +
> + ingenic,bch-device = <&bch>;
> + ingenic,ecc-size = <1024>;
> + ingenic,ecc-strength = <24>;
> +
> + ingenic,busy-gpio = <&gpa 20 GPIO_ACTIVE_LOW>;
> + ingenic,wp-gpio = <&gpf 22 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +The BCH controller is a separate SoC component used for error correction on
> +NAND devices. The following is a description of the device properties for a
> +BCH controller.
> +
> +Required BCH properties:
> +- compatible: Should be set to "ingenic,jz4780-bch".
> +- reg: Should specify the BCH controller registers location and length.
> +- clocks: Clock for the BCH controller.
> +
> +Example:
> +
> +bch: bch@134d {
> + compatible = "ingenic,jz4780-bch";
> + reg = <0x134d 0x1>;
> +
> + clocks = <&cgu JZ4780_CLK_BCH>;
> +};
Brian
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
