Re: [PATCH v2 2/7] [media] dt-bindings: tvp5150: Add input port connectors DT bindings
On 18-08-13 15:41, Rob Herring wrote: > On Mon, Aug 13, 2018 at 11:25:03AM +0200, Marco Felsch wrote: > > The TVP5150/1 decoders support different video input sources to their > > AIP1A/B pins. > > > > Possible configurations are as follows: > > - Analog Composite signal connected to AIP1A. > > - Analog Composite signal connected to AIP1B. > > - Analog S-Video Y (luminance) and C (chrominance) > > signals connected to AIP1A and AIP1B respectively. > > > > This patch extends the device tree bindings documentation to describe > > how the input connectors for these devices should be defined in a DT. > > > > Signed-off-by: Marco Felsch > > > > --- > > Changelog: > > v2: > > - adapt port layout in accordance with > > https://www.spinics.net/lists/linux-media/msg138546.html with the > > svideo-connector deviation (use only one endpoint) > > --- > > .../devicetree/bindings/media/i2c/tvp5150.txt | 191 +- > > 1 file changed, 185 insertions(+), 6 deletions(-) > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt > > b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt > > index 8c0fc1a26bf0..d647d671f14a 100644 > > --- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt > > +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt > > @@ -12,11 +12,31 @@ Optional Properties: > > - pdn-gpios: phandle for the GPIO connected to the PDN pin, if any. > > - reset-gpios: phandle for the GPIO connected to the RESETB pin, if any. > > > > -The device node must contain one 'port' child node for its digital output > > -video port, in accordance with the video interface bindings defined in > > -Documentation/devicetree/bindings/media/video-interfaces.txt. > > +The device node must contain one 'port' child node per device physical > > input > > +and output port, in accordance with the video interface bindings defined in > > +Documentation/devicetree/bindings/media/video-interfaces.txt. The port > > nodes > > +are numbered as follows > > > > -Required Endpoint Properties for parallel synchronization: > > + Name TypePort > > + -- > > + AIP1A sink0 > > + AIP1B sink1 > > + Y-OUT src 2 > > + > > +The device node must contain at least one sink port and the src port. Each > > input > > +port must be linked to an endpoint defined in > > +Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt. > > The > > +port/connector layout is as follows > > + > > +tvp-5150 port@0 (AIP1A) > > + endpoint@0 ---> Comp0-Con port > > + endpoint@1 ---> Svideo-Con port > > +tvp-5150 port@1 (AIP1B) > > + endpoint ---> Comp1-Con port > > +tvp-5150 port@2 > > + endpoint (video bitstream output at YOUT[0-7] parallel bus) > > + > > +Required Endpoint Properties for parallel synchronization on output port: > > > > - hsync-active: active state of the HSYNC signal. Must be <1> (HIGH). > > - vsync-active: active state of the VSYNC signal. Must be <1> (HIGH). > > @@ -26,7 +46,140 @@ Required Endpoint Properties for parallel > > synchronization: > > If none of hsync-active, vsync-active and field-even-active is specified, > > the endpoint is assumed to use embedded BT.656 synchronization. > > > > -Example: > > +Examples: > > Is it really necessary to enumerate every possibility? Just show the > most complicated case which is a superset of the rest. I just wanted to be a bit more verbose, since not all users (e.g. beginners) know how the of_graph works. Anyway, I can drop the 1st and 2nd example. > > > + > > +One Input: > > + > > +connector { > > + compatible = "composite-video-connector"; > > + label = "Composite0"; > > + > > + port { > > + composite0_to_tvp5150: endpoint { > > + remote-endpoint = <_to_composite0>; > > + }; > > + }; > > +}; > > + > > + { > > + ... > > + tvp5150@5c { > > + compatible = "ti,tvp5150"; > > + reg = <0x5c>; > > + pdn-gpios = < 30 GPIO_ACTIVE_LOW>; > > + reset-gpios = < 7 GPIO_ACTIVE_LOW>; > > + > > + port@0 { > > + reg = <0>; > > + > > + tvp5150_to_composite0: endpoint { > > + remote-endpoint = <_to_tvp5150>; > > + }; > > + }; > > + > > + port@2 { > > + reg = <2>; > > + > > + tvp5150_1: endpoint { > > + remote-endpoint = <_ep>; > > + }; > > + }; > > + }; > > +}; > > + > > +Two Inputs: > > + > > +comp_connector_1 { > > + compatible = "composite-video-connector"; > > + label = "Composite1"; > > + > > + port { > > + composite1_to_tvp5150: endpoint { > > + remote-endpoint = <_to_composite1>; > > + }; > > + }; > > +}; > > + >
Re: [PATCH v2 2/7] [media] dt-bindings: tvp5150: Add input port connectors DT bindings
On Mon, Aug 13, 2018 at 11:25:03AM +0200, Marco Felsch wrote: > The TVP5150/1 decoders support different video input sources to their > AIP1A/B pins. > > Possible configurations are as follows: > - Analog Composite signal connected to AIP1A. > - Analog Composite signal connected to AIP1B. > - Analog S-Video Y (luminance) and C (chrominance) > signals connected to AIP1A and AIP1B respectively. > > This patch extends the device tree bindings documentation to describe > how the input connectors for these devices should be defined in a DT. > > Signed-off-by: Marco Felsch > > --- > Changelog: > v2: > - adapt port layout in accordance with > https://www.spinics.net/lists/linux-media/msg138546.html with the > svideo-connector deviation (use only one endpoint) > --- > .../devicetree/bindings/media/i2c/tvp5150.txt | 191 +- > 1 file changed, 185 insertions(+), 6 deletions(-) > > diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt > b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt > index 8c0fc1a26bf0..d647d671f14a 100644 > --- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt > +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt > @@ -12,11 +12,31 @@ Optional Properties: > - pdn-gpios: phandle for the GPIO connected to the PDN pin, if any. > - reset-gpios: phandle for the GPIO connected to the RESETB pin, if any. > > -The device node must contain one 'port' child node for its digital output > -video port, in accordance with the video interface bindings defined in > -Documentation/devicetree/bindings/media/video-interfaces.txt. > +The device node must contain one 'port' child node per device physical input > +and output port, in accordance with the video interface bindings defined in > +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes > +are numbered as follows > > -Required Endpoint Properties for parallel synchronization: > + Name TypePort > + -- > + AIP1A sink0 > + AIP1B sink1 > + Y-OUT src 2 > + > +The device node must contain at least one sink port and the src port. Each > input > +port must be linked to an endpoint defined in > +Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt. > The > +port/connector layout is as follows > + > +tvp-5150 port@0 (AIP1A) > + endpoint@0 ---> Comp0-Con port > + endpoint@1 ---> Svideo-Con port > +tvp-5150 port@1 (AIP1B) > + endpoint ---> Comp1-Con port > +tvp-5150 port@2 > + endpoint (video bitstream output at YOUT[0-7] parallel bus) > + > +Required Endpoint Properties for parallel synchronization on output port: > > - hsync-active: active state of the HSYNC signal. Must be <1> (HIGH). > - vsync-active: active state of the VSYNC signal. Must be <1> (HIGH). > @@ -26,7 +46,140 @@ Required Endpoint Properties for parallel synchronization: > If none of hsync-active, vsync-active and field-even-active is specified, > the endpoint is assumed to use embedded BT.656 synchronization. > > -Example: > +Examples: Is it really necessary to enumerate every possibility? Just show the most complicated case which is a superset of the rest. > + > +One Input: > + > +connector { > + compatible = "composite-video-connector"; > + label = "Composite0"; > + > + port { > + composite0_to_tvp5150: endpoint { > + remote-endpoint = <_to_composite0>; > + }; > + }; > +}; > + > + { > + ... > + tvp5150@5c { > + compatible = "ti,tvp5150"; > + reg = <0x5c>; > + pdn-gpios = < 30 GPIO_ACTIVE_LOW>; > + reset-gpios = < 7 GPIO_ACTIVE_LOW>; > + > + port@0 { > + reg = <0>; > + > + tvp5150_to_composite0: endpoint { > + remote-endpoint = <_to_tvp5150>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + tvp5150_1: endpoint { > + remote-endpoint = <_ep>; > + }; > + }; > + }; > +}; > + > +Two Inputs: > + > +comp_connector_1 { > + compatible = "composite-video-connector"; > + label = "Composite1"; > + > + port { > + composite1_to_tvp5150: endpoint { > + remote-endpoint = <_to_composite1>; > + }; > + }; > +}; > + > +svid_connector { > + compatible = "svideo-connector"; > + label = "S-Video"; > + > + port { > + svideo_to_tvp5150: endpoint { > + remote-endpoint = <_to_svideo>; > + }; > + }; > +}; > + > + { > + ... > + tvp5150@5c { > + compatible = "ti,tvp5150"; > + reg = <0x5c>; > +
[PATCH v2 2/7] [media] dt-bindings: tvp5150: Add input port connectors DT bindings
The TVP5150/1 decoders support different video input sources to their AIP1A/B pins. Possible configurations are as follows: - Analog Composite signal connected to AIP1A. - Analog Composite signal connected to AIP1B. - Analog S-Video Y (luminance) and C (chrominance) signals connected to AIP1A and AIP1B respectively. This patch extends the device tree bindings documentation to describe how the input connectors for these devices should be defined in a DT. Signed-off-by: Marco Felsch --- Changelog: v2: - adapt port layout in accordance with https://www.spinics.net/lists/linux-media/msg138546.html with the svideo-connector deviation (use only one endpoint) --- .../devicetree/bindings/media/i2c/tvp5150.txt | 191 +- 1 file changed, 185 insertions(+), 6 deletions(-) diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt index 8c0fc1a26bf0..d647d671f14a 100644 --- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt @@ -12,11 +12,31 @@ Optional Properties: - pdn-gpios: phandle for the GPIO connected to the PDN pin, if any. - reset-gpios: phandle for the GPIO connected to the RESETB pin, if any. -The device node must contain one 'port' child node for its digital output -video port, in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. +The device node must contain one 'port' child node per device physical input +and output port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows -Required Endpoint Properties for parallel synchronization: + Name TypePort + -- + AIP1A sink0 + AIP1B sink1 + Y-OUT src 2 + +The device node must contain at least one sink port and the src port. Each input +port must be linked to an endpoint defined in +Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt. The +port/connector layout is as follows + +tvp-5150 port@0 (AIP1A) + endpoint@0 ---> Comp0-Con port + endpoint@1 ---> Svideo-Con port +tvp-5150 port@1 (AIP1B) + endpoint ---> Comp1-Con port +tvp-5150 port@2 + endpoint (video bitstream output at YOUT[0-7] parallel bus) + +Required Endpoint Properties for parallel synchronization on output port: - hsync-active: active state of the HSYNC signal. Must be <1> (HIGH). - vsync-active: active state of the VSYNC signal. Must be <1> (HIGH). @@ -26,7 +46,140 @@ Required Endpoint Properties for parallel synchronization: If none of hsync-active, vsync-active and field-even-active is specified, the endpoint is assumed to use embedded BT.656 synchronization. -Example: +Examples: + +One Input: + +connector { + compatible = "composite-video-connector"; + label = "Composite0"; + + port { + composite0_to_tvp5150: endpoint { + remote-endpoint = <_to_composite0>; + }; + }; +}; + + { + ... + tvp5150@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + pdn-gpios = < 30 GPIO_ACTIVE_LOW>; + reset-gpios = < 7 GPIO_ACTIVE_LOW>; + + port@0 { + reg = <0>; + + tvp5150_to_composite0: endpoint { + remote-endpoint = <_to_tvp5150>; + }; + }; + + port@2 { + reg = <2>; + + tvp5150_1: endpoint { + remote-endpoint = <_ep>; + }; + }; + }; +}; + +Two Inputs: + +comp_connector_1 { + compatible = "composite-video-connector"; + label = "Composite1"; + + port { + composite1_to_tvp5150: endpoint { + remote-endpoint = <_to_composite1>; + }; + }; +}; + +svid_connector { + compatible = "svideo-connector"; + label = "S-Video"; + + port { + svideo_to_tvp5150: endpoint { + remote-endpoint = <_to_svideo>; + }; + }; +}; + + { + ... + tvp5150@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + pdn-gpios = < 30 GPIO_ACTIVE_LOW>; + reset-gpios = < 7 GPIO_ACTIVE_LOW>; + +port@0 { +reg = <0>; + +tvp5150_to_svideo: endpoint@1 { +reg = <1>; +remote-endpoint = <_to_tvp5150>; +}; +}; + +