Re: [PATCH v2] OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
On Fri, May 11, 2012 at 2:04 PM, Russ Dill wrote: > On Thu, May 10, 2012 at 6:05 AM, Govindraj.R wrote: >> From: "Govindraj.R" >> >> The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of >> default uart pads) removed default uart pads that where getting populated >> and which was making rx pin wakeup capable. If uart pads was used in >> different mode by any other module then it would fail since the default >> pads took over all the uart pins forcefully. With removal of default pads >> the rx_pad wakeup for console uart while waking up from off mode is broken. [...] >> + * Check if uart is used in default tx/rx mode i.e. in mux >> mode0 >> + * if yes then configure rx pin for wake up capability >> + */ >> + if (!(rx_mode & 0x07) && !(tx_mode & 0x07)) >> + omap_serial_fill_uart_tx_rx_pads(bdata, uart); > > I realize the comment makes it clear, but it'd probably be better to > just make the code clear. I noticed mux.h has a OMAP_MODE_GPIO(x) > macro for testing if a mux is in mode4. Perhaps its time to start > expanding on that, at least with a macro like: > > #define OMAP_MUX_MODE(x) ((x) & OMAP_MUX_MODE7) > > So you can do a OMAP_MUX_MODE(rx_mode) == OMAP_MUX_MODE0 > Yes sure, will add the macro and use the same. (will post v3 addressing the comments received so far) -- Thanks, Govindraj.R -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH v2] OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
On Fri, May 11, 2012 at 12:41 AM, Tony Lindgren wrote: > * Govindraj.R [120510 06:09]: >> From: "Govindraj.R" >> >> The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of >> default uart pads) removed default uart pads that where getting populated >> and which was making rx pin wakeup capable. If uart pads was used in > > Nitpick.. this should say "were used" here ^^^ will change this. > >> --- a/arch/arm/mach-omap2/serial.c >> +++ b/arch/arm/mach-omap2/serial.c >> @@ -295,8 +353,7 @@ void __init omap_serial_board_init(struct >> omap_uart_port_info *info) >> bdata.pads = NULL; >> bdata.pads_cnt = 0; >> >> - if (cpu_is_omap44xx() || cpu_is_omap34xx()) >> - omap_serial_fill_default_pads(&bdata); >> + omap_serial_check_wakeup(&bdata, uart); > > Should this section become: > > if (!info) { > omap_serial_check_wakeup(&bdata, uart); > omap_serial_init_port(&bdata, NULL); > } else { > omap_serial_init_port(&bdata, &info[uart->num]); > } > > As if you have bdata, then there should not be anything to mux, > right? populating bdata should not depend on port_info, omap_serial_board_init takes only port info parameter and tries to populate wakeup parameter since it has not received the same from board file. And board file may or may not pass port info. So populating bdata -> for uart wakeup pin should not be coupled with availability of port info. -- Thanks, Govindraj.R -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH v2] OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
On Thu, May 10, 2012 at 6:05 AM, Govindraj.R wrote: > From: "Govindraj.R" > > The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of > default uart pads) removed default uart pads that where getting populated > and which was making rx pin wakeup capable. If uart pads was used in > different mode by any other module then it would fail since the default > pads took over all the uart pins forcefully. With removal of default pads > the rx_pad wakeup for console uart while waking up from off mode is broken. > > Utilise the mux api available to probe the availability of mux pins > in uart mode and probe for availability of uart pin in mux mode0 > if uart is available as uart pin itself then configure rx pin > as wakeup capable. > > This patch itself doesn't cater to all boards. Boards using uart rx wakeup > mechanism should ensure the usage of omap_serial_init_port by configuring > required uart ports and pass necessary mux data, till then this probing of > uart pins can cater to enabling of rx pad wakeup to most of the boards. > > This patch can also throw some boot warning from _omap_mux_get_by_name > if pin is requested for availability is not present while dynamically probing > the uart pins availability such boot warnings can be addressed only when board > files are patched with omap_serial_init_port calls passing the right pads > needed for a given port. > > Discussion Threads for reference: > http://www.spinics.net/lists/linux-omap/msg69859.html > http://www.spinics.net/lists/linux-omap/msg68659.html > > Cc: Felipe Balbi > Cc: Kevin Hilman > Cc: Russ Dill > Cc: Tony Lindgren > Cc: Paul Walmsley > Cc: Ameya Palande > Signed-off-by: Govindraj.R > --- > > Patching of all board files would be difficult as even I am not aware of all > omap-board schematics and uart port usage. So individual board file can be > enabled accordingly for uart usage by calling omap_serial_init_port call > with right mux data. > > for testing: Patch based on v3.4-rc6 > (tested on beagle-xm for off mode rx wakeup) > Patch targeted for v3.5 > > arch/arm/mach-omap2/mux.c | 3 +- > arch/arm/mach-omap2/mux.h | 10 ++ > arch/arm/mach-omap2/serial.c | 65 +++-- > 3 files changed, 72 insertions(+), 6 deletions(-) > > diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c > index 65c3391..d937ddd 100644 > --- a/arch/arm/mach-omap2/mux.c > +++ b/arch/arm/mach-omap2/mux.c > @@ -217,8 +217,7 @@ static int __init _omap_mux_get_by_name(struct > omap_mux_partition *partition, > return -ENODEV; > } > > -static int __init > -omap_mux_get_by_name(const char *muxname, > +int __init omap_mux_get_by_name(const char *muxname, > struct omap_mux_partition **found_partition, > struct omap_mux **found_mux) > { > diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h > index 69fe060..68927f1 100644 > --- a/arch/arm/mach-omap2/mux.h > +++ b/arch/arm/mach-omap2/mux.h > @@ -225,8 +225,18 @@ omap_hwmod_mux_init(struct omap_device_pad *bpads, int > nr_pads); > */ > void omap_hwmod_mux(struct omap_hwmod_mux_info *hmux, u8 state); > > +int omap_mux_get_by_name(const char *muxname, > + struct omap_mux_partition **found_partition, > + struct omap_mux **found_mux); > #else > > +static inline int omap_mux_get_by_name(const char *muxname, > + struct omap_mux_partition **found_partition, > + struct omap_mux **found_mux) > +{ > + return 0; > +} > + > static inline int omap_mux_init_gpio(int gpio, int val) > { > return 0; > diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c > index 9fc2f44..c097317 100644 > --- a/arch/arm/mach-omap2/serial.c > +++ b/arch/arm/mach-omap2/serial.c > @@ -57,6 +57,7 @@ struct omap_uart_state { > > struct list_head node; > struct omap_hwmod *oh; > + struct omap_device_pad default_omap_uart_pads[2]; > }; > > static LIST_HEAD(uart_list); > @@ -126,11 +127,68 @@ static void omap_uart_set_smartidle(struct > platform_device *pdev) {} > #endif /* CONFIG_PM */ > > #ifdef CONFIG_OMAP_MUX > -static void omap_serial_fill_default_pads(struct omap_board_data *bdata) > + > +#define OMAP_UART_DEFAULT_PAD_NAME_LEN 28 > +static char rx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN], > + tx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN] __initdata; > + > +static void __init > +omap_serial_fill_uart_tx_rx_pads(struct omap_board_data *bdata, > + struct omap_uart_state *uart) > +{ > + uart->default_omap_uart_pads[0].name = rx_pad_name; > + uart->default_omap_uart_pads[0].flags = OMAP_DEVICE_PAD_REMUX | > + > OMAP_DEVICE_PAD_WAKEUP; > + uart->default_omap_uart_pads[0].enable = OMAP_PIN_INPUT | > + OMAP_MUX_MODE0; > + uart->default
Re: [PATCH v2] OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
* Govindraj.R [120510 06:09]: > From: "Govindraj.R" > > The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of > default uart pads) removed default uart pads that where getting populated > and which was making rx pin wakeup capable. If uart pads was used in Nitpick.. this should say "were used" here ^^^ > --- a/arch/arm/mach-omap2/serial.c > +++ b/arch/arm/mach-omap2/serial.c > @@ -295,8 +353,7 @@ void __init omap_serial_board_init(struct > omap_uart_port_info *info) > bdata.pads = NULL; > bdata.pads_cnt = 0; > > - if (cpu_is_omap44xx() || cpu_is_omap34xx()) > - omap_serial_fill_default_pads(&bdata); > + omap_serial_check_wakeup(&bdata, uart); Should this section become: if (!info) { omap_serial_check_wakeup(&bdata, uart); omap_serial_init_port(&bdata, NULL); } else { omap_serial_init_port(&bdata, &info[uart->num]); } As if you have bdata, then there should not be anything to mux, right? Regards, Tony -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
[PATCH v2] OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
From: "Govindraj.R" The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of default uart pads) removed default uart pads that where getting populated and which was making rx pin wakeup capable. If uart pads was used in different mode by any other module then it would fail since the default pads took over all the uart pins forcefully. With removal of default pads the rx_pad wakeup for console uart while waking up from off mode is broken. Utilise the mux api available to probe the availability of mux pins in uart mode and probe for availability of uart pin in mux mode0 if uart is available as uart pin itself then configure rx pin as wakeup capable. This patch itself doesn't cater to all boards. Boards using uart rx wakeup mechanism should ensure the usage of omap_serial_init_port by configuring required uart ports and pass necessary mux data, till then this probing of uart pins can cater to enabling of rx pad wakeup to most of the boards. This patch can also throw some boot warning from _omap_mux_get_by_name if pin is requested for availability is not present while dynamically probing the uart pins availability such boot warnings can be addressed only when board files are patched with omap_serial_init_port calls passing the right pads needed for a given port. Discussion Threads for reference: http://www.spinics.net/lists/linux-omap/msg69859.html http://www.spinics.net/lists/linux-omap/msg68659.html Cc: Felipe Balbi Cc: Kevin Hilman Cc: Russ Dill Cc: Tony Lindgren Cc: Paul Walmsley Cc: Ameya Palande Signed-off-by: Govindraj.R --- Patching of all board files would be difficult as even I am not aware of all omap-board schematics and uart port usage. So individual board file can be enabled accordingly for uart usage by calling omap_serial_init_port call with right mux data. for testing: Patch based on v3.4-rc6 (tested on beagle-xm for off mode rx wakeup) Patch targeted for v3.5 arch/arm/mach-omap2/mux.c|3 +- arch/arm/mach-omap2/mux.h| 10 ++ arch/arm/mach-omap2/serial.c | 65 +++-- 3 files changed, 72 insertions(+), 6 deletions(-) diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 65c3391..d937ddd 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -217,8 +217,7 @@ static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition, return -ENODEV; } -static int __init -omap_mux_get_by_name(const char *muxname, +int __init omap_mux_get_by_name(const char *muxname, struct omap_mux_partition **found_partition, struct omap_mux **found_mux) { diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h index 69fe060..68927f1 100644 --- a/arch/arm/mach-omap2/mux.h +++ b/arch/arm/mach-omap2/mux.h @@ -225,8 +225,18 @@ omap_hwmod_mux_init(struct omap_device_pad *bpads, int nr_pads); */ void omap_hwmod_mux(struct omap_hwmod_mux_info *hmux, u8 state); +int omap_mux_get_by_name(const char *muxname, + struct omap_mux_partition **found_partition, + struct omap_mux **found_mux); #else +static inline int omap_mux_get_by_name(const char *muxname, + struct omap_mux_partition **found_partition, + struct omap_mux **found_mux) +{ + return 0; +} + static inline int omap_mux_init_gpio(int gpio, int val) { return 0; diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 9fc2f44..c097317 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -57,6 +57,7 @@ struct omap_uart_state { struct list_head node; struct omap_hwmod *oh; + struct omap_device_pad default_omap_uart_pads[2]; }; static LIST_HEAD(uart_list); @@ -126,11 +127,68 @@ static void omap_uart_set_smartidle(struct platform_device *pdev) {} #endif /* CONFIG_PM */ #ifdef CONFIG_OMAP_MUX -static void omap_serial_fill_default_pads(struct omap_board_data *bdata) + +#define OMAP_UART_DEFAULT_PAD_NAME_LEN 28 +static char rx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN], + tx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN] __initdata; + +static void __init +omap_serial_fill_uart_tx_rx_pads(struct omap_board_data *bdata, + struct omap_uart_state *uart) +{ + uart->default_omap_uart_pads[0].name = rx_pad_name; + uart->default_omap_uart_pads[0].flags = OMAP_DEVICE_PAD_REMUX | + OMAP_DEVICE_PAD_WAKEUP; + uart->default_omap_uart_pads[0].enable = OMAP_PIN_INPUT | + OMAP_MUX_MODE0; + uart->default_omap_uart_pads[0].idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0; + uart->default_omap_uart_pads[1].name = tx_pad_name; + uart->default_omap_uart_pads[1].enable = OMAP_PIN_OUTPUT | + OMAP_MUX_MODE0; + bdata->pa