On Mon, Jun 22, 2015 at 12:54:14AM +0800, Maciej S. Szmigiero wrote:
> This patch adds ability to define optional clock of connected
> USB hub to ChipIdea i.MX usb controller driver.
>
> This is needed for example for UDOO board.
> Previously, this board DT file used a fact that non-core registers
> of this USB controller have a separate driver (usbmisc_imx) which
> did allow defining a separate clock.
>
> Because the non-core registers are in fact using the same clock as
> main controller this allowed to use one of such clock definitions
> to enable USB hub clock instead.
>
> However, since commit 73dea4a912b2
> ("usb: chipidea: usbmisc_imx: delete clock information") this
> possibility no longer exists and loading USB support on this board
> results in a hard SoC lockup.
>
> Note that this is not specific to particular USB hub chip used,
> rather than to a particular board.
> Since this is a DT-based board there is no board platform file to
> put such clock enable.
> Also, USB bus devices aren't instantiated in DT file since it is an
> enumerable bus.
>
> NOP PHY also can't be used as clock consumer since this
> USB controller needs a true MXS phy definition, which accepts only
> one clock (different from USB controller one).
>
> Based on a patch previously submitted by Fabio Estevam, with consent.
>
> Signed-off-by: Maciej Szmigiero
>
> diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt
> b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt
> index 38a5480..fc65f1c 100644
> --- a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt
> +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt
> @@ -5,6 +5,8 @@ Required properties:
> - reg: Should contain registers location and length
> - interrupts: Should contain controller interrupt
> - fsl,usbphy: phandle of usb phy that connects to the port
> +- clocks: phandles of clocks that drive the controller and optionally
> + an USB hub connected to it
>
> Recommended properies:
> - phy_type: the type of the phy connected to the core. Should be one
> @@ -20,12 +22,14 @@ Optional properties:
> - external-vbus-divider: enables off-chip resistor divider for Vbus
> - maximum-speed: limit the maximum connection speed to "full-speed".
> - tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts
> +- clock-names: must be "default", "hub" if optional USB hub clock is used
>
> Examples:
> usb@02184000 { /* USB OTG */
> compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
> reg = <0x02184000 0x200>;
> interrupts = <0 43 0x04>;
> + clocks = <&clks IMX6QDL_CLK_USBOH3>;
> fsl,usbphy = <&usbphy1>;
> fsl,usbmisc = <&usbmisc 0>;
> disable-over-current;
> diff --git a/drivers/usb/chipidea/ci_hdrc_imx.c
> b/drivers/usb/chipidea/ci_hdrc_imx.c
> index 389f0e0..bb7f859 100644
> --- a/drivers/usb/chipidea/ci_hdrc_imx.c
> +++ b/drivers/usb/chipidea/ci_hdrc_imx.c
> @@ -65,6 +65,7 @@ struct ci_hdrc_imx_data {
> struct usb_phy *phy;
> struct platform_device *ci_pdev;
> struct clk *clk;
> + struct clk *clk_hub;
> struct imx_usbmisc_data *usbmisc_data;
> bool supports_runtime_pm;
> bool in_lpm;
> @@ -196,6 +197,16 @@ static int ci_hdrc_imx_probe(struct platform_device
> *pdev)
> goto disable_device;
> }
>
> + data->clk_hub = devm_clk_get(&pdev->dev, "hub");
> + if (!IS_ERR(data->clk_hub)) {
> + ret = clk_prepare_enable(data->clk_hub);
> + if (ret) {
> + dev_err(&pdev->dev,
> + "Failed to enable clk_hub: %d\n", ret);
> + goto disable_device;
> + }
> + }
> +
Hi Maciej,
As I said before, the USB HUB is just an USB peripheral, we should
not put a peripheral's clock information to controller driver, I think
hub driver should take responsibilities for it, just like other usb
pheripheral drivers, like usb modem, etc. You can talk it with Alan
Stern about it.
> platform_set_drvdata(pdev, data);
>
> if (data->supports_runtime_pm) {
> @@ -223,6 +234,8 @@ static int ci_hdrc_imx_remove(struct platform_device
> *pdev)
> pm_runtime_disable(&pdev->dev);
> pm_runtime_put_noidle(&pdev->dev);
> }
> + if (!IS_ERR(data->clk_hub))
> + clk_disable_unprepare(data->clk_hub);
> ci_hdrc_remove_device(data->ci_pdev);
> clk_disable_unprepare(data->clk);
>
>
--
Best Regards,
Peter Chen
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in