[PATCH 1/2] cfg80211: Add support to set tx power for a station associated
This patch adds support to set transmit power setting type and transmit
power level attributes to NL80211_CMD_SET_STATION in order to facilitate
adjusting the transmit power level of a station associated to the AP.
The added attributes allow selection of automatic and limited transmit
power level, with the level defined in mBm format.
Signed-off-by: Ashok Raj Nagarajan
---
include/net/cfg80211.h | 5
include/uapi/linux/nl80211.h | 12 ++
net/wireless/nl80211.c | 54
3 files changed, 71 insertions(+)
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 6392167..4bf761d 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -797,6 +797,10 @@ enum station_parameters_apply_mask {
* @opmode_notif: operating mode field from Operating Mode Notification
* @opmode_notif_used: information if operating mode field is used
* @support_p2p_ps: information if station supports P2P PS mechanism
+ * @txpwr: tx power (in mBm) to be used for sending data traffic. If tx power
+ * is not provided, the default per-interface tx power setting will be
+ * overriding. Driver should be picking up the lowest tx power, either tx
+ * power per-interface or per-station.
*/
struct station_parameters {
const u8 *supported_rates;
@@ -823,6 +827,7 @@ struct station_parameters {
u8 opmode_notif;
bool opmode_notif_used;
int support_p2p_ps;
+ unsigned int txpwr;
};
/**
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index e23d786..fe28006 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -1819,6 +1819,15 @@ enum nl80211_commands {
*
* @NL80211_ATTR_PAD: attribute used for padding for 64-bit alignment
*
+ * @NL80211_ATTR_STA_TX_POWER_SETTING: Transmit power setting type (u32) for
+ * station associated with the AP. See &enum nl80211_tx_power_setting for
+ * possible values.
+ * @NL80211_ATTR_STA_TX_POWER: Transmit power level (u32) in mBm units. This
+ * allows to set Tx power for a station. If this attribute is not included,
+ * the default per-interface tx power setting will be overriding. Driver
+ * should be picking up the lowest tx power, either tx power per-interface
+ * or per-station.
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
@@ -2201,6 +2210,9 @@ enum nl80211_attrs {
NL80211_ATTR_PAD,
+ NL80211_ATTR_STA_TX_POWER_SETTING,
+ NL80211_ATTR_STA_TX_POWER,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index d759901..0ef7377 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -257,6 +257,8 @@ static const struct nla_policy
nl80211_policy[NUM_NL80211_ATTR] = {
[NL80211_ATTR_STA_SUPPORTED_RATES] = { .type = NLA_BINARY,
.len = NL80211_MAX_SUPP_RATES },
[NL80211_ATTR_STA_PLINK_ACTION] = { .type = NLA_U8 },
+ [NL80211_ATTR_STA_TX_POWER_SETTING] = { .type = NLA_U32 },
+ [NL80211_ATTR_STA_TX_POWER] = { .type = NLA_U32 },
[NL80211_ATTR_STA_VLAN] = { .type = NLA_U32 },
[NL80211_ATTR_MNTR_FLAGS] = { /* NLA_NESTED can't be empty */ },
[NL80211_ATTR_MESH_ID] = { .type = NLA_BINARY,
@@ -4380,6 +4382,32 @@ static int nl80211_set_station(struct sk_buff *skb,
struct genl_info *info)
params.local_pm = pm;
}
+ if (info->attrs[NL80211_ATTR_STA_TX_POWER_SETTING]) {
+ enum nl80211_tx_power_setting type;
+ int idx;
+
+ if (!rdev->ops->set_tx_power)
+ return -EOPNOTSUPP;
+
+ idx = NL80211_ATTR_STA_TX_POWER_SETTING;
+ type = nla_get_u32(info->attrs[idx]);
+
+ if (!info->attrs[NL80211_ATTR_STA_TX_POWER] &&
+ (type != NL80211_TX_POWER_AUTOMATIC))
+ return -EINVAL;
+
+ if (type != NL80211_TX_POWER_AUTOMATIC) {
+ if (type == NL80211_TX_POWER_LIMITED) {
+ idx = NL80211_ATTR_STA_TX_POWER;
+ params.txpwr = nla_get_u32(info->attrs[idx]);
+ } else {
+ return -EINVAL;
+ }
+ } else {
+ params.txpwr = 0;
+ }
+ }
+
/* Include parameters for TDLS peer (will check later) */
err = nl80211_set_station_tdls(info, ¶ms);
if (err)
@@ -4507,6 +4535,32 @@ static int nl80211_new_station(struct sk_buff *skb,
struct genl_info *info)
return -EINVAL;
}
+ if (info->attrs[NL80211_ATTR_STA_TX_POWER_SETTI
Re: [PATCH 1/2] cfg80211: Add support to set tx power for a station associated
On Tue, 2016-06-14 at 23:14 +0530, Ashok Raj Nagarajan wrote: > This patch adds support to set transmit power setting type and > transmit power level attributes to NL80211_CMD_SET_STATION in order > to facilitate adjusting the transmit power level of a station > associated to the AP. Why would you ever need to do that manually? Please give more explanation in the commit message. We have minstrel-blues (which never made it into the code, but that's just because the submitter went away) doing power adjustments, so you need to explain why this should be necessary. johannes -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 1/2] cfg80211: Add support to set tx power for a station associated
On 2016-06-28 16:18, Johannes Berg wrote: On Tue, 2016-06-14 at 23:14 +0530, Ashok Raj Nagarajan wrote: This patch adds support to set transmit power setting type and transmit power level attributes to NL80211_CMD_SET_STATION in order to facilitate adjusting the transmit power level of a station associated to the AP. Why would you ever need to do that manually? Please give more explanation in the commit message. We have minstrel-blues (which never made it into the code, but that's just because the submitter went away) doing power adjustments, so you need to explain why this should be necessary. Hi Johannes, Sure.. First use case will be to help with the problem of legacy client devices that roam across multiple APs. It is a classic enterprise Wi-Fi AP problem, often managed by a "network controller" unit that is connected to all the APs. The problem is how to handle seamless handoff of clients between multiple APs while maximizing the client throughput and minimizing disruption of IP application services like VoIP calls and video streaming. A legacy client will often hold onto an AP association, even down to 1 Mbps as it roams away. Instead, if the AP can recognise that the client RSSI (and therefore throughput) is poor, it can "drop" the Tx power significantly (just to that client) such that it forces the client to look for a better, closer, and therefore higher-throughput association. It would "give it a kick" without blacklisting it. It just needs to hold the power low for the small amount of time it takes to convince it to go away. Other use cases may be - Support a form of QoS per STA since a higher MCS rate might be achievable, and CW delays might be reduced - The optimal power can be negotiated (closed loop) or observed (open loop) for a given STA, reducing needless congestion on the overall channel - Reduce power to a STA that does not support certain radio features (e.g. 11b clients) Thanks, Ashok johannes -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 1/2] cfg80211: Add support to set tx power for a station associated
> Sure.. First use case will be to help with the problem of legacy > client devices that roam across multiple APs. It is a classic > enterprise Wi-Fi AP problem, often managed by a "network controller" > unit that is connected to all the APs. > The problem is how to handle seamless handoff of clients between > multiple APs while maximizing the client throughput and minimizing > disruption of IP application services like VoIP calls and video > streaming. A legacy client will often hold onto an AP association, > even down to 1 Mbps as it roams away. Instead, if the AP can > recognise that the client RSSI (and therefore throughput) is poor, it > can "drop" the Tx power significantly (just to that client) such that > it forcesthe client to look for a better, closer, and therefore > higher-throughputassociation. It would "give it a kick" without > blacklisting it. It just needsto hold the power low for the small > amount of time it takes to convince it to go away. Not sure that *works* since implementations may just compare beacon signal strength and hold on to the AP based on that, but it does seem like a reasonable use case. How would this interact with automatic adjustment though? johannes -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 1/2] cfg80211: Add support to set tx power for a station associated
On 08/01/2016 02:29 AM, Johannes Berg wrote: Sure.. First use case will be to help with the problem of legacy client devices that roam across multiple APs. It is a classic enterprise Wi-Fi AP problem, often managed by a "network controller" unit that is connected to all the APs. The problem is how to handle seamless handoff of clients between multiple APs while maximizing the client throughput and minimizing disruption of IP application services like VoIP calls and video streaming. A legacy client will often hold onto an AP association, even down to 1 Mbps as it roams away. Instead, if the AP can recognise that the client RSSI (and therefore throughput) is poor, it can "drop" the Tx power significantly (just to that client) such that it forcesthe client to look for a better, closer, and therefore higher-throughputassociation. It would "give it a kick" without blacklisting it. It just needsto hold the power low for the small amount of time it takes to convince it to go away. Not sure that *works* since implementations may just compare beacon signal strength and hold on to the AP based on that, but it does seem like a reasonable use case. How is that better than just kicking the station deliberately and/or refusing to send frames to it at all? Thanks, Ben How would this interact with automatic adjustment though? johannes -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html -- Ben Greear Candela Technologies Inc http://www.candelatech.com -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 1/2] cfg80211: Add support to set tx power for a station associated
On 2016-08-01 18:57, Ben Greear wrote: On 08/01/2016 02:29 AM, Johannes Berg wrote: Sure.. First use case will be to help with the problem of legacy client devices that roam across multiple APs. It is a classic enterprise Wi-Fi AP problem, often managed by a "network controller" unit that is connected to all the APs. The problem is how to handle seamless handoff of clients between multiple APs while maximizing the client throughput and minimizing disruption of IP application services like VoIP calls and video streaming. A legacy client will often hold onto an AP association, even down to 1 Mbps as it roams away. Instead, if the AP can recognise that the client RSSI (and therefore throughput) is poor, it can "drop" the Tx power significantly (just to that client) such that it forcesthe client to look for a better, closer, and therefore higher-throughputassociation. It would "give it a kick" without blacklisting it. It just needsto hold the power low for the small amount of time it takes to convince it to go away. Not sure that *works* since implementations may just compare beacon signal strength and hold on to the AP based on that, but it does seem like a reasonable use case. How is that better than just kicking the station deliberately and/or refusing to send frames to it at all? Ben, deliberately kicking out the station can potentially cause the black listing behaviour on the client side and results in connection failures. Each client handles the kickout logic differently. Reducing the tx power, causes the station to trigger its roaming algorithm. How would this interact with automatic adjustment though? Johannes, In the case of manual intervention by user, the firmware will check three values - regulatory domain, automatic tx power and user entered value. System will always cap to the minimum of these values and see to that we do not exceed the regulatory power limits. If there are no more comments I will resent this patch series after rebase. Thanks, Ashok johannes -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 1/2] cfg80211: Add support to set tx power for a station associated
On 11/07/2016 06:10 AM, Ashok Raj Nagarajan wrote: On 2016-08-01 18:57, Ben Greear wrote: On 08/01/2016 02:29 AM, Johannes Berg wrote: Sure.. First use case will be to help with the problem of legacy client devices that roam across multiple APs. It is a classic enterprise Wi-Fi AP problem, often managed by a "network controller" unit that is connected to all the APs. The problem is how to handle seamless handoff of clients between multiple APs while maximizing the client throughput and minimizing disruption of IP application services like VoIP calls and video streaming. A legacy client will often hold onto an AP association, even down to 1 Mbps as it roams away. Instead, if the AP can recognise that the client RSSI (and therefore throughput) is poor, it can "drop" the Tx power significantly (just to that client) such that it forcesthe client to look for a better, closer, and therefore higher-throughputassociation. It would "give it a kick" without blacklisting it. It just needsto hold the power low for the small amount of time it takes to convince it to go away. Not sure that *works* since implementations may just compare beacon signal strength and hold on to the AP based on that, but it does seem like a reasonable use case. How is that better than just kicking the station deliberately and/or refusing to send frames to it at all? Ben, deliberately kicking out the station can potentially cause the black listing behaviour on the client side and results in connection failures. Each client handles the kickout logic differently. Reducing the tx power, causes the station to trigger its roaming algorithm. We tested some phones a year or so ago, and used a variable attenuator to decrease the signal of one AP while ramping up signal of a second AP. They did not roam until they lost connection, and since we were not using an isolation chamber, we could not get the AP signal less than around -75 DB, so in our test, the phones often did not roam at all. http://www.candelatech.com/cookbook.php?vol=wifire&book=Emulating+Station+Motion+with+Programmable+Attenuator So, I am not sure you can assume much about scanning behaviour either. Maybe newer phones are better... Thanks, Ben -- Ben Greear Candela Technologies Inc http://www.candelatech.com
Re: [PATCH 1/2] cfg80211: Add support to set tx power for a station associated
> In the case of manual intervention by user, the firmware will check > three > values - regulatory domain, automatic tx power and user entered > value. > System > will always cap to the minimum of these values and see to that we do > not > exceed > the regulatory power limits. Fair enough. > If there are no more comments I will resent this patch series after > rebase. I suspect we should also have some kind of capability for all of this, so it can be used reliably? johannes
