Re: Intel D945GCNL with OpenBSD 4.4 Hangs
Marcello if you like that Series of Intel motherboards, i can assure you that D945GCPE works just fine: OpenBSD 4.2-stable (GENERIC) #0: Fri Mar 28 15:20:03 ART 2008 root@:/u/system/src/sys/arch/i386/compile/GENERIC RTC BIOS diagnostic error 80clock_battery cpu0: Intel(R) Pentium(R) 4 CPU 3.00GHz (GenuineIntel 686-class) 3 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,TM2,CNXT-ID,CX16,xTPR real mem = 1062670336 (1013MB) avail mem = 1019904000 (972MB) RTC BIOS diagnostic error 80clock_battery mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 07/10/07, SMBIOS rev. 2.5 @ 0xe4440 (35 entries) bios0: vendor Intel Corp. version PE94510M.86A.0050.2007.0710.1559 date 07/10/2007 bios0: Intel Corporation D945GCPE apm0 at bios0: Power Management spec V1.2 apm0: AC on, battery charge unknown, estimated 0:00 hours apm0: flags 30102 dobusy 0 doidle 1 pcibios at bios0 function 0x1a not configured bios0: ROM list: 0xc/0xae00! cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 Intel 82945GP rev 0x02: rng active, 800Kb/sec vga1 at pci0 dev 2 function 0 Intel 82945G Video rev 0x02: aperture at 0x4000, size 0x1000 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) ppb0 at pci0 dev 28 function 0 Intel 82801GB PCIE rev 0x01 pci1 at ppb0 bus 1 re0 at pci1 dev 0 function 0 Realtek 8101E rev 0x01: RTL8101E (0x3400), irq 11, address 00:1c:c0:0b:99:2e rlphy0 at re0 phy 7: RTL8201L 10/100 PHY, rev. 1 ppb1 at pci0 dev 30 function 0 Intel 82801BA AGP rev 0xe1 pci2 at ppb1 bus 2 ichpcib0 at pci0 dev 31 function 0 Intel 82801GB LPC rev 0x01: PM disabled pciide0 at pci0 dev 31 function 1 Intel 82801GB IDE rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility pciide0: channel 0 disabled (no drives) pciide0: channel 1 ignored (disabled) pciide1 at pci0 dev 31 function 2 Intel 82801GB SATA rev 0x01: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI pciide1: using irq 10 for native-PCI interrupt wd0 at pciide1 channel 0 drive 0: WDC WD1600AABS-00PRA0 wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors wd1 at pciide1 channel 0 drive 1: WDC WD1600AABS-00PRA0 wd1: 16-sector PIO, LBA48, 152627MB, 312581808 sectors wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5 wd1(pciide1:0:1): using PIO mode 4, Ultra-DMA mode 5 ichiic0 at pci0 dev 31 function 3 Intel 82801GB SMBus rev 0x01: irq 10 iic0 at ichiic0 isa0 at ichpcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: PC speaker spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 biomask f7fd netmask fffd ttymask pctr: user-level cycle counter enabled mtrr: Pentium Pro MTRR support dkcsum: wd0 matches BIOS drive 0x80 dkcsum: wd1 matches BIOS drive 0x81 root on wd0a swap on wd0b dump on wd0b Marcello Cruz escribis: 1) I updated the BIOS to NL94510J.86A.0033.2008.0807.1932. This is the most recent BIOS available from Intel to this board. The old BIOS was NL94510J.86A.0017.2007.0828.1137. Accordingly to the flash utility, I cannot use a BIOS update with different prefix (NL94510J.86A). 2) Following another post I disabled APM. With version 4.3 (OpenBSD), it worked, but the system become unstable and I lose connectivity with remote SSH sessions. With version 4.4 (OpenBSD) the system hangs at mtrr: Pentium Pro MTRR Support. 3) Then I tried to disable ACPI. With version 4.3 the system hangs at npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16. With version 4.4 (OpenBSD) the system hangs when I activate the second NIC (up, dhcp or IP address). 4) Then I installed version 4.4 on a different hardware with the 3 NIC (3Com 3c905B 100Base-TX, DLink DFE-520TX, plus the on-board NIC with Realket chipset). The system works with no problem. So, I realize the problem is with the motherboard. But where? 5) A page (http://www.intel.com/support/motherboards/desktop/sb/CS-008326.htm) from Intel say that there is support for Linux. What does RTC BIOS diagnostic error 80clock_battery mean? Any clues? The best option is to ask the dealer to replace the board for another wich supports Linux. Is that right? Or, is there another solution? Rgds Marcello OpenBSD 4.4 (GENERIC) #1021: Tue Aug 12 17:16:55 MDT 2008 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC RTC BIOS diagnostic error 80clock_battery cpu0: Intel(R) Celeron(R) CPU 430 @ 1.80GHz (GenuineIntel 686-class) 1.80 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR real mem = 1062412288
Re: Intel D945GCNL with OpenBSD 4.4 Hangs
1) I updated the BIOS to NL94510J.86A.0033.2008.0807.1932. This is the most recent BIOS available from Intel to this board. The old BIOS was NL94510J.86A.0017.2007.0828.1137. Accordingly to the flash utility, I cannot use a BIOS update with different prefix (NL94510J.86A). 2) Following another post I disabled APM. With version 4.3 (OpenBSD), it worked, but the system become unstable and I lose connectivity with remote SSH sessions. With version 4.4 (OpenBSD) the system hangs at mtrr: Pentium Pro MTRR Support. 3) Then I tried to disable ACPI. With version 4.3 the system hangs at npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16. With version 4.4 (OpenBSD) the system hangs when I activate the second NIC (up, dhcp or IP address). 4) Then I installed version 4.4 on a different hardware with the 3 NIC (3Com 3c905B 100Base-TX, DLink DFE-520TX, plus the on-board NIC with Realket chipset). The system works with no problem. So, I realize the problem is with the motherboard. But where? 5) A page (http://www.intel.com/support/motherboards/desktop/sb/CS-008326.htm) from Intel say that there is support for Linux. What does RTC BIOS diagnostic error 80clock_battery mean? Any clues? The best option is to ask the dealer to replace the board for another wich supports Linux. Is that right? Or, is there another solution? Rgds Marcello OpenBSD 4.4 (GENERIC) #1021: Tue Aug 12 17:16:55 MDT 2008 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC RTC BIOS diagnostic error 80clock_battery cpu0: Intel(R) Celeron(R) CPU 430 @ 1.80GHz (GenuineIntel 686-class) 1.80 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR real mem = 1062412288 (1013MB) avail mem = 1018851328 (971MB) RTC BIOS diagnostic error 80clock_battery mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 08/07/08, SMBIOS rev. 2.4 @ 0xe44d0 (28 entries) bios0: vendor Intel Corp. version NL94510J.86A.0033.2008.0807.1932 date 08/07/2008 bios0: Intel Corporation D945GCNL apm0 at bios0: Power Management spec V1.2 apm0: AC on, battery charge unknown, estimated 0:00 hours acpi at bios0 function 0x0 not configured pcibios at bios0 function 0x1a not configured bios0: ROM list: 0xc/0xae00! cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 Intel 82945G Host rev 0x02 vga1 at pci0 dev 2 function 0 Intel 82945G Video rev 0x02 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) agp0 at vga1: aperture at 0x4000, size 0x1000 drm at vga1 unsupported azalia0 at pci0 dev 27 function 0 Intel 82801GB HD Audio rev 0x01: irq 9 azalia0: codec[s]: Realtek/0x0888 audio0 at azalia0 ppb0 at pci0 dev 28 function 0 Intel 82801GB PCIE rev 0x01 pci1 at ppb0 bus 1 ppb1 at pci0 dev 28 function 1 Intel 82801GB PCIE rev 0x01 pci2 at ppb1 bus 2 re0 at pci2 dev 0 function 0 Realtek 8168 rev 0x01: RTL8168 2 (0x3800), irq 10, address 00:1c:c0:7b:06:d9 rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2 ppb2 at pci0 dev 28 function 2 Intel 82801GB PCIE rev 0x01 pci3 at ppb2 bus 3 ppb3 at pci0 dev 28 function 3 Intel 82801GB PCIE rev 0x01 pci4 at ppb3 bus 4 uhci0 at pci0 dev 29 function 0 Intel 82801GB USB rev 0x01: irq 11 uhci1 at pci0 dev 29 function 1 Intel 82801GB USB rev 0x01: irq 9 uhci2 at pci0 dev 29 function 2 Intel 82801GB USB rev 0x01: irq 10 uhci3 at pci0 dev 29 function 3 Intel 82801GB USB rev 0x01: irq 11 ehci0 at pci0 dev 29 function 7 Intel 82801GB USB rev 0x01: irq 11 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 Intel EHCI root hub rev 2.00/1.00 addr 1 ppb4 at pci0 dev 30 function 0 Intel 82801BA Hub-to-PCI rev 0xe1 pci5 at ppb4 bus 5 xl0 at pci5 dev 4 function 0 3Com 3c905B 100Base-TX rev 0x24: irq 11, address 00:10:4b:6c:69:53 exphy0 at xl0 phy 24: 3Com internal media interface vr0 at pci5 dev 5 function 0 VIA VT6105 RhineIII rev 0x8b: irq 11, address 00:21:91:52:ac:df ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 9: OUI 0x004063, model 0x0034 ichpcib0 at pci0 dev 31 function 0 Intel 82801GB LPC rev 0x01: PM disabled pciide0 at pci0 dev 31 function 1 Intel 82801GB IDE rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility pciide0: channel 0 disabled (no drives) pciide0: channel 1 ignored (disabled) pciide1 at pci0 dev 31 function 2 Intel 82801GB SATA rev 0x01: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI pciide1: using irq 9 for native-PCI interrupt wd0 at pciide1 channel 0 drive 0: SAMSUNG HD161HJ wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5 atapiscsi0 at pciide1 channel 1 drive 0 scsibus0 at atapiscsi0: 2 targets, initiator 7 cd0 at scsibus0 targ 0 lun 0: HL-DT-ST, DVDRAM GH20NS15, IL00 ATAPI 5/cdrom removable cd0(pciide1:1:0): using PIO
Re: Intel D945GCNL with OpenBSD 4.4 Hangs
On OBSD 4.4 when I disable apm it hangs on mtrr: Pentium Pro MTRR support. On OBSD 4.3, it give me the login prompt, but when I activate the second NIC (up, dhcp, IP address) the the system hangs. A documentation from Intel (http://www.intel.com/support/motherboards/desktop/sb/CS-028426.htm) says that a message error could appear when installing W2K: The BIOS in this System is not Fully ACPI Compliant. So, i tried to disable acpi, but the system hangs at npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 with OBSD 4.3. With OBSD 4.4 the system hangs only when I activate the second NIC (up, dhcp, IP address). Another test I did was to disable the on-board NIC and put a second off-board NIC, so the system had 3 NICs. The system hangs only when I activate the second NIC. In this case, the DLink NIC (DFE-520TX) make the system show the message Watchdog Timeout. The same NICs in another motherboard doesn't cause the system to hang or to show error messages. Also, Intel says that this board has no support for Linux. Should I discard this model or has something else I can do? Ooops, I forgot to mention that I have 3 of these boards and the same occurs with all of them. Rgds, Marcello - Original Message - From: Stijn mail.st...@telenet.be To: Marcello Cruz marcello.c...@globo.com Sent: Thursday, April 09, 2009 5:03 PM Subject: Re: Intel D945GCNL with OpenBSD 4.4 Hangs OpenBSD 4.4 (GENERIC) #1021: Tue Aug 12 17:16:55 MDT 2008 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC RTC BIOS diagnostic error 80clock_battery mtrr: Pentium Pro MTRR support Hi, Can you disable apm at the boot prompt? This way acpi will be used. Also try a recent snapshot to see if this helps. HTH, Stijn
Re: Intel D945GCNL with OpenBSD 4.4 Hangs
did you try the recent snapshot Stijn suggested yet? if it still fails, the information about 4.3, 4.4, apm etc are useful extra data points, but a -current snapshot should be the first thing to try. On 2009-04-10, Marcello Cruz marcello.c...@globo.com wrote: On OBSD 4.4 when I disable apm it hangs on mtrr: Pentium Pro MTRR support. On OBSD 4.3, it give me the login prompt, but when I activate the second NIC (up, dhcp, IP address) the the system hangs. A documentation from Intel (http://www.intel.com/support/motherboards/desktop/sb/CS-028426.htm) says that a message error could appear when installing W2K: The BIOS in this System is not Fully ACPI Compliant. So, i tried to disable acpi, but the system hangs at npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 with OBSD 4.3. With OBSD 4.4 the system hangs only when I activate the second NIC (up, dhcp, IP address). Another test I did was to disable the on-board NIC and put a second off-board NIC, so the system had 3 NICs. The system hangs only when I activate the second NIC. In this case, the DLink NIC (DFE-520TX) make the system show the message Watchdog Timeout. The same NICs in another motherboard doesn't cause the system to hang or to show error messages. Also, Intel says that this board has no support for Linux. Should I discard this model or has something else I can do? Ooops, I forgot to mention that I have 3 of these boards and the same occurs with all of them. Rgds, Marcello - Original Message - From: Stijn mail.st...@telenet.be To: Marcello Cruz marcello.c...@globo.com Sent: Thursday, April 09, 2009 5:03 PM Subject: Re: Intel D945GCNL with OpenBSD 4.4 Hangs OpenBSD 4.4 (GENERIC) #1021: Tue Aug 12 17:16:55 MDT 2008 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC RTC BIOS diagnostic error 80clock_battery mtrr: Pentium Pro MTRR support Hi, Can you disable apm at the boot prompt? This way acpi will be used. Also try a recent snapshot to see if this helps. HTH, Stijn
Re: Intel D945GCNL with OpenBSD 4.4 Hangs
Marcello Cruz wrote: Dear all, I have an Intel D945GCNL board and when I try to enable a second NIC the system hangs. I really don't know where to search for a clue. I took some steps before posting this message: * replaced the HD with another one * replaced the NIC (D-Link DFE-530, 3COM Etherlink, generic NIC with Relatek chipset) * replaced memory Also, I have installed the same periferals on another motherboard (Asus) and had no problem. So I think the problem is with the motherboard. The BIOS doesn't seem to have any configuration regarding PCI slots (where the NIC is installed). Now, I'm trying to update the BIOS in order to see some new implementation not supported by the OpenBSD. Please, I really need a help and I don4t know how to feed you with information. Below is the DMESG. Rgds, Marcello OpenBSD 4.4 (GENERIC) #1021: Tue Aug 12 17:16:55 MDT 2008 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC RTC BIOS diagnostic error 80clock_battery cpu0: Intel(R) Celeron(R) CPU 430 @ 1.80GHz (GenuineIntel 686-class) 1.80 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR real mem = 1062424576 (1013MB) avail mem = 1018863616 (971MB) RTC BIOS diagnostic error 80clock_battery mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 08/28/07, SMBIOS rev. 2.4 @ 0xe44d0 (28 entries) bios0: vendor Intel Corp. version NL94510J.86A.0017.2007.0828.1137 date 08/28/2007 bios0: Intel Corporation D945GCNL apm0 at bios0: Power Management spec V1.2 apm0: AC on, battery charge unknown, estimated 0:00 hours acpi at bios0 function 0x0 not configured pcibios at bios0 function 0x1a not configured bios0: ROM list: 0xc/0xae00! cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 Intel 82945G Host rev 0x02 vga1 at pci0 dev 2 function 0 Intel 82945G Video rev 0x02 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) agp0 at vga1: aperture at 0x4000, size 0x1000 drm at vga1 unsupported azalia0 at pci0 dev 27 function 0 Intel 82801GB HD Audio rev 0x01: irq 9 azalia0: codec[s]: Realtek/0x0888 audio0 at azalia0 ppb0 at pci0 dev 28 function 0 Intel 82801GB PCIE rev 0x01 pci1 at ppb0 bus 1 ppb1 at pci0 dev 28 function 1 Intel 82801GB PCIE rev 0x01 pci2 at ppb1 bus 2 re0 at pci2 dev 0 function 0 Realtek 8168 rev 0x01: RTL8168 2 (0x3800), irq 10, address 00:1c:c0:7b:06:d9 rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2 ppb2 at pci0 dev 28 function 2 Intel 82801GB PCIE rev 0x01 pci3 at ppb2 bus 3 ppb3 at pci0 dev 28 function 3 Intel 82801GB PCIE rev 0x01 pci4 at ppb3 bus 4 uhci0 at pci0 dev 29 function 0 Intel 82801GB USB rev 0x01: irq 11 uhci1 at pci0 dev 29 function 1 Intel 82801GB USB rev 0x01: irq 9 uhci2 at pci0 dev 29 function 2 Intel 82801GB USB rev 0x01: irq 10 uhci3 at pci0 dev 29 function 3 Intel 82801GB USB rev 0x01: irq 11 ehci0 at pci0 dev 29 function 7 Intel 82801GB USB rev 0x01: irq 11 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 Intel EHCI root hub rev 2.00/1.00 addr 1 ppb4 at pci0 dev 30 function 0 Intel 82801BA Hub-to-PCI rev 0xe1 pci5 at ppb4 bus 5 xl0 at pci5 dev 5 function 0 3Com 3c905B 100Base-TX rev 0x24: irq 11, address 00:10:4b:6c:69:53 exphy0 at xl0 phy 24: 3Com internal media interface ichpcib0 at pci0 dev 31 function 0 Intel 82801GB LPC rev 0x01: PM disabled pciide0 at pci0 dev 31 function 1 Intel 82801GB IDE rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility pciide0: channel 0 disabled (no drives) pciide0: channel 1 ignored (disabled) pciide1 at pci0 dev 31 function 2 Intel 82801GB SATA rev 0x01: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI pciide1: using irq 9 for native-PCI interrupt atapiscsi0 at pciide1 channel 0 drive 0 scsibus0 at atapiscsi0: 2 targets, initiator 7 cd0 at scsibus0 targ 0 lun 0: HL-DT-ST, DVDRAM GH20NS15, IL00 ATAPI 5/cdrom removable cd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5 wd0 at pciide1 channel 1 drive 0: SAMSUNG HD161HJ wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors wd0(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 5 ichiic0 at pci0 dev 31 function 3 Intel 82801GB SMBus rev 0x01: irq 9 iic0 at ichiic0 spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5 usb1 at uhci0: USB revision 1.0 uhub1 at usb1 Intel UHCI root hub rev 1.00/1.00 addr 1 usb2 at uhci1: USB revision 1.0 uhub2 at usb2 Intel UHCI root hub rev 1.00/1.00 addr 1 usb3 at uhci2: USB revision 1.0 uhub3 at usb3 Intel UHCI root hub rev 1.00/1.00 addr 1 usb4 at uhci3: USB revision 1.0 uhub4 at usb4 Intel UHCI root hub rev 1.00/1.00 addr 1 isa0 at ichpcib0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at
Intel D945GCNL with OpenBSD 4.4 Hangs
Dear all, I have an Intel D945GCNL board and when I try to enable a second NIC the system hangs. I really don't know where to search for a clue. I took some steps before posting this message: * replaced the HD with another one * replaced the NIC (D-Link DFE-530, 3COM Etherlink, generic NIC with Relatek chipset) * replaced memory Also, I have installed the same periferals on another motherboard (Asus) and had no problem. So I think the problem is with the motherboard. The BIOS doesn't seem to have any configuration regarding PCI slots (where the NIC is installed). Now, I'm trying to update the BIOS in order to see some new implementation not supported by the OpenBSD. Please, I really need a help and I don4t know how to feed you with information. Below is the DMESG. Rgds, Marcello OpenBSD 4.4 (GENERIC) #1021: Tue Aug 12 17:16:55 MDT 2008 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC RTC BIOS diagnostic error 80clock_battery cpu0: Intel(R) Celeron(R) CPU 430 @ 1.80GHz (GenuineIntel 686-class) 1.80 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR real mem = 1062424576 (1013MB) avail mem = 1018863616 (971MB) RTC BIOS diagnostic error 80clock_battery mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 08/28/07, SMBIOS rev. 2.4 @ 0xe44d0 (28 entries) bios0: vendor Intel Corp. version NL94510J.86A.0017.2007.0828.1137 date 08/28/2007 bios0: Intel Corporation D945GCNL apm0 at bios0: Power Management spec V1.2 apm0: AC on, battery charge unknown, estimated 0:00 hours acpi at bios0 function 0x0 not configured pcibios at bios0 function 0x1a not configured bios0: ROM list: 0xc/0xae00! cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 Intel 82945G Host rev 0x02 vga1 at pci0 dev 2 function 0 Intel 82945G Video rev 0x02 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) agp0 at vga1: aperture at 0x4000, size 0x1000 drm at vga1 unsupported azalia0 at pci0 dev 27 function 0 Intel 82801GB HD Audio rev 0x01: irq 9 azalia0: codec[s]: Realtek/0x0888 audio0 at azalia0 ppb0 at pci0 dev 28 function 0 Intel 82801GB PCIE rev 0x01 pci1 at ppb0 bus 1 ppb1 at pci0 dev 28 function 1 Intel 82801GB PCIE rev 0x01 pci2 at ppb1 bus 2 re0 at pci2 dev 0 function 0 Realtek 8168 rev 0x01: RTL8168 2 (0x3800), irq 10, address 00:1c:c0:7b:06:d9 rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2 ppb2 at pci0 dev 28 function 2 Intel 82801GB PCIE rev 0x01 pci3 at ppb2 bus 3 ppb3 at pci0 dev 28 function 3 Intel 82801GB PCIE rev 0x01 pci4 at ppb3 bus 4 uhci0 at pci0 dev 29 function 0 Intel 82801GB USB rev 0x01: irq 11 uhci1 at pci0 dev 29 function 1 Intel 82801GB USB rev 0x01: irq 9 uhci2 at pci0 dev 29 function 2 Intel 82801GB USB rev 0x01: irq 10 uhci3 at pci0 dev 29 function 3 Intel 82801GB USB rev 0x01: irq 11 ehci0 at pci0 dev 29 function 7 Intel 82801GB USB rev 0x01: irq 11 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 Intel EHCI root hub rev 2.00/1.00 addr 1 ppb4 at pci0 dev 30 function 0 Intel 82801BA Hub-to-PCI rev 0xe1 pci5 at ppb4 bus 5 xl0 at pci5 dev 5 function 0 3Com 3c905B 100Base-TX rev 0x24: irq 11, address 00:10:4b:6c:69:53 exphy0 at xl0 phy 24: 3Com internal media interface ichpcib0 at pci0 dev 31 function 0 Intel 82801GB LPC rev 0x01: PM disabled pciide0 at pci0 dev 31 function 1 Intel 82801GB IDE rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility pciide0: channel 0 disabled (no drives) pciide0: channel 1 ignored (disabled) pciide1 at pci0 dev 31 function 2 Intel 82801GB SATA rev 0x01: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI pciide1: using irq 9 for native-PCI interrupt atapiscsi0 at pciide1 channel 0 drive 0 scsibus0 at atapiscsi0: 2 targets, initiator 7 cd0 at scsibus0 targ 0 lun 0: HL-DT-ST, DVDRAM GH20NS15, IL00 ATAPI 5/cdrom removable cd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5 wd0 at pciide1 channel 1 drive 0: SAMSUNG HD161HJ wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors wd0(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 5 ichiic0 at pci0 dev 31 function 3 Intel 82801GB SMBus rev 0x01: irq 9 iic0 at ichiic0 spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5 usb1 at uhci0: USB revision 1.0 uhub1 at usb1 Intel UHCI root hub rev 1.00/1.00 addr 1 usb2 at uhci1: USB revision 1.0 uhub2 at usb2 Intel UHCI root hub rev 1.00/1.00 addr 1 usb3 at uhci2: USB revision 1.0 uhub3 at usb3 Intel UHCI root hub rev 1.00/1.00 addr 1 usb4 at uhci3: USB revision 1.0 uhub4 at usb4 Intel UHCI root hub rev 1.00/1.00 addr 1 isa0 at ichpcib0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at
