Re: [OpenIndiana-discuss] OI on USB flash drive
Hi Reg, Thanks for the efforts. I did try the GUI installer but got the same problem at initial boot. My issue does seem to be the USB controller. It is looking like I'll have to do the slice technique for the rpool on the data drives. They're a pair of 6tb wd reds so I won't loose a lot :-) ... but they're getting a little old and I didn't want to risk the OS on them at well... but it is what it is. I last did it several years ago so I'll have to look it up again! The 8tb I took out of the QNAP and put in an N54L, zfs quickly flagged one of them (which is now RMA) whereas the QNAP was still happy to use it... so I do prefer ZFS for the error checking. Till mentioned SmartOS, so I'll take a look at that, but I by far prefer ZFS wherever I can get it. Many thanks for your efforts and write up. Michelle. On Fri, 2021-04-30 at 22:55 +, Reginald Beardsley via openindiana- discuss wrote: > > > While I don't have prior experience booting from flash drives, I > agree with Till's recommendation to try a USB hard drive. > > Have you tried installing to a regular disk drive and booting from > that? If you can I recommend doing that and skipping the flash drive > boot. The RAIDZ bootloader seems to work though I don't have the 10 > years of experience I have with using 2 slices to provide a mirrored > rpool and a RAIDZ export pool. > > Reg > On Friday, April 30, 2021, 05:22:03 PM CDT, Till Wegmueller < > toaster...@gmail.com> wrote: > > Hi Michelle > > I don't know how happy you are going to get with a QNAP Hardware as > base > for OI. QNAP is very exotic Hardware. It may be USB what they are > using > in princiapl, but unless you are sure the Controllers are actually > the > Controllers they are saying they are and the Storage is not a SD card > in > Hiding, you are going to have a bad time. ZFS does not assume the > Storage to be uncorruptable, and thus far every SD-Card I found was > so > terrible, that one meeting with ZFS showed just how much dataloss > these > cards have. > > QNAP and Synology usually use RAMDISK based approaches which run > fully > in RAM and only use the Storage to boot. > > SmartOS does the same, so this could work. > > In my career and with friends I have seen many OS installation to > USB > drives and SD-cards go horribly wrong. Those storage Options usually > don't survive for long and then the whole OS is gone. I've seen it > with > FreeNAS(FreeBSD), Linux and illumos based Oses. I use Disks or SSD's > as > Storage for the Pools. The Cable can be USB. But it needs to be a > Disk > and not a flashdrive to at least Guarantee some use. > > My Hardware recommendations for Cheap Home Servers for NAS on a > budget > include HP Microservers Gen8 (Gen10 works too, but they spew warnings > on > boot) SuperMicro Mini-ITX Boards. HP Workstations, or Workstations > and > Gaming and Office Rigs in general and of course Dan McDonalds HDC3.0 > [0] > > -Till > > [0] https://kebe.com/blog/?tag=HDC > > On 30.04.21 17:19, Michelle wrote: > > Good suggestions, but sadly didn't work. > > > > Using option 2 single user also fails with the same errors. > > > > I've also tried the USB interface in various booting modes, > > unfortunately none of which work. > > > > I took a look at the variables in the boot options, just for the > > sake > > of it, and couldn't find anything obvious that would help > > > > Michelle. > > > > On Fri, 2021-04-30 at 20:00 +, Reginald Beardsley via > > openindiana- > > discuss wrote: > > > Try selecting the "reconfigure" option when you first boot the > > > installed image. > > > > > > It is *supposed* to reconfigure, but I spent 50 hrs before I > > > found > > > out how to get 2021.04.05 to boot after the install. I thought > > > the > > > issue was the particular nVIDIA driver, but that was not the > > > case. > > > > > > I also got a fresh install of 2021.04.05 to boot properly by > > > coming > > > up single user, "touch /reconfigure; init 6". > > > > > > Good luck, > > > Reg > > > > > > > > > On Friday, April 30, 2021, 02:50:50 PM CDT, Michelle < > > > miche...@msknight.com> wrote: > > > > > > OK, this is where things are going to get a bit awkward. > > > > > > Scenario – QNAP NAS TS-251 decided to install their own Malware > > > Remover > > > which tells me it’s removed files, but doesn’t tell me which ones > > > it’s > > > removed, and I can’t kill the remover itself. If I Ssh in and > > > remove > > > it, it simply re-installs itself. I'm not a fan of malware > > > removers > > > that don't tell you what files they've removed. > > > > > > So… the decision to rip it apart and install my own operating > > > system. > > > After all, it’s on an American Megatrends bios. > > > > > > The 2gig of RAM was replaced with 8, and the storage is a half > > > gig > > > USB > > > flash module. So the flash module has to be replaced also. > > > > > > I thus have a USB header unit and I’ve also tried to install
Re: [OpenIndiana-discuss] OI on USB flash drive
Hi Till, Many thanks for the detailed response. My target is an enterprise Sandisk SSD on the end of a Sata/USB controller. I think I can get it in the case. I've tried a few combinations and have one that boots, so I'm fairly confident that this is now down to tweeking; but I might have reached the end of the road with the USB approach because, as you say, they are a bit exotic. I do have a couple of HP N54L microservers in service for about five years, with the custom BIOS flash so I have hot plug/play. The newer microservers still run to a grand with a decent spec, which is a bit rich for me at the moment; I need to save. This is now just a case of not letting the QNAP go to landfill. You're correct... my model is a half gig flash memory module on a USB header and it unpacks itself into memory. With that gone, I'm at the 2015 American Megatrends BIOS controlling the boot, but I haven't found an update that I trust for that motherboard yet. Thanks for the tip on SmartOS - I'll look it up. Michelle. On Fri, 2021-04-30 at 19:21 -0300, Till Wegmueller wrote: > Hi Michelle > > I don't know how happy you are going to get with a QNAP Hardware as > base > for OI. QNAP is very exotic Hardware. It may be USB what they are > using > in princiapl, but unless you are sure the Controllers are actually > the > Controllers they are saying they are and the Storage is not a SD card > in > Hiding, you are going to have a bad time. ZFS does not assume the > Storage to be uncorruptable, and thus far every SD-Card I found was > so > terrible, that one meeting with ZFS showed just how much dataloss > these > cards have. > > QNAP and Synology usually use RAMDISK based approaches which run > fully > in RAM and only use the Storage to boot. > > SmartOS does the same, so this could work. > > In my career and with friends I have seen many OS installation to > USB > drives and SD-cards go horribly wrong. Those storage Options usually > don't survive for long and then the whole OS is gone. I've seen it > with > FreeNAS(FreeBSD), Linux and illumos based Oses. I use Disks or SSD's > as > Storage for the Pools. The Cable can be USB. But it needs to be a > Disk > and not a flashdrive to at least Guarantee some use. > > My Hardware recommendations for Cheap Home Servers for NAS on a > budget > include HP Microservers Gen8 (Gen10 works too, but they spew warnings > on > boot) SuperMicro Mini-ITX Boards. HP Workstations, or Workstations > and > Gaming and Office Rigs in general and of course Dan McDonalds HDC3.0 > [0] > > -Till > > [0] https://kebe.com/blog/?tag=HDC > > On 30.04.21 17:19, Michelle wrote: > > Good suggestions, but sadly didn't work. > > > > Using option 2 single user also fails with the same errors. > > > > I've also tried the USB interface in various booting modes, > > unfortunately none of which work. > > > > I took a look at the variables in the boot options, just for the > > sake > > of it, and couldn't find anything obvious that would help > > > > Michelle. > > > > On Fri, 2021-04-30 at 20:00 +, Reginald Beardsley via > > openindiana- > > discuss wrote: > > > Try selecting the "reconfigure" option when you first boot the > > > installed image. > > > > > > It is *supposed* to reconfigure, but I spent 50 hrs before I > > > found > > > out how to get 2021.04.05 to boot after the install. I thought > > > the > > > issue was the particular nVIDIA driver, but that was not the > > > case. > > > > > > I also got a fresh install of 2021.04.05 to boot properly by > > > coming > > > up single user, "touch /reconfigure; init 6". > > > > > > Good luck, > > > Reg > > > > > > > > > On Friday, April 30, 2021, 02:50:50 PM CDT, Michelle < > > > miche...@msknight.com> wrote: > > > > > > OK, this is where things are going to get a bit awkward. > > > > > > Scenario – QNAP NAS TS-251 decided to install their own Malware > > > Remover > > > which tells me it’s removed files, but doesn’t tell me which ones > > > it’s > > > removed, and I can’t kill the remover itself. If I Ssh in and > > > remove > > > it, it simply re-installs itself. I'm not a fan of malware > > > removers > > > that don't tell you what files they've removed. > > > > > > So… the decision to rip it apart and install my own operating > > > system. > > > After all, it’s on an American Megatrends bios. > > > > > > The 2gig of RAM was replaced with 8, and the storage is a half > > > gig > > > USB > > > flash module. So the flash module has to be replaced also. > > > > > > I thus have a USB header unit and I’ve also tried to install > > > Hipster > > > to > > > a flash drive connected via a USB harness, and also to a USB key > > > directly. > > > > > > On install, I get an error… > > > > > > openindiana drm: WARNING: [drm:pci_dev_create:93] > > > ddi_prop_get_int() > > > failed > > > > > > … which repeats three or four times during the installation. > > > > > > After installation is finished, the installation OS
Re: [OpenIndiana-discuss] OI on USB flash drive
While I don't have prior experience booting from flash drives, I agree with Till's recommendation to try a USB hard drive. Have you tried installing to a regular disk drive and booting from that? If you can I recommend doing that and skipping the flash drive boot. The RAIDZ bootloader seems to work though I don't have the 10 years of experience I have with using 2 slices to provide a mirrored rpool and a RAIDZ export pool. Reg On Friday, April 30, 2021, 05:22:03 PM CDT, Till Wegmueller wrote: Hi Michelle I don't know how happy you are going to get with a QNAP Hardware as base for OI. QNAP is very exotic Hardware. It may be USB what they are using in princiapl, but unless you are sure the Controllers are actually the Controllers they are saying they are and the Storage is not a SD card in Hiding, you are going to have a bad time. ZFS does not assume the Storage to be uncorruptable, and thus far every SD-Card I found was so terrible, that one meeting with ZFS showed just how much dataloss these cards have. QNAP and Synology usually use RAMDISK based approaches which run fully in RAM and only use the Storage to boot. SmartOS does the same, so this could work. In my career and with friends I have seen many OS installation to USB drives and SD-cards go horribly wrong. Those storage Options usually don't survive for long and then the whole OS is gone. I've seen it with FreeNAS(FreeBSD), Linux and illumos based Oses. I use Disks or SSD's as Storage for the Pools. The Cable can be USB. But it needs to be a Disk and not a flashdrive to at least Guarantee some use. My Hardware recommendations for Cheap Home Servers for NAS on a budget include HP Microservers Gen8 (Gen10 works too, but they spew warnings on boot) SuperMicro Mini-ITX Boards. HP Workstations, or Workstations and Gaming and Office Rigs in general and of course Dan McDonalds HDC3.0 [0] -Till [0] https://kebe.com/blog/?tag=HDC On 30.04.21 17:19, Michelle wrote: > Good suggestions, but sadly didn't work. > > Using option 2 single user also fails with the same errors. > > I've also tried the USB interface in various booting modes, > unfortunately none of which work. > > I took a look at the variables in the boot options, just for the sake > of it, and couldn't find anything obvious that would help > > Michelle. > > On Fri, 2021-04-30 at 20:00 +, Reginald Beardsley via openindiana- > discuss wrote: >> Try selecting the "reconfigure" option when you first boot the >> installed image. >> >> It is *supposed* to reconfigure, but I spent 50 hrs before I found >> out how to get 2021.04.05 to boot after the install. I thought the >> issue was the particular nVIDIA driver, but that was not the case. >> >> I also got a fresh install of 2021.04.05 to boot properly by coming >> up single user, "touch /reconfigure; init 6". >> >> Good luck, >> Reg >> >> >> On Friday, April 30, 2021, 02:50:50 PM CDT, Michelle < >> miche...@msknight.com> wrote: >> >> OK, this is where things are going to get a bit awkward. >> >> Scenario – QNAP NAS TS-251 decided to install their own Malware >> Remover >> which tells me it’s removed files, but doesn’t tell me which ones >> it’s >> removed, and I can’t kill the remover itself. If I Ssh in and remove >> it, it simply re-installs itself. I'm not a fan of malware removers >> that don't tell you what files they've removed. >> >> So… the decision to rip it apart and install my own operating system. >> After all, it’s on an American Megatrends bios. >> >> The 2gig of RAM was replaced with 8, and the storage is a half gig >> USB >> flash module. So the flash module has to be replaced also. >> >> I thus have a USB header unit and I’ve also tried to install Hipster >> to >> a flash drive connected via a USB harness, and also to a USB key >> directly. >> >> On install, I get an error… >> >> openindiana drm: WARNING: [drm:pci_dev_create:93] ddi_prop_get_int() >> failed >> >> … which repeats three or four times during the installation. >> >> After installation is finished, the installation OS goes down, but >> says… >> >> openindiana genunix:WARNING: xhci has no quiesce() >> reboot: not all drivers have implemented quiesce(9E) >> Please see veradm/messages for drivers that haven’t implemented >> quiesce(9E) >> Failed to process boot arguments from Boot Environment. >> Falling back to regular reboot >> >> Then on reboot, the boot comes up but gives… >> >> WARNING: pci@0,0pci8086,f35@14/storage@3/disk@0,0 (sd0): >> Commend failed to complete… Device is gone >> Warning: Pool “rpool” has encountered an uncorrectable I/O failure >> and >> has been suspended; “zpool clear” will be required before the poor >> can >> be written to. >> Warning: pci@0,0/pci8086/f35@14/storage@3 (scsa2usb0): Reinserted >> device is accessible again. >> Warning: Pool “rpool” has encountered an incorrectable I/O failure >> and >> has been suspended; “zpool clear” will be required before the poor >> can >> be written
Re: [OpenIndiana-discuss] OI on USB flash drive
The install completed normally. On the first boot attempt I selected every boot option *except* graphical console. It stalled part way with SCSI time outs. I inadvertently dropped the power while messing with other stuff. In the 2nd boot attempt I selected *all* the boot options in 2021.04.05. This time it came up to single user mode. I logged in as root and took a quick look at the pool and when I hit ^d it came up and started lightdm. It did *not* install the nVIDIA driver, but is otherwise fully functional. Running "nvidia-xconfig" hosed lightdm and I've not been able to restart that. Deleting /etc/xorg.conf and doing an "init 6" fixed it and I came up with lightdm running and 1600x1200 resolution in landscape mode. I don't know if this helps or not. There is clearly something strange going on. I just tried a reboot using the same options as the first time after the install. It came up all the way when I hit ^d at the single user prompt. Reg On Friday, April 30, 2021, 04:21:19 PM CDT, Reginald Beardsley via openindiana-discuss wrote: I've started an install of 2021.04.05 to a 32 GB flash drive on a Z400. I'll see if that provides any information. I used the text installer from the GUI desktop, so it will be slow. My 8 port KVM switch died so most of my systems were down. The replacement, a 4 port dual monitor KVM switch came today. Then I discovered that I also need Display Port to VGA adapters :-( When I set up my NL40 it was not possible to boot from a RAIDZ, so the popular wisdom was to use a USB flash drive for the root pool. I didn't like that so I created a 100 GB rpool slice in s0 and the rest of the disk in s1. After installing into the rpool, I created a 4 way mirror and a 4 disk RAIDZ2 array. I recently rebuilt it using a single RAIDZ2 array to verify we could now boot from RAIDZ. It worked fine. I'll post once the install finishes and I've had time to mess with it a bit. I assume you've checked that the BIOS will allow USB boot. IIRC the Z400 would not boot from the USB Live Image. So I don't hold out a lot of hope, but it's not much effort for me to give it a try. Reg ___ openindiana-discuss mailing list openindiana-discuss@openindiana.org https://openindiana.org/mailman/listinfo/openindiana-discuss
Re: [OpenIndiana-discuss] OI on USB flash drive
Hi Michelle I don't know how happy you are going to get with a QNAP Hardware as base for OI. QNAP is very exotic Hardware. It may be USB what they are using in princiapl, but unless you are sure the Controllers are actually the Controllers they are saying they are and the Storage is not a SD card in Hiding, you are going to have a bad time. ZFS does not assume the Storage to be uncorruptable, and thus far every SD-Card I found was so terrible, that one meeting with ZFS showed just how much dataloss these cards have. QNAP and Synology usually use RAMDISK based approaches which run fully in RAM and only use the Storage to boot. SmartOS does the same, so this could work. In my career and with friends I have seen many OS installation to USB drives and SD-cards go horribly wrong. Those storage Options usually don't survive for long and then the whole OS is gone. I've seen it with FreeNAS(FreeBSD), Linux and illumos based Oses. I use Disks or SSD's as Storage for the Pools. The Cable can be USB. But it needs to be a Disk and not a flashdrive to at least Guarantee some use. My Hardware recommendations for Cheap Home Servers for NAS on a budget include HP Microservers Gen8 (Gen10 works too, but they spew warnings on boot) SuperMicro Mini-ITX Boards. HP Workstations, or Workstations and Gaming and Office Rigs in general and of course Dan McDonalds HDC3.0 [0] -Till [0] https://kebe.com/blog/?tag=HDC On 30.04.21 17:19, Michelle wrote: Good suggestions, but sadly didn't work. Using option 2 single user also fails with the same errors. I've also tried the USB interface in various booting modes, unfortunately none of which work. I took a look at the variables in the boot options, just for the sake of it, and couldn't find anything obvious that would help Michelle. On Fri, 2021-04-30 at 20:00 +, Reginald Beardsley via openindiana- discuss wrote: Try selecting the "reconfigure" option when you first boot the installed image. It is *supposed* to reconfigure, but I spent 50 hrs before I found out how to get 2021.04.05 to boot after the install. I thought the issue was the particular nVIDIA driver, but that was not the case. I also got a fresh install of 2021.04.05 to boot properly by coming up single user, "touch /reconfigure; init 6". Good luck, Reg On Friday, April 30, 2021, 02:50:50 PM CDT, Michelle < miche...@msknight.com> wrote: OK, this is where things are going to get a bit awkward. Scenario – QNAP NAS TS-251 decided to install their own Malware Remover which tells me it’s removed files, but doesn’t tell me which ones it’s removed, and I can’t kill the remover itself. If I Ssh in and remove it, it simply re-installs itself. I'm not a fan of malware removers that don't tell you what files they've removed. So… the decision to rip it apart and install my own operating system. After all, it’s on an American Megatrends bios. The 2gig of RAM was replaced with 8, and the storage is a half gig USB flash module. So the flash module has to be replaced also. I thus have a USB header unit and I’ve also tried to install Hipster to a flash drive connected via a USB harness, and also to a USB key directly. On install, I get an error… openindiana drm: WARNING: [drm:pci_dev_create:93] ddi_prop_get_int() failed … which repeats three or four times during the installation. After installation is finished, the installation OS goes down, but says… openindiana genunix:WARNING: xhci has no quiesce() reboot: not all drivers have implemented quiesce(9E) Please see veradm/messages for drivers that haven’t implemented quiesce(9E) Failed to process boot arguments from Boot Environment. Falling back to regular reboot Then on reboot, the boot comes up but gives… WARNING: pci@0,0pci8086,f35@14/storage@3/disk@0,0 (sd0): Commend failed to complete… Device is gone Warning: Pool “rpool” has encountered an uncorrectable I/O failure and has been suspended; “zpool clear” will be required before the poor can be written to. Warning: pci@0,0/pci8086/f35@14/storage@3 (scsa2usb0): Reinserted device is accessible again. Warning: Pool “rpool” has encountered an incorrectable I/O failure and has been suspended; “zpool clear” will be required before the poor can be written to. ...that last repeats three times and the unit sits there. I did try searching for devices with no drivers, but the only thing that came up were the two processor cores. I did try creating a Solaris 2 partition and installing to a partition instead of the EFI whole disk option, but that failed on fdisk and didn’t even install the files. I had to destroy the partition table in order to get back to getting the installation to work. Also, in the installer, when I tried to go to a partition installation and pressed F5 to change the partition type, it would go back to the installation menu again, so I’m presuming that it just doesn’t like the USB as a target. I’ve got an ugly feeling that I’ve got no way of getting around
Re: [OpenIndiana-discuss] OI on USB flash drive
I've started an install of 2021.04.05 to a 32 GB flash drive on a Z400. I'll see if that provides any information. I used the text installer from the GUI desktop, so it will be slow. My 8 port KVM switch died so most of my systems were down. The replacement, a 4 port dual monitor KVM switch came today. Then I discovered that I also need Display Port to VGA adapters :-( When I set up my NL40 it was not possible to boot from a RAIDZ, so the popular wisdom was to use a USB flash drive for the root pool. I didn't like that so I created a 100 GB rpool slice in s0 and the rest of the disk in s1. After installing into the rpool, I created a 4 way mirror and a 4 disk RAIDZ2 array. I recently rebuilt it using a single RAIDZ2 array to verify we could now boot from RAIDZ. It worked fine. I'll post once the install finishes and I've had time to mess with it a bit. I assume you've checked that the BIOS will allow USB boot. IIRC the Z400 would not boot from the USB Live Image. So I don't hold out a lot of hope, but it's not much effort for me to give it a try. Reg On Friday, April 30, 2021, 03:20:15 PM CDT, Michelle wrote: Good suggestions, but sadly didn't work. Using option 2 single user also fails with the same errors. I've also tried the USB interface in various booting modes, unfortunately none of which work. I took a look at the variables in the boot options, just for the sake of it, and couldn't find anything obvious that would help Michelle. On Fri, 2021-04-30 at 20:00 +, Reginald Beardsley via openindiana- discuss wrote: > Try selecting the "reconfigure" option when you first boot the > installed image. > > It is *supposed* to reconfigure, but I spent 50 hrs before I found > out how to get 2021.04.05 to boot after the install. I thought the > issue was the particular nVIDIA driver, but that was not the case. > > I also got a fresh install of 2021.04.05 to boot properly by coming > up single user, "touch /reconfigure; init 6". > > Good luck, > Reg > > > On Friday, April 30, 2021, 02:50:50 PM CDT, Michelle < > miche...@msknight.com> wrote: > > OK, this is where things are going to get a bit awkward. > > Scenario – QNAP NAS TS-251 decided to install their own Malware > Remover > which tells me it’s removed files, but doesn’t tell me which ones > it’s > removed, and I can’t kill the remover itself. If I Ssh in and remove > it, it simply re-installs itself. I'm not a fan of malware removers > that don't tell you what files they've removed. > > So… the decision to rip it apart and install my own operating system. > After all, it’s on an American Megatrends bios. > > The 2gig of RAM was replaced with 8, and the storage is a half gig > USB > flash module. So the flash module has to be replaced also. > > I thus have a USB header unit and I’ve also tried to install Hipster > to > a flash drive connected via a USB harness, and also to a USB key > directly. > > On install, I get an error… > > openindiana drm: WARNING: [drm:pci_dev_create:93] ddi_prop_get_int() > failed > > … which repeats three or four times during the installation. > > After installation is finished, the installation OS goes down, but > says… > > openindiana genunix:WARNING: xhci has no quiesce() > reboot: not all drivers have implemented quiesce(9E) > Please see veradm/messages for drivers that haven’t implemented > quiesce(9E) > Failed to process boot arguments from Boot Environment. > Falling back to regular reboot > > Then on reboot, the boot comes up but gives… > > WARNING: pci@0,0pci8086,f35@14/storage@3/disk@0,0 (sd0): > Commend failed to complete… Device is gone > Warning: Pool “rpool” has encountered an uncorrectable I/O failure > and > has been suspended; “zpool clear” will be required before the poor > can > be written to. > Warning: pci@0,0/pci8086/f35@14/storage@3 (scsa2usb0): Reinserted > device is accessible again. > Warning: Pool “rpool” has encountered an incorrectable I/O failure > and > has been suspended; “zpool clear” will be required before the poor > can > be written to. > > ...that last repeats three times and the unit sits there. > > I did try searching for devices with no drivers, but the only thing > that came up were the two processor cores. > > I did try creating a Solaris 2 partition and installing to a > partition > instead of the EFI whole disk option, but that failed on fdisk and > didn’t even install the files. I had to destroy the partition table > in > order to get back to getting the installation to work. > > Also, in the installer, when I tried to go to a partition > installation > and pressed F5 to change the partition type, it would go back to the > installation menu again, so I’m presuming that it just doesn’t like > the > USB as a target. > > I’ve got an ugly feeling that I’ve got no way of getting around > this. > Yes, I know I can put the SATA drives in and make a slice for rpool, > but where’s the fun in that? > > >
Re: [OpenIndiana-discuss] OI on USB flash drive
Good suggestions, but sadly didn't work. Using option 2 single user also fails with the same errors. I've also tried the USB interface in various booting modes, unfortunately none of which work. I took a look at the variables in the boot options, just for the sake of it, and couldn't find anything obvious that would help Michelle. On Fri, 2021-04-30 at 20:00 +, Reginald Beardsley via openindiana- discuss wrote: > Try selecting the "reconfigure" option when you first boot the > installed image. > > It is *supposed* to reconfigure, but I spent 50 hrs before I found > out how to get 2021.04.05 to boot after the install. I thought the > issue was the particular nVIDIA driver, but that was not the case. > > I also got a fresh install of 2021.04.05 to boot properly by coming > up single user, "touch /reconfigure; init 6". > > Good luck, > Reg > > > On Friday, April 30, 2021, 02:50:50 PM CDT, Michelle < > miche...@msknight.com> wrote: > > OK, this is where things are going to get a bit awkward. > > Scenario – QNAP NAS TS-251 decided to install their own Malware > Remover > which tells me it’s removed files, but doesn’t tell me which ones > it’s > removed, and I can’t kill the remover itself. If I Ssh in and remove > it, it simply re-installs itself. I'm not a fan of malware removers > that don't tell you what files they've removed. > > So… the decision to rip it apart and install my own operating system. > After all, it’s on an American Megatrends bios. > > The 2gig of RAM was replaced with 8, and the storage is a half gig > USB > flash module. So the flash module has to be replaced also. > > I thus have a USB header unit and I’ve also tried to install Hipster > to > a flash drive connected via a USB harness, and also to a USB key > directly. > > On install, I get an error… > > openindiana drm: WARNING: [drm:pci_dev_create:93] ddi_prop_get_int() > failed > > … which repeats three or four times during the installation. > > After installation is finished, the installation OS goes down, but > says… > > openindiana genunix:WARNING: xhci has no quiesce() > reboot: not all drivers have implemented quiesce(9E) > Please see veradm/messages for drivers that haven’t implemented > quiesce(9E) > Failed to process boot arguments from Boot Environment. > Falling back to regular reboot > > Then on reboot, the boot comes up but gives… > > WARNING: pci@0,0pci8086,f35@14/storage@3/disk@0,0 (sd0): > Commend failed to complete… Device is gone > Warning: Pool “rpool” has encountered an uncorrectable I/O failure > and > has been suspended; “zpool clear” will be required before the poor > can > be written to. > Warning: pci@0,0/pci8086/f35@14/storage@3 (scsa2usb0): Reinserted > device is accessible again. > Warning: Pool “rpool” has encountered an incorrectable I/O failure > and > has been suspended; “zpool clear” will be required before the poor > can > be written to. > > ...that last repeats three times and the unit sits there. > > I did try searching for devices with no drivers, but the only thing > that came up were the two processor cores. > > I did try creating a Solaris 2 partition and installing to a > partition > instead of the EFI whole disk option, but that failed on fdisk and > didn’t even install the files. I had to destroy the partition table > in > order to get back to getting the installation to work. > > Also, in the installer, when I tried to go to a partition > installation > and pressed F5 to change the partition type, it would go back to the > installation menu again, so I’m presuming that it just doesn’t like > the > USB as a target. > > I’ve got an ugly feeling that I’ve got no way of getting around > this. > Yes, I know I can put the SATA drives in and make a slice for rpool, > but where’s the fun in that? > > > ___ > openindiana-discuss mailing list > openindiana-discuss@openindiana.org > https://openindiana.org/mailman/listinfo/openindiana-discuss > > ___ > openindiana-discuss mailing list > openindiana-discuss@openindiana.org > https://openindiana.org/mailman/listinfo/openindiana-discuss ___ openindiana-discuss mailing list openindiana-discuss@openindiana.org https://openindiana.org/mailman/listinfo/openindiana-discuss
Re: [OpenIndiana-discuss] OI on USB flash drive
Try selecting the "reconfigure" option when you first boot the installed image. It is *supposed* to reconfigure, but I spent 50 hrs before I found out how to get 2021.04.05 to boot after the install. I thought the issue was the particular nVIDIA driver, but that was not the case. I also got a fresh install of 2021.04.05 to boot properly by coming up single user, "touch /reconfigure; init 6". Good luck, Reg On Friday, April 30, 2021, 02:50:50 PM CDT, Michelle wrote: OK, this is where things are going to get a bit awkward. Scenario – QNAP NAS TS-251 decided to install their own Malware Remover which tells me it’s removed files, but doesn’t tell me which ones it’s removed, and I can’t kill the remover itself. If I Ssh in and remove it, it simply re-installs itself. I'm not a fan of malware removers that don't tell you what files they've removed. So… the decision to rip it apart and install my own operating system. After all, it’s on an American Megatrends bios. The 2gig of RAM was replaced with 8, and the storage is a half gig USB flash module. So the flash module has to be replaced also. I thus have a USB header unit and I’ve also tried to install Hipster to a flash drive connected via a USB harness, and also to a USB key directly. On install, I get an error… openindiana drm: WARNING: [drm:pci_dev_create:93] ddi_prop_get_int() failed … which repeats three or four times during the installation. After installation is finished, the installation OS goes down, but says… openindiana genunix:WARNING: xhci has no quiesce() reboot: not all drivers have implemented quiesce(9E) Please see veradm/messages for drivers that haven’t implemented quiesce(9E) Failed to process boot arguments from Boot Environment. Falling back to regular reboot Then on reboot, the boot comes up but gives… WARNING: pci@0,0pci8086,f35@14/storage@3/disk@0,0 (sd0): Commend failed to complete… Device is gone Warning: Pool “rpool” has encountered an uncorrectable I/O failure and has been suspended; “zpool clear” will be required before the poor can be written to. Warning: pci@0,0/pci8086/f35@14/storage@3 (scsa2usb0): Reinserted device is accessible again. Warning: Pool “rpool” has encountered an incorrectable I/O failure and has been suspended; “zpool clear” will be required before the poor can be written to. ...that last repeats three times and the unit sits there. I did try searching for devices with no drivers, but the only thing that came up were the two processor cores. I did try creating a Solaris 2 partition and installing to a partition instead of the EFI whole disk option, but that failed on fdisk and didn’t even install the files. I had to destroy the partition table in order to get back to getting the installation to work. Also, in the installer, when I tried to go to a partition installation and pressed F5 to change the partition type, it would go back to the installation menu again, so I’m presuming that it just doesn’t like the USB as a target. I’ve got an ugly feeling that I’ve got no way of getting around this. Yes, I know I can put the SATA drives in and make a slice for rpool, but where’s the fun in that? ___ openindiana-discuss mailing list openindiana-discuss@openindiana.org https://openindiana.org/mailman/listinfo/openindiana-discuss ___ openindiana-discuss mailing list openindiana-discuss@openindiana.org https://openindiana.org/mailman/listinfo/openindiana-discuss